the 40 cc was measured with the piston at tdc, the piston doesnt quiet make it level with top of block. i thought that piston was a bit small.....:-)))).
mark k ----- Original Message ----- From: "David Costello" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Friday, June 28, 2002 3:13 AM Subject: Re: Tuning Cars (off topic) > hehe well that explains it then, those piston dishes must be pretty deep, > 40cc is huge > > when I said 32mm Z20 pistons I was refering to the compression height. The > Z20's have 2 different pistons one set are 32mm high, the others are 38.55 > I was assuming you used the 32mm ones cause the 38.55mm ones would be above > deck height > > Dave > > > ----- Original Message ----- > From: "mark krawczuk" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Thursday, June 27, 2002 11:09 PM > Subject: Re: Tuning Cars (off topic) > > > > my bore is 86 mm, the gasket hole is a little bigger , so i reckon that > it > > would be a hole of about 87mm. > > my head cc is 45 > > bore 86 > > stroke 96 > > 2mm head gasket approx 11.76 cc > > > > the volume with dished pistons that havent been machined , and the > > piston at tdc is 40 cc. (fluid level with top of block) > > > > what do you mean 32mm z20e pistons, mine pistons are 86 mm ( 1 mm > > oversize) > > > > > > i have been plugging these figures in a comp ratio calc and seem to be > > getting about 6.7:1 comp can any body double check these figures? > > i know before i said it was about 7.8 :1 but this is what i was pretty > > sure it was... which was of the top of my head. > > the figures above are actually what i have written down. > > > > > > mark k > > > > ----- Original Message ----- > > From: "David Costello" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Thursday, June 27, 2002 6:56 PM > > Subject: Re: Tuning Cars (off topic) > > > > > > > shit, how'd you get the compression that low? > > > the dish on the pistons must be huge > > > using Z24 crank, L20B rods, 2mm copper gasket and the 32mm Z20E pistons > it > > > gives a comp ratio of 11:1 > > > and you said you were running 87mm bore...that's around 11.4:1 > > > > > > Dave > > > > > > ----- Original Message ----- > > > From: "mark krawczuk" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Thursday, June 27, 2002 8:08 AM > > > Subject: Re: Tuning Cars (off topic) > > > > > > > > > > hi, i have dished z20 ( you can get flat or dished), which i got > > machined > > > > out a bit more, then when i had to redo he engine i just put the dish > > > type > > > > back in withoutt geting them machined out more. i can work it out > more > > > > exact if ya want me to but i think i ended up with about 7.8:1 or > > 7.9:1 > > > > > > > > and yes, z20 pistons on l20b rods. > > > > > > > > mark k > > > > ----- Original Message ----- > > > > From: "David Costello" <[EMAIL PROTECTED]> > > > > To: <[EMAIL PROTECTED]> > > > > Sent: Thursday, June 27, 2002 12:41 AM > > > > Subject: Re: Tuning Cars (off topic) > > > > > > > > > > > > > hey mark, slightly off this threads topic here, but what compression > > > ratio > > > > > did your L/Z combo end up with? > > > > > you used Z20E pistons and L20B rods didn't you? > > > > > > > > > > Dave > > > > > ----- Original Message ----- > > > > > From: "mark krawczuk" <[EMAIL PROTECTED]> > > > > > To: <[EMAIL PROTECTED]> > > > > > Sent: Thursday, June 27, 2002 1:07 AM > > > > > Subject: Re: Tuning Cars (off topic) > > > > > > > > > > > > > > > > i have pics of the body, and engine but non of the internals of > the > > > > > > engine. i did have some internal engine film on a handycam tape > > but > > > > it > > > > > > got chewed up, when i get the energy i might see if i can salvage > > > > > something > > > > > > of it. > > > > > > if you want i can burn u a cd with some pics of my datsun. email > me > > > : > > > > > > [EMAIL PROTECTED] > > > > > > witth a postal addresif you want them .. for free !!!! > > > > > > > > > > > > mark k > > > > > > ----- Original Message ----- > > > > > > From: "Paul Stanley" <[EMAIL PROTECTED]> > > > > > > To: <[EMAIL PROTECTED]> > > > > > > Sent: Wednesday, June 26, 2002 11:01 PM > > > > > > Subject: Re: Tuning Cars (off topic) > > > > > > > > > > > > > > > > > > > Do you have pictures? > > > > > > > > > > > > > > From: Paul Stanley > > > > > > > [EMAIL PROTECTED] > > > > > > > > > > > > > > > > > > > > > > > > > > > > ----- Original Message ----- > > > > > > > From: mark krawczuk <[EMAIL PROTECTED]> > > > > > > > To: <[EMAIL PROTECTED]> > > > > > > > Sent: Wednesday, June 26, 2002 4:47 PM > > > > > > > Subject: Re: Tuning Cars (off topic) > > > > > > > > > > > > > > > > > > > > > > l20 b block (4cyl), with navara 2.4 crank,z18 efi head, T3 > > > > turbo@10 > > > > > > psi, > > > > > > > > ivan ttighe cam,boost retard dizzy,v8 commodore throttle body > > and > > > > > > toyota > > > > > > > > 7mgte injectors.......... > > > > > > > > > > > > > > > > mark k > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
