[I read all postings in the archive AFAIK]
Just started with CF on embedded hardware advertised to run OpenBSD;
ARInfoTek. It does run OpenBSD very well!
Now I want the embedded system to run off CF; the board has a CF socket
to be wd0.
4.2 runs out of the box, but with very slow access of files. The CF is
reasonably fast, though, with ~6MB at 'dd'. But once it has to access
files for r/w, it gets very slow.
I found some postings that 4.3 would be better, but the install of 4.3
here mainly -stalled- and took a good hour, from a local ftp-site.
locate.updatedb is incredibly fast, while some file extraction takes ages.
It looks like a large, single, file copies very fast, similar to 'dd'.
But opening a file for r/w seems to take ages. Something like
tar -C /tmp -xzphf etc43.tgz
takes a minute, easily. And etc43.tgz is only 1.2MB.
Copying of this file is quick:
$ date && cp etc43.tgz demo && date
Mon Oct 20 11:29:15 SGT 2008
Mon Oct 20 11:29:16 SGT 2008
Any hint welcome,
Uwe
OpenBSD 4.3 (GENERIC) #698: Wed Mar 12 11:07:05 MDT 2008
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 500
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 527785984 (503MB)
avail mem = 502276096 (479MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 05/23/08, BIOS32 rev. 0 @ 0xfaf00
apm0 at bios0: Power Management spec V1.2 (slowidle)
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdb74
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdaf0/128 (6 entries)
pcibios0: PCI Exclusive IRQs: 5 7 10 11
pcibios0: no compatible PCI ICU found: ICU vendor 0x1022 product 0x2090
pcibios0: Warning, unable to fix up PCI interrupt routing
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xef000/0x1000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x31
vga1 at pci0 dev 1 function 1 "AMD Geode LX Video" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 0, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <ULTIMATE CF CARD 4GB>
wd0: 1-sector PIO, LBA, 3967MB, 8124480 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 7, version 1.0,
legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
ppb0 at pci0 dev 18 function 0 "Pericom PCI-PCI" rev 0x00
pci1 at ppb0 bus 1
fxp0 at pci1 dev 12 function 0 "Intel 82559ER" rev 0x10, i82551: irq 5, address
00:14:b7:00:26:6a
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
fxp1 at pci1 dev 13 function 0 "Intel 82559ER" rev 0x10, i82551: irq 11,
address 00:14:b7:00:26:6b
inphy1 at fxp1 phy 1: i82555 10/100 PHY, rev. 4
fxp2 at pci1 dev 14 function 0 "Intel 82559ER" rev 0x10, i82551: irq 10,
address 00:14:b7:00:26:6c
inphy2 at fxp2 phy 1: i82555 10/100 PHY, rev. 4
fxp3 at pci0 dev 19 function 0 "Intel 82559ER" rev 0x10, i82551: irq 11,
address 00:14:b7:00:26:69
inphy3 at fxp3 phy 1: i82555 10/100 PHY, rev. 4
isa0 at glxpcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbdprobe: reset response 0xfa
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask f3cf netmask ffef ttymask ffef
mtrr: K6-family MTRR support (2 registers)
uplcom0 at uhub1 port 1 "Prolific Technology Inc. USB-Serial Controller" rev
1.10/3.00 addr 2
ucom0 at uplcom0
uhidev0 at uhub1 port 2 configuration 1 interface 0 "NOVATEK USB Multimedia
Keyboard" rev 1.10/1.00 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes, country code 33
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub1 port 2 configuration 1 interface 1 "NOVATEK USB Multimedia
Keyboard" rev 1.10/1.00 addr 3
uhidev1: iclass 3/0, 3 report ids
uhid0 at uhidev1 reportid 2: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=3, output=0, feature=0
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
