--- Myth Lists wrote: > Ben Dash wrote: > >I try the ~/.mythtv/lircrc file and let you know. > > > >I'm using the atiusb driver for lirc. I heard that > >this was supposed to work for the xBox remote, is > that > >correct? > Well, Xebian comes pre-configured with a kernel > module for myth. I've > tarr'd up my /etc/lirc directory so you can get the > config file for your > remote. Not sure about the kernel module -- I > didn't build it so not > sure.
It looks like I was not supposed to be using atiusb as my lirc driver. xboxusb seems to be loading better, see dmesg output snippet below: lirc_dev: IR Remote Control driver registered, at major 61 usbcore: registered new driver usbfs usbcore: registered new driver hub lirc_xbox: XBOX USB remote driver for LIRC v0.3 usbcore: registered new driver lirc_xbox FATX: 0.0.3 Adding 262136k swap on /mnt/fatx/E/linuxswap. Priority:-1 extents:2 Real Time Clock Driver v1.12 ohci_hcd: 2004 Nov 08 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) PCI: Setting latency timer of device 0000:00:02.0 to 64 ohci_hcd 0000:00:02.0: OHCI Host Controller ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:02.0: irq 1, io mem 0xfed00000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 4 ports detected PCI: Setting latency timer of device 0000:00:03.0 to 64 ohci_hcd 0000:00:03.0: OHCI Host Controller ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:03.0: irq 9, io mem 0xfed08000 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usb 1-1: new full speed USB device using ohci_hcd and address 2 hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing disabled PCI: Enabling device 0000:00:06.1 (0000 -> 0003) PCI: No IRQ known for interrupt pin B of device 0000:00:06.1. Please try using pci=biosirq. usb 1-1.1: new full speed USB device using ohci_hcd and address 3 lirc_dev: lirc_register_plugin:sample_rate: 0 lirc_xbox[3]: Xbox IR on usb1:3 I have a /etc/lircd.conf which appears to be set up for xbox: # # this config file was automatically generated # using WinLIRC 0.6.4 (LIRC 0.6.1pre3) on Tue May 06 20:57:47 2003 # # contributed by # # brand: MicroSoft # model: Xbox remote # supported devices: Xbox # begin remote name xbox ... end remote Where is the lircrc file supposed to go? ~/lircrc ~/.lircrc ~/.mythtv/lircrc ~/.mythtv/.lircrc None of those locations seemed to make any difference, no response from the xBox DVD remote. I tried running mode2, since irw never seemded to do anything except say "connect: Connection refused" and it complained "mode2: error opening /dev/lirc" and indeed it doesn't exist: [EMAIL PROTECTED] ~ $ ls -la /dev/lir* srw-rw-rw- 1 root root 0 Nov 1 00:02 /dev/lircd Do I need to create a lirc device manually? Please let me know any ideas, Thanks, Ben ----------------------------------------------------- | o | | _ /<_ | |(_)>(_) | |Ben Dash | |Ask free questions - http://bensqanda.blogspot.com | |My Blog - http://bensdailythoughts.blogspot.com | |Info - http://bensinformationstation.blogspot.com | |Workouts - http://bensworkouts.blogspot.com | ----------------------------------------------------- __________________________________ Yahoo! Mail - PC Magazine Editors' Choice 2005 http://mail.yahoo.com _______________________________________________ mythtv-users mailing list mythtv-users@mythtv.org http://mythtv.org/cgi-bin/mailman/listinfo/mythtv-users