In article <[EMAIL PROTECTED]>,
Andras HORVATH <[EMAIL PROTECTED]> writes:
> diszket. Ugy latszik, kifutott a hardver a reallokalhato szektorokbol,
> akkor pedig a kovetkezo legkisebb problema is adatvesztessel fog jarni.
Ha a Reallocated_Sector_Ct mutatja, akkor nem.
Egyebkent eleg kriptikus, amit latok.
Az "Error: UNC 8 sectors at LBA = 0x01359675 = 20289141" nagyjabol
egybevag azzal, amit kiserletezessel deritettem ki, csak en a
20289144..20289151 tartomanyt hoztam ki hibasnak.
Hozzaerto szem mit vel felfedezni az alabbiakban?
kissg
----------------------------------------------------------------------------
# smartctl -d ata -F samsung -a /dev/sda
smartctl version 5.36 [x86_64-unknown-linux-gnu] Copyright (C) 2002-6 Bruce
Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HD160JJ
Serial Number: S08HJ1OL808654
Firmware Version: ZM100-41
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a
Local Time is: Tue Jun 12 09:44:59 2007 CEST
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (3701) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 61) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 253 100 051 Pre-fail Always
- 0
3 Spin_Up_Time 0x0007 100 100 025 Pre-fail Always
- 5632
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always
- 886
5 Reallocated_Sector_Ct 0x0033 253 253 010 Pre-fail Always
- 0
7 Seek_Error_Rate 0x000f 253 253 051 Pre-fail Always
- 0
8 Seek_Time_Performance 0x0025 253 253 015 Pre-fail Offline
- 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always
- 1301
10 Spin_Retry_Count 0x0033 253 253 051 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x0012 253 253 000 Old_age Always
- 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always
- 469
187 Unknown_Attribute 0x0032 001 001 000 Old_age Always
- 131282
190 Unknown_Attribute 0x0022 124 058 000 Old_age Always
- 38
194 Temperature_Celsius 0x0022 124 058 000 Old_age Always
- 38
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always
- 57898
196 Reallocated_Event_Count 0x0032 253 253 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always
- 1
198 Offline_Uncorrectable 0x0030 253 253 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x000a 253 100 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 100 000 Old_age Always
- 0
202 TA_Increase_Count 0x0032 253 253 000 Old_age Always
- 0
SMART Error Log Version: 1
ATA Error Count: 53760 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 53760 occurred at disk power-on lifetime: 3589 hours (149 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 75 96 35 e1 Error: UNC 8 sectors at LBA = 0x01359675 = 20289141
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 75 96 35 e1 00 14d+15:00:23.425 READ DMA
ec 00 46 00 00 00 a0 00 35d+00:12:52.353 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 35d+00:12:52.353 SET FEATURES [Set transfer mode]
ec 00 06 78 96 35 a0 00 35d+00:12:52.353 IDENTIFY DEVICE
Error 53759 occurred at disk power-on lifetime: 3589 hours (149 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 75 96 35 e1 Error: UNC 8 sectors at LBA = 0x01359675 = 20289141
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 75 96 35 e1 00 10d+17:40:20.353 READ DMA
ec 00 46 00 00 00 a0 00 30d+22:13:12.065 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 30d+22:13:12.065 SET FEATURES [Set transfer mode]
ec 00 06 78 96 35 a0 00 30d+22:13:12.065 IDENTIFY DEVICE
Error 53758 occurred at disk power-on lifetime: 3589 hours (149 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 75 96 35 e1 Error: UNC 8 sectors at LBA = 0x01359675 = 20289141
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 75 96 35 e1 00 6d+15:40:40.065 READ DMA
ec 00 46 00 00 00 a0 00 27d+00:53:08.993 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 27d+00:53:08.993 SET FEATURES [Set transfer mode]
ec 00 06 78 96 35 a0 00 27d+00:53:08.993 IDENTIFY DEVICE
Error 53757 occurred at disk power-on lifetime: 3589 hours (149 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 75 96 35 e1 Error: UNC 8 sectors at LBA = 0x01359675 = 20289141
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 75 96 35 e1 00 2d+18:20:36.993 READ DMA
ec 00 46 00 00 00 a0 00 22d+22:53:28.705 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 22d+22:53:28.705 SET FEATURES [Set transfer mode]
ec 00 06 78 96 35 a0 00 22d+22:53:28.705 IDENTIFY DEVICE
Error 53756 occurred at disk power-on lifetime: 3589 hours (149 days + 13 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 75 96 35 e1 Error: UNC 8 sectors at LBA = 0x01359675 = 20289141
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 75 96 35 e1 00 10d+21:57:01.313 READ DMA
ec 00 46 00 00 00 a0 00 19d+01:33:25.633 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 19d+01:33:25.633 SET FEATURES [Set transfer mode]
ec 00 06 78 96 35 a0 00 44d+12:02:35.393 IDENTIFY DEVICE
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure
revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
----------------------------------------------------------------------------
_________________________________________________
linux lista - linux@mlf.linux.rulez.org
http://mlf2.linux.rulez.org/mailman/listinfo/linux
