Hey dave I have some left over cable from when I extended my power supply runs. If your interested I can dig it out and let you know what I have.
Take care, Jared -----Original Message----- >From: [email protected] >Sent: Apr 2, 2010 4:10 PM >To: [email protected] >Subject: Re: NEOTEK: EDAC Connections > >Ike, > I hooked everything up according to your code using the black/grey >wire for black/white and fired it up. I'm playing CDs back through >tape 1 right now. It sounds great. The VU meters aren't lighting up >or doing anything. I've only got one power supply. The sticker on the >back says PS-2. There's a slight hum coming from the supply, but >that's probably natural. Is it possible to get a longer supply cable >so I can put it in another room? > >Thanks, >Dave > >---- Original Message ---- >From: [email protected] >To: [email protected] >Subject: Re: NEOTEK: EDAC Connections >Date: Fri, 02 Apr 2010 14:37:28 -0400 > >>Hi David, >> 1st off, I /believe/ that the color code that I gave you was the >> >>Neotek "standard". However, I haven't seen this written down many >>places, so I also believe that whoever hooked up may of these >>supplies >>just made it up as they went along. >> 2nd, the black/gray is the same as the black/white >> 3rd, as long as each wire goes to the same terminal at each end >>the >>color doesn't really matter. HOWEVER, I think it would be a good idea >>if >>you made the color code match what I sent you. >> By the way, you mentioned that this is a 40 channel desk...do >>you >>have one power supply, or two? >>best, >>Ike >> >> >>On 4/2/2010 12:28 PM, [email protected] wrote: >>> I'm finding some inconsistencies with the power supply/console >>> wiring. The way the wiring came connected on the power supply is >>> listed below. My supply cable has a black wire with grey stripes >>> connected to the Bi Polar Ground (maybe this wire is considered the >>> "black/white" wire?). Here's how I received the power supply with >>the >>> supply cable already connected to it: >>> >>> TOP ROW: >>> -18v..................Blue >>> -18v..................Blue/Black >>> Bi polar Ground.......Black >>> Bi Polar Ground.......Black/Grey (black/white?) >>> +18v..................Red >>> +18v..................Red/Black >>> >>> BOTTOM ROW: >>> >>> +48v..................Green >>> Phantom Ground........Green/Black >>> +35v..................White >>> Meter Ground..........White/Black >>> -25v..................Orange >>> Logic Ground..........Orange/Black >>> >>> The Black/Grey wire is confusing me, as well as the green wire >>which >>> is connected to the +48V terminal (Ike, you mentioned that the +48v >>> should be white). Any ideas? >>> >>> >>> >>> ---- Original Message ---- >>> From: [email protected] >>> To: [email protected] >>> Subject: Re: NEOTEK: EDAC Connections >>> Date: Wed, 31 Mar 2010 09:52:26 -0400 >>> >>> >>>> Here's an idea: why not build some DB-25 to 1/4" snakes to adapt >>the >>>> >>>> existing PT cables? That way you don't have to touch the edac end, >>>> and >>>> you will be able to interface with most recording devices, now and >>in >>>> >>>> the future. >>>> Best >>>> Ike >>>> >>>> Sent from my iPhone >>>> >>>> On 2010-03-30, at 5:40 PM, [email protected] wrote: >>>> >>>> >>>>> Ike, >>>>> All of the cable snakes have edac connectors on the board end. >>I >>>>> have 2 HD24XR machines that only accept 1/4" plugs, so I'll have >>to >>>>> change those over. I'm going to take it slow and tackle the >>>>> connections as I go. I may have to make some changes on the >>>>> multitrack returns at the board, in which case I'll probably need >>>>> >>>> to >>>> >>>>> figure out the pin layout so I can return signal to all 40 >>channels >>>>> if I need to. The board is 40x26x8. >>>>> >>>>> Dave >>>>> >>>>> ---- Original Message ---- >>>>> From: [email protected] >>>>> To: [email protected] >>>>> Subject: