Hey Folks,
I've been pulling my hair out on this one for a little while now, I have
a 4.7 AMD64 release firewall based around an Intel D945GCLF using the
on-board 8101E based Realtek Nic which is connected to a Netgear
FSM726v1 L2 Managed switch.
I've been trying to configure the Firewall/Switch to run multiple .1q
vlans over the single interface without any luck. Configs listed below.
So in a fit of desperation I pulled out an old Nokia IP440, installed
4.8 i386 release and configured up the 'same' vlan interface, the Nokia
uses the dc nic driver. In this configuration with this device the
tagging works!
Both devices where plugged into the same port on the switch, the
configuration of which wasn't changed.
So my question is this, is the problem with 4.7AMD64 the Realtek Nic or
the Intel D945GCLF board? Given the teething problems of BSD of the
Intel board I suspect its this but thought I'd try and save myself the
time in re-installing etc if someone in the know could point out whats
fubar'd.
Cheers guys, 4.8 yet another fantastic release ;)
Simon
Non working D945GCLF
# cat /etc/hostname.re0
up
# cat /etc/hostname.vlan11
inet 11.0.0.199 255.255.255.0 11.0.0.255 vlan 11 vlandev re0
Working Nokia IP440
# cat /etc/hostname.dc0
up
# cat /etc/hostname.vlan11
inet 11.0.0.199 255.255.255.0 11.0.0.255 vlan 11 vlandev dc0
Switch Config (FSM726 firmware 2.6.5):
interface Ethernet 1/1
cos normal
description Not Defined
no shutdown
speed 100
duplex full
flow-ctrl
negotiation auto
broadcast-rate 3000
dot1x port-control authorized
no mac-lockdown
no switchport access vlan 1
switchport access vlan tagged 11
switchport access native 11
no mirror
spanning-tree port-priority 128
spanning-tree cost 19
spanning-tree fastlink
exit
Intel Board:
OpenBSD 4.7 (GENERIC) #112: Wed Mar 17 20:43:49 MDT 2010
dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC
real mem = 2135109632 (2036MB)
avail mem = 2068836352 (1972MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.4 @ 0xe3590 (23 entries)
bios0: vendor Intel Corp. version "LF94510J.86A.0038.2008.0427.2223"
date 04/27/2008
bios0: Intel Corporation D945GCLF
acpi0 at bios0: rev 0
acpi0: tables DSDT FACP APIC WDDT MCFG ASF!
acpi0: wakeup devices SLPB(S4) P32_(S4) UAR1(S4) UAR2(S4) PEX0(S4)
PEX1(S4) PEX2(S4) PEX3(S4) PEX4(S4) PEX5(S4) UHC1(S3) UHC2(S3) UHC3(S3)
UHC4(S3) EHCI(S3) AC9M(S4) AZAL(S4)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Atom(TM) CPU 230 @ 1.60GHz, 1596.34 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,SSE3,MWAIT,DS-CPL,TM2,CX16,xTPR,NXE,LONG
cpu0: 512KB 64b/line 16-way L2 cache
cpu0: apic clock running at 133MHz
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0, remapped to apid 2
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 4 (P32_)
acpiprt2 at acpi0: bus 1 (PEX0)
acpiprt3 at acpi0: bus -1 (PEX1)
acpiprt4 at acpi0: bus 2 (PEX2)
acpiprt5 at acpi0: bus 3 (PEX3)
acpiprt6 at acpi0: bus -1 (PEX4)
acpiprt7 at acpi0: bus -1 (PEX5)
acpicpu0 at acpi0
acpibtn0 at acpi0: SLPB
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 82945G Host" rev 0x02
vga1 at pci0 dev 2 function 0 "Intel 82945G Video" rev 0x02
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
intagp0 at vga1
agp0 at intagp0: aperture at 0x80000000, size 0x10000000
inteldrm0 at vga1: apic 2 int 16 (irq 11)
drm0 at inteldrm0
ppb0 at pci0 dev 28 function 0 "Intel 82801GB PCIE" rev 0x01: apic 2 int
17 (irq 255)
pci1 at ppb0 bus 1
re0 at pci1 dev 0 function 0 "Realtek 8101E" rev 0x02: RTL8102EL
(0x2480), apic 2 int 16 (irq 11), address 00:1c:c0:45:3e:65
rlphy0 at re0 phy 7: RTL8201L 10/100 PHY, rev. 1
ppb1 at pci0 dev 28 function 2 "Intel 82801GB PCIE" rev 0x01: apic 2 int
18 (irq 255)
pci2 at ppb1 bus 2
ppb2 at pci0 dev 28 function 3 "Intel 82801GB PCIE" rev 0x01: apic 2 int
19 (irq 255)
pci3 at ppb2 bus 3
uhci0 at pci0 dev 29 function 0 "Intel 82801GB USB" rev 0x01: apic 2 int
23 (irq 9)
uhci1 at pci0 dev 29 function 1 "Intel 82801GB USB" rev 0x01: apic 2 int
19 (irq 10)
uhci2 at pci0 dev 29 function 2 "Intel 82801GB USB" rev 0x01: apic 2 int
18 (irq 11)
