fvwm works fine. So is jwm. Thanks, Alan On Tue, Mar 20, 2012 at 11:52 PM, Anders Trobdck <b...@troback.com> wrote:
> What happens if you run a different window manager like fvwm? > > Den Tue, 20 Mar 2012 23:41:56 +0800 > skrev Alan Cheng <bsdp...@gmail.com>: > > > Hello List, > > > > So I'm using a Loongson YeeLoong netbook. I installed XFCE4 without > > any issues, But it will freeze after around 15 minutes, even if I do > > nothing on it. Starting "terminal" will cause it to freeze > > immediately. > > > > I can still SSH into this netbook after freeze and everything else > > seems to be fine. > > > > This happens back during 4.9 days. It's the same on 5.0 and current > > snapshot. > > > > Any insight will be appreciated. and I'll be glad to provide any info > > required to troubleshoot this. > > > > I'm not sure exactly what info will be needed, so I'll start with > > dmesg. More will be provided as necessary: > > > > [ using 466480 bytes of bsd ELF symbol table ] > > Copyright (c) 1982, 1986, 1989, 1991, 1993 > > The Regents of the University of California. All rights > > reserved. Copyright (c) 1995-2012 OpenBSD. All rights reserved. > > http://www.OpenBSD.org <http://www.openbsd.org/> < > http://www.openbsd.org/> > > OpenBSD 5.1 (GENERIC) #93: Sun Feb 12 18:10:05 MST 2012 > > dera...@loongson.openbsd.org: > /usr/src/sys/arch/loongson/compile/GENERIC > > real mem = 1073741824 (1024MB) > > avail mem = 1059160064 (1010MB) > > mainbus0 at root: Lemote Yeeloong > > cpu0 at mainbus0: STC Loongson2F CPU 796 MHz, STC Loongson2F FPU > > cpu0: cache L1-I 64KB D 64KB 4 way, L2 512KB 4 way > > bonito0 at mainbus0: memory and PCI-X controller, rev 1 > > pci0 at bonito0 bus 0 > > rl0 at pci0 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address > > 00:23:8b:b5:38:eb > > rlphy0 at rl0 phy 0: RTL internal PHY > > smfb0 at pci0 dev 8 function 0 "Silicon Motion LynxEM+" rev 0xb0 > > wsdisplay0 at smfb0 mux 1: console (std, vt100 emulation) > > ohci0 at pci0 dev 9 function 0 "NEC USB" rev 0x44: irq 7, version 1.0 > > ehci0 at pci0 dev 9 function 1 "NEC USB" rev 0x05: irq 7 > > usb0 at ehci0: USB revision 2.0 > > uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1 > > glxpcib0 at pci0 dev 14 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, > > 32-bit 3579545Hz timer, watchdog, gpio > > gpio1 at glxpcib0: 32 pins > > pciide0 at pci0 dev 14 function 2 "AMD CS5536 IDE" rev 0x01: DMA, > > channel 0 wired to compatibility, channel 1 wired to compatibility > > wd0 at pciide0 channel 0 drive 0: <ST9160310AS> > > wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors > > wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > > pciide0: channel 1 ignored (disabled) > > auglx0 at pci0 dev 14 function 3 "AMD CS5536 Audio" rev 0x01: isa irq > > 9, CS5536 AC97 > > ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0) > > audio0 at auglx0 > > ohci1 at pci0 dev 14 function 4 "AMD CS5536 USB" rev 0x02: isa irq 11, > > version 1.0, legacy support > > ehci1 at pci0 dev 14 function 5 "AMD CS5536 USB" rev 0x02: isa irq 11 > > usb1 at ehci1: USB revision 2.0 > > uhub1 at usb1 "AMD EHCI root hub" rev 2.00/1.00 addr 1 > > usb2 at ohci0: USB revision 1.0 > > uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1 > > isa0 at glxpcib0 > > pckbc0 at isa0 port 0x60/5 > > pckbd0 at pckbc0 (kbd slot) > > pckbc0: using irq 1 for kbd slot > > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > > pms0 at pckbc0 (aux slot) > > pckbc0: using irq 12 for aux slot > > wsmouse0 at pms0 mux 0 > > mcclock0 at isa0 port 0x70/2: mc146818 or compatible > > ykbec0 at isa0 port 0x381/3 > > usb3 at ohci1: USB revision 1.0 > > uhub3 at usb3 "AMD OHCI root hub" rev 1.00/1.00 addr 1 > > clock0 at mainbus0: ticker on int5 using count register > > apm0 at mainbus0 > > rum0 at uhub0 port 2 "Ralink Technology RT2573" rev 2.00/0.01 addr 2 > > rum0: MAC/BBP RT2573 (rev 0x2573a), RF RT2528, address > > 00:19:e0:81:e1:4e umass0 at uhub1 port 1 configuration 1 interface 0 > > "Generic USB2.0-CRW" rev 2.00/58.87 addr 2 > > umass0: using SCSI over Bulk-Only > > scsibus0 at umass0: 2 targets, initiator 0 > > sd0 at scsibus0 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0 > > 0/direct removable serial.0bda0158114173400000 > > urtw0 at uhub1 port 4 "Realtek RTL8187B" rev 2.00/2.00 addr 3 > > urtw0: RTL8187B rev E, address 00:17:c4:3d:33:f9 > > vscsi0 at root > > scsibus1 at vscsi0: 256 targets > > softraid0 at root > > scsibus2 at softraid0: 256 targets > > pmon bootpath: /dev/disk/wd0 > > boot device: wd0 > > root on wd0a (2c517028a6b8deda.a) swap on wd0b dump on wd0b > > apm0: battery high > > > > thanks, > > Alan