Re: NEOTEK: Power Supply Connections >>>>> Date: Tue, 30 Mar 2010 12:31:22 -0400 >>>>> >>>>> >>>>>> Hi David >>>>>> If your edac cons already have cable in them you should >>only >>>>>> have to re- terminate the other end (don't the Alesis decks use >>a >>>>>> >>>> 56 >>>> >>>>>> pin edac for I/O)? >>>>>> In any case edac product including pins and tooling are >>>>>> available from digi-key and others. >>>>>> Reverb 1-4 is probably the Aux 1-4 sends that you would >>plug >>>>>> >>>>>> into your fx units. >>>>>> Best >>>>>> Ike >>>>>> >>>>>> Sent from my iPhone >>>>>> >>>>>> On 2010-03-30, at 11:09 AM, [email protected] wrote: >>>>>> >>>>>> >>>>>>> Thanks again Ike, >>>>>>> I've got an edac snake for the master section. The snake is >>>>>>> >>>>>> labled >>>>>> >>>>>>> like this: >>>>>>> >>>>>>> Cue 1& 2 In L-R >>>>>>> >>>>> >>>> ------ >>>> >>>> View the list online at: >>>> http://www.mail-archive.com/[email protected] >>>> >>>> You can unsubscribe at anytime by sending an email to >>>> mailto:[email protected] with "unsubscribe neotek" in the >>>> message body. If you have any difficulties, or questions --please >>>> send an email to mailto:[email protected]. >>>> >>>> The Neotek list is lovingly hosted by Catapult Web. Remember that >>any >>>> message or reply sent to the list will be automatically forwarded >>to >>>> all subscribers. >>>> >>>> Vive Le Neotek! >>>> >>>> Thanks. >>>> >>> >>> ------ >>> >>> View the list online at: >>http://www.mail-archive.com/[email protected] >>> >>> You can unsubscribe at anytime by sending an email to >>mailto:[email protected] with "unsubscribe neotek" in the >>message body. If you have any difficulties, or questions --please >>send an email to mailto:[email protected]. >>> >>> The Neotek list is lovingly hosted by Catapult Web. Remember that >>any message or reply sent to the list will be automatically forwarded >>to all subscribers. >>> >>> Vive Le Neotek! >>> >>> Thanks. >>> >>> >>> >> >>-- >>Ike Zimbel >>Zimbel Audio Productions Ltd. >>Toronto >>416-720-0887 >> >>"Studio House Calls". Authorized Warranty service for Allen& Heath, >>Clear-Com, Drawmer, Soundcraft, SPL and Yamaha. Repairs and upgrades >>to >>analog audio equipment including: AMEK, dbx, Neve, Neotek, MCI, >>Soundcraft and more. Ask about our RF Frequency co-ordination >>services! >>www.zimbelaudio.com >> >>------ >> >>View the list online at: >>http://www.mail-archive.com/[email protected] >> >>You can unsubscribe at anytime by sending an email to >>mailto:[email protected] with "unsubscribe neotek" in the >>message body. If you have any difficulties, or questions --please >>send an email to mailto:[email protected]. >> >>The Neotek list is lovingly hosted by Catapult Web. Remember that any >>message or reply sent to the list will be automatically forwarded to >>all subscribers. >> >>Vive Le Neotek! >> >>Thanks. > > >------ > >View the list online at: http://www.mail-archive.com/[email protected] > >You can unsubscribe at anytime by sending an email to >mailto:[email protected] with "unsubscribe neotek" in the message body. >If you have any difficulties, or questions --please send an email to >mailto:[email protected]. > >The Neotek list is lovingly hosted by Catapult Web. Remember that any message >or reply sent to the list will be automatically forwarded to all subscribers. > >Vive Le Neotek! > >Thanks. ------ View the list online at: http://www.mail-archive.com/[email protected] You can unsubscribe at anytime by sending an email to mailto:[email protected] with "unsubscribe neotek" in the message body. If you have any difficulties, or questions --please send an email to mailto:[email protected]. The Neotek list is lovingly hosted by Catapult Web. Remember that any message or reply sent to the list will be automatically forwarded to all subscribers. Vive Le Neotek! Thanks.