uhci3 at pci0 dev 29 function 3 "Intel 82801GB USB" rev 0x01: apic 2 int
16 (irq 11)
ehci0 at pci0 dev 29 function 7 "Intel 82801GB USB" rev 0x01: apic 2 int
23 (irq 9)
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xe1
pci4 at ppb3 bus 4
pcib0 at pci0 dev 31 function 0 "Intel 82801GB LPC" rev 0x01
pciide0 at pci0 dev 31 function 2 "Intel 82801GB SATA" rev 0x01: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 2 int 19 (irq 10) for native-PCI interrupt
wd0 at pciide0 channel 0 drive 0: <WDC WD1600BEKT-00A25T0>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
ichiic0 at pci0 dev 31 function 3 "Intel 82801GB SMBus" rev 0x01: apic 2
int 19 (irq 10)
iic0 at ichiic0
admtm0 at iic0 addr 0x2d: 47m192
spdmem0 at iic0 addr 0x50: 2GB DDR2 SDRAM non-parity PC2-5300CL5
usb1 at uhci0: USB revision 1.0
uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb2 at uhci1: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci2: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci3: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
mtrr: Pentium Pro MTRR support
uhidev0 at uhub4 port 1 configuration 1 interface 0 " USB Keyboard" rev
1.10/2.80 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub4 port 1 configuration 1 interface 1 " USB Keyboard" rev
1.10/2.80 addr 2
uhidev1: iclass 3/0, 2 report ids
uhid0 at uhidev1 reportid 1: input=1, output=0, feature=0
uhid1 at uhidev1 reportid 2: input=3, output=0, feature=0
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
Nokia IP440
OpenBSD 4.8 (GENERIC) #136: Mon Aug 16 09:06:23 MDT 2010
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium III ("GenuineIntel" 686-class) 599 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PSE36,SER,MMX,FXSR,SSE
real mem = 267993088 (255MB)
avail mem = 253652992 (241MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 02/23/00, BIOS32 rev. 0 @ 0xfd7a0,
SMBIOS rev. 2.1 @ 0xefbe0 (42 entries)
bios0: vendor Intel Corp. version "4S4EB2X0.86A.0023.P16" date 02/23/2000
bios0: Intel Corporation SE440BX-2
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S5
acpi0: tables DSDT FACP
acpi0: wakeup devices PCI0(S1) USB0(S1) UAR1(S1) UAR2(S1) KBC_(S1) MICE(S1)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpiprt0 at acpi0: bus 0 (PCI0)
acpicpu0 at acpi0: C3, C2
acpipwrres0 at acpi0: PFAN
bios0: ROM list: 0xc0000/0x8000 0xe0000/0x4000! 0xe4000/0xc000
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x03
intelagp0 at pchb0
agp0 at intelagp0: aperture at 0xf8000000, size 0x4000000
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Mach64" rev 0x27
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
piixpcib0 at pci0 dev 7 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 7 function 1 "Intel 82371AB IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IC35L020AVER07-0>
wd0: 16-sector PIO, LBA, 19623MB, 40188960 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <TEAC, CD-540E, 1.0A> ATAPI 5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "Intel 82371AB USB" rev 0x01: irq 9
piixpm0 at pci0 dev 7 function 3 "Intel 82371AB Power" rev 0x02: SMI
iic0 at piixpm0
lmenv0 at iic0 addr 0x2d: adm9240 rev 2, starting scan
spdmem0 at iic0 addr 0x50: 128MB SDRAM ECC PC100CL2
spdmem1 at iic0 addr 0x51: 128MB SDRAM ECC PC100CL2
ppb1 at pci0 dev 13 function 0 "DEC 21152 PCI-PCI" rev 0x03
pci2 at ppb1 bus 2
dc0 at pci2 dev 4 function 0 "DEC 21142/3" rev 0x41: irq 11, address
00:c0:95:e0:9d:1c
dcphy0 at dc0 phy 31: internal PHY
dc1 at pci2 dev 5 function 0 "DEC 21142/3" rev 0x41: irq 10, address
00:c0:95:e0:9d:1d
dcphy1 at dc1 phy 31: internal PHY
dc2 at pci2 dev 6 function 0 "DEC 21142/3" rev 0x41: irq 7, address
00:c0:95:e0:9d:1e
dcphy2 at dc2 phy 31: internal PHY
dc3 at pci2 dev 7 function 0 "DEC 21142/3" rev 0x41: irq 9, address
00:c0:95:e0:9d:1f
dcphy3 at dc3 phy 31: internal PHY
isa0 at piixpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "Intel UHCI root hub" rev 1.00/1.00 addr 1
biomask f36d netmask ffed ttymask ffff
mtrr: Pentium Pro MTRR support
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
