What happens if you run a different window manager like fvwm? Den Tue, 20 Mar 2012 23:41:56 +0800 skrev Alan Cheng <bsdp...@gmail.com>:
> Hello List, > > So I'm using a Loongson YeeLoong netbook. I installed XFCE4 without > any issues, But it will freeze after around 15 minutes, even if I do > nothing on it. Starting "terminal" will cause it to freeze > immediately. > > I can still SSH into this netbook after freeze and everything else > seems to be fine. > > This happens back during 4.9 days. It's the same on 5.0 and current > snapshot. > > Any insight will be appreciated. and I'll be glad to provide any info > required to troubleshoot this. > > I'm not sure exactly what info will be needed, so I'll start with > dmesg. More will be provided as necessary: > > [ using 466480 bytes of bsd ELF symbol table ] > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights > reserved. Copyright (c) 1995-2012 OpenBSD. All rights reserved. > http://www.OpenBSD.org <http://www.openbsd.org/> > OpenBSD 5.1 (GENERIC) #93: Sun Feb 12 18:10:05 MST 2012 > dera...@loongson.openbsd.org:/usr/src/sys/arch/loongson/compile/GENERIC > real mem = 1073741824 (1024MB) > avail mem = 1059160064 (1010MB) > mainbus0 at root: Lemote Yeeloong > cpu0 at mainbus0: STC Loongson2F CPU 796 MHz, STC Loongson2F FPU > cpu0: cache L1-I 64KB D 64KB 4 way, L2 512KB 4 way > bonito0 at mainbus0: memory and PCI-X controller, rev 1 > pci0 at bonito0 bus 0 > rl0 at pci0 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address > 00:23:8b:b5:38:eb > rlphy0 at rl0 phy 0: RTL internal PHY > smfb0 at pci0 dev 8 function 0 "Silicon Motion LynxEM+" rev 0xb0 > wsdisplay0 at smfb0 mux 1: console (std, vt100 emulation) > ohci0 at pci0 dev 9 function 0 "NEC USB" rev 0x44: irq 7, version 1.0 > ehci0 at pci0 dev 9 function 1 "NEC USB" rev 0x05: irq 7 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1 > glxpcib0 at pci0 dev 14 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, > 32-bit 3579545Hz timer, watchdog, gpio > gpio1 at glxpcib0: 32 pins > pciide0 at pci0 dev 14 function 2 "AMD CS5536 IDE" rev 0x01: DMA, > channel 0 wired to compatibility, channel 1 wired to compatibility > wd0 at pciide0 channel 0 drive 0: <ST9160310AS> > wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > pciide0: channel 1 ignored (disabled) > auglx0 at pci0 dev 14 function 3 "AMD CS5536 Audio" rev 0x01: isa irq > 9, CS5536 AC97 > ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0) > audio0 at auglx0 > ohci1 at pci0 dev 14 function 4 "AMD CS5536 USB" rev 0x02: isa irq 11, > version 1.0, legacy support > ehci1 at pci0 dev 14 function 5 "AMD CS5536 USB" rev 0x02: isa irq 11 > usb1 at ehci1: USB revision 2.0 > uhub1 at usb1 "AMD EHCI root hub" rev 2.00/1.00 addr 1 > usb2 at ohci0: USB revision 1.0 > uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1 > isa0 at glxpcib0 > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > pms0 at pckbc0 (aux slot) > pckbc0: using irq 12 for aux slot > wsmouse0 at pms0 mux 0 > mcclock0 at isa0 port 0x70/2: mc146818 or compatible > ykbec0 at isa0 port 0x381/3 > usb3 at ohci1: USB revision 1.0 > uhub3 at usb3 "AMD OHCI root hub" rev 1.00/1.00 addr 1 > clock0 at mainbus0: ticker on int5 using count register > apm0 at mainbus0 > rum0 at uhub0 port 2 "Ralink Technology RT2573" rev 2.00/0.01 addr 2 > rum0: MAC/BBP RT2573 (rev 0x2573a), RF RT2528, address > 00:19:e0:81:e1:4e umass0 at uhub1 port 1 configuration 1 interface 0 > "Generic USB2.0-CRW" rev 2.00/58.87 addr 2 > umass0: using SCSI over Bulk-Only > scsibus0 at umass0: 2 targets, initiator 0 > sd0 at scsibus0 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 > 0/direct removable serial.0bda0158114173400000 > urtw0 at uhub1 port 4 "Realtek RTL8187B" rev 2.00/2.00 addr 3 > urtw0: RTL8187B rev E, address 00:17:c4:3d:33:f9 > vscsi0 at root > scsibus1 at vscsi0: 256 targets > softraid0 at root > scsibus2 at softraid0: 256 targets > pmon bootpath: /dev/disk/wd0 > boot device: wd0 > root on wd0a (2c517028a6b8deda.a) swap on wd0b dump on wd0b > apm0: battery high > > thanks, > Alan