Pull the radiator and remove the hood. You will be cussing yourself otherwise...

Since you have a short nose crank, it is critical that you handle the
crankbolt correctly. I would recommend a bracket to hold the engine
position so you can remove and properly retorque the crank bolt. I use
the one from http://www.rennenmetal.com/products.asp?cat=11.

Also, make sure you replace the key and crank bolt with a new one. Do
not reuse the old one. Check the condition and do the keyway repair if
necessary.

The front main seal is not hard to replace, but a proper seal puller
makes the job much easier. I have struggled with prying them out with
a screwdriver before. Buy a $5 tool and make it a 5 second job. Also
replace the CAM seals while you are in there.

Good luck.

KEN




On Wed, May 14, 2008 at 9:31 PM, Brad Franks <[EMAIL PROTECTED]> wrote:
> So,
>
> After talking with Bill C (what a phenomenal asset to this list and the
> community!) I decided to go with swapping the head gasket. While I'm in
> there I'll be doing the other large maintenance items. The list includes:
>
> Head Gasket & associated top end gaskets (minus intake/exhaust, to be
> reused)
> Water pump and associated gaskets
> Timing Belt and associated bits (pulleys, etc.)
> Front Main Seal
> Cooling system flush (Zerex radiator super-flush)
> Oil/Filter
>
> Basically it's a whole top and front end refresh on a 1990 1.6L LWSC
> (VIN is in the 4000's somewhere) with the exception of the
> intake/exhaust gaskets and the valve seals. I will be working outside in
> a grassy gravel drive that is not level - the car will be on ramps
> rather than stands for safety reasons. I will lay out a tarp to catch
> the stray nut/bolt so they don't get lost in the rocks. I'm doing this
> redneck style! I even have a six pack of beer on standby.
>
> My question is thus:
>
> What is the best order to tackle this in?
>
> Obviously the cooling system is last. I am wondering things like - do I
> break the front pulley bolt before I remove the head and replace the
> front main seal before the head gasket, or do I reassemble the head and
> do the main later? Do I do the water pump on the way in or the way out?
> What (when) about the timing belt idler and tensioner?
>
> As a side note - I was planning on pulling the radiator (it'll be empty
> anyway) and remove the hood to do the work. Is this overkill or a good
> idea?
> FWIW - This will be my first time this deep into an engine. Conceptually
> I've got the process nailed down. I am generally mechanically inclined
> and technically savvy. I can read and write and set a torque wrench.
> Here's some things I don't know - are the head bolts deep well or
> standard sized sockets? Will I figure out a way to break the front
> pulley bolt? Can I get the front main out without gouging the crap out
> of the surfaces?
>
> I can follow instructions and can usually extrapolate missing/incomplete
> information..
> Speaking of which, I also ordered a signed copy of "Mazda Miata MX5,
> Performance Projects" by some guy named Keith Tanner. Being a
> tear-down/rebuild newbie it'll be a good playtest.
>
> Sorry for the novel of an email. I do plan on some photos and a blog of
> my journey - I'll post links when I get it started.
>
> Thanks in advance for answering the above - and thanks in advance for
> the panicked help I am about to ask for...
>
> Brad
> _______________________________________________
> Miatapower mailing list
> [email protected]
> http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
>
_______________________________________________
Miatapower mailing list
[email protected]
http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower

Reply via email to