I have this Same trouble with the Same ARC card. and I am using an intel Pentium D
the issue in my case is I must have a acpi enabled MP kernel, I did this by installing OpenBSD without the ARC controller in the system(I have a sata boot drive seprate from my RAID) then used config -ef /bsd.mp to enable acpi and disable apm then I mv /bsd.mp /bsd this fixed my issue. Sam Fourman Jr. On 7/19/07, Nick Humphrey <[EMAIL PROTECTED]> wrote: > > David Gwynne wrote: > > On Thu, Jul 19, 2007 at 12:29:51PM +0100, Nick Humphrey wrote: > >> I am having trouble with installing OpenBSD 4.1 on a new amd64 server > >> with an Areca ARC-1210 raid card. When I boot from the 4.1 CD install > >> media, everything seems fine up until it reaches" rd0: fixed, xxxx > >> blocks" and then the system hangs. I have downloaded the latest amd64 > >> current snapshot from the mirrors and tried booting from that too - > same > >> result. > >> > >> System: > >> - Gigabyte GA-M61PM-S2 (rev. 1.0) (BIOS Updated to latest F7 release) > >> - Areca ARC-1210 SATA RAID PCI-Express (firmware updated to V1.43 > >> 2007-04-17) > >> - 2 x 400GB SATA Disks > >> > >> I have setup RAID 1 mirror of the two disks in the RAID BIOS. (Areca > >> card and drives detected by and usable in Linux and Windows XP). > Without > >> the ARC-1210 card installed and the disks wired to the on-board SATA > >> controller everything works fine (i.e. I am able to install OpenBSD). I > >> have tried disabling on-board LAN and on-board SATA in the BIOS. I have > >> also tried enabling ACPI at boot time with ( -c, UKC> enable acpi, quit > >> ) which produces same result. In addition I have tried booting with the > >> i386 release media, and experienced exactly the same problem. > > > > can you show me a dmesg from this box with acpi enabled? > > > > dlg > > > > <snip> > > David, > > Please find below dmesg from 4.1-RELEASE with acpi enabled. > > Kind regards, > > Nick > > > boot> -c > booting cd0a:/4.1/amd64/bsd.rd: 2169728+438535+2270160+0+330160 > [80+220056+135431]=0x94f9a0 > entry point at 0x1001e0 [7205c766, 34000004, 24448b12, > 2840a304]* Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2007 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > OpenBSD 4.1 (RAMDISK_CD) #1054: Sat Mar 10 19:32:06 MST 2007 > [EMAIL PROTECTED]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD > real mem = 2079911936 (2031164K) > avail mem = 1778188288 (1736512K) > using 22937 buffers containing 208199680 bytes (203320K) of memory > User Kernel Config > UKC> enable acpi > 136 acpi0 enabled > UKC> quit > Continuing... > mainbus0 (root) > acpi0 at mainbus0: rev 0 > acpi0: tables DSDT FACP SSDT HPET MCFG APIC > acpiprt0 at acpi0: bus 0 (PCI0) > acpiprt1 at acpi0: bus 1 (HUB0) > cpu0 at mainbus0: (uniprocessor) > cpu0: AMD Athlon(tm) 64 X2 Dual Core Processor 5200+, 2612.33 MHz > cpu0: > > FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,CX16,NXE,MMXX,FFXSR,LONG,3DNOW2,3DNOW > cpu0: 64KB 64b/line 2-way I-cache, 64KB 64b/line 2-way D-cache, 1MB > 64b/line 16-way L2 cache > cpu0: ITLB 32 4KB entries fully associative, 8 4MB entries fully > associative > cpu0: DTLB 32 4KB entries fully associative, 8 4MB entries fully > associative > cpu0: PowerNow! K8 2612 MHz: speeds: 2600 2400 2200 2000 1800 1000 MHz > pci0 at mainbus0 bus 0: configuration mode 1 > "NVIDIA MCP61 Memory" rev 0xa1 at pci0 dev 0 function 0 not configured > "NVIDIA MCP61 ISA" rev 0xa2 at pci0 dev 1 function 0 not configured > "NVIDIA MCP61 SMBus" rev 0xa2 at pci0 dev 1 function 1 not configured > "NVIDIA MCP61 Memory" rev 0xa2 at pci0 dev 1 function 2 not configured > ohci0 at pci0 dev 2 function 0 "NVIDIA MCP61 USB" rev 0xa2: irq 10, > version 1.0, legacy support > usb0 at ohci0: USB revision 1.0 > uhub0 at usb0 > uhub0: NVIDIA OHCI root hub, rev 1.00/1.00, addr 1 > uhub0: 10 ports with 10 removable, self powered > ehci0 at pci0 dev 2 function 1 "NVIDIA MPC61 USB" rev 0xa2: irq 11 > usb1 at ehci0: USB revision 2.0 > uhub1 at usb1 > uhub1: NVIDIA EHCI root hub, rev 2.00/1.00, addr 1 > uhub1: 10 ports with 10 removable, self powered > ppb0 at pci0 dev 4 function 0 "NVIDIA MCP61" rev 0xa1 > pci1 at ppb0 bus 1 > skc0 at pci1 dev 7 function 0 "D-Link Systems DGE-530T B1" rev 0x11, > Yukon Lite (0x9): irq 10 > sk0 at skc0 port A, address 00:15:e9:aa:d3:34 > eephy0 at sk0 phy 0: Marvell 88E1011 Gigabit PHY, rev. 5 > pciide0 at pci0 dev 6 function 0 "NVIDIA MCP61 IDE" rev 0xa2: DMA, > channel 0 configured to compatibility, channel 1 configured to > compatibility > atapiscsi0 at pciide0 channel 0 drive 0 > scsibus0 at atapiscsi0: 2 targets > cd0 at scsibus0 targ 0 lun 0: <_NEC, DVD_RW ND-2510A, 2.16> SCSI0 > 5/cdrom removable > cd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 > pciide0: channel 1 ignored (disabled) > ppb1 at pci0 dev 9 function 0 "NVIDIA MCP61 PCIE" rev 0xa2 > pci2 at ppb1 bus 2 > ppb2 at pci2 dev 0 function 0 "Intel IOP332 PCIE-PCIX" rev 0x07 > pci3 at ppb2 bus 3 > arc0 at pci3 dev 14 function 0 "Areca ARC-1210" rev 0x00: irq 11 > arc0: 4 SATA Ports, 256MB SDRAM, FW Version: V1.43 2007-4-17 > scsibus1 at arc0: 16 targets > sd0 at scsibus1 targ 0 lun 0: <Areca, ARC-1210-VOL#00, R001> SCSI3 > 0/direct fixed > sd0: 381469MB, 58128 cyl, 28 head, 480 sec, 512 bytes/sec, 781249536 sec > total > ppb3 at pci2 dev 0 function 2 "Intel IOP332 PCIE-PCIX" rev 0x07 > pci4 at ppb3 bus 4 > vga1 at pci0 dev 13 function 0 "NVIDIA GeForce 6100 nForce 430" rev 0xa2 > wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) > pchb0 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00 > pchb1 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00 > pchb2 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00 > pchb3 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00 > isa0 at mainbus0 > com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo > com0: console > com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo > pckbc0 at isa0 port 0x60/5 > pckbd0 at pckbc0 (kbd slot) > pckbc0: using irq 1 for kbd slot > wskbd0 at pckbd0: console keyboard, using wsdisplay0 > rd0: fixed, 3584 blocks > > -------------------------------------------------------------- > > End.
