On Nov 14, 2007 4:33 PM, Clemens Koller <[EMAIL PROTECTED]> wrote: > Hi, Robert! > > Just one more short note... > My good - vs. - bad dmesg output: > > good 2.6.21-rc5-git: > > Gianfar MII Bus: probed > > eth0: Gianfar Ethernet Controller Version 1.2, 00:ww:xx:yy:zz:dd > > eth0: Running with NAPI enabled > > eth0: 256/256 RX/TX BD ring size > > eth1: Gianfar Ethernet Controller Version 1.2, 00:ww:xx:yy:zz:dd > > eth1: Running with NAPI enabled > > eth1: 256/256 RX/TX BD ring size > > eth2: Gianfar Ethernet Controller Version 1.2, 00:ww:xx:yy:zz:dd > > eth2: Running with NAPI enabled > > eth2: 256/256 RX/TX BD ring size > > Marvell 88E1101: Registered new driver > > Marvell 88E1111: Registered new driver > > Marvell 88E1145: Registered new driver > (I've wiped out my MAC) > > bad 2.6.24-rc2-git: > < Gianfar MII Bus: probed > < eth0: Gianfar Ethernet Controller Version 1.2, 00:00:00:00:00:00 > < eth0: Running with NAPI enabled > < eth0: 256/256 RX/TX BD ring size > < eth1: Gianfar Ethernet Controller Version 1.2, 00:00:00:00:00:00 > < eth1: Running with NAPI enabled > < eth1: 256/256 RX/TX BD ring size > < eth2: Gianfar Ethernet Controller Version 1.2, 00:00:00:00:00:00 > < eth2: Running with NAPI enabled > < eth2: 256/256 RX/TX BD ring size > > The MACs are all 00 here. > The PHY drivers don't get registered. > (What happened to CONFIG_NETDEV_1000 in the newer kernels?) > > How is your mileage? > Next round... tomorrow, > > regards, > > Clemens Koller
Hmm, I'm getting my mac addresses, the same ones I set in u-boot: => bootm 1000000 - c00000 ## Booting image at 01000000 ... Image Name: Linux-2.6.24-rc2-ge6a5c27f-dirty Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 1278631 Bytes = 1.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK ## Current stack ends at 0x3FF9DD50 => set upper limit to 0x00800000 ## cmdline at 0x007FFF00 ... 0x007FFF90 bd address = 0x3FF9DFB0 memstart = 0x00000000 memsize = 0x40000000 flashstart = 0xF8000000 flashsize = 0x08000000 flashoffset = 0x00000000 sramstart = 0x00000000 sramsize = 0x00000000 immr_base = 0xE0000000 bootflags = 0xE4013F80 intfreq = 888.888 MHz busfreq = 355.555 MHz ethaddr = 00:E0:0C:00:00:FD eth1addr = 00:E0:0C:00:01:FD eth2addr = 00:E0:0C:00:02:FD eth3addr = 00:E0:0C:00:03:FD IP addr = 10.101.43.142 baudrate = 115200 bps Skipping initrd Booting using the fdt at 0xc00000 No initrd ## device tree at 0x00C00000 ... 0x00C01B6C (len=7021=0x1B6D) Loading Device Tree to 007fc000, end 007fdb6c ... OK ## Transferring control to Linux (at address 00000000) ... serial8250.0: ttyS1 at MMIO 0xe0004600 (irq = 42) is a 16550A RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize loop: module loaded Gianfar MII Bus: probed eth0: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:00:00:fd eth0: Running with NAPI enabled eth0: 256/256 RX/TX BD ring size eth1: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:00:01:fd eth1: Running with NAPI enabled eth1: 256/256 RX/TX BD ring size eth2: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:00:02:fd eth2: Running with NAPI enabled eth2: 256/256 RX/TX BD ring size eth3: Gianfar Ethernet Controller Version 1.2, 00:e0:0c:00:03:fd eth3: Running with NAPI enabled eth3: 256/256 RX/TX BD ring size Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx TCP cubic registered Initializing XFRM netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. e0024520:02 not found eth2: Could not attach to PHY IP-Config: Failed to open eth2 IP-Config: Device `eth2' not found. Tomorrow's a holiday here in Brazil, will catch up with you Friday, Robert _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded