On Fri, 20 Jan 2017 21:46:51 -0800 Roopa Prabhu <ro...@cumulusnetworks.com> wrote:
> From: Roopa Prabhu <ro...@cumulusnetworks.com> > > High level summary: > lwt and dst_metadata/collect_metadata have enabled vxlan l3 deployments > to use a single vxlan netdev for multiple vnis eliminating the scalability > problem with using a single vxlan netdev per vni. This series tries to > do the same for vxlan netdevs in pure l2 bridged networks. > Use-case/deployment and details are below. > > Deployment scerario details: > As we know VXLAN is used to build layer 2 virtual networks across the > underlay layer3 infrastructure. A VXLAN tunnel endpoint (VTEP) > originates and terminates VXLAN tunnels. And a VTEP can be a TOR switch > or a vswitch in the hypervisor. This patch series mainly > focuses on the TOR switch configured as a Vtep. Vxlan segment ID (vni) > along with vlan id is used to identify layer 2 segments in a vxlan > overlay network. Vxlan bridging is the function provided by Vteps to terminate > vxlan tunnels and map the vxlan vni to traditional end host vlan. This is > covered in the "VXLAN Deployment Scenarios" in sections 6 and 6.1 in RFC 7348. > To provide vxlan bridging function, a vtep has to map vlan to a vni. The rfc > says that the ingress VTEP device shall remove the IEEE 802.1Q VLAN tag in > the original Layer 2 packet if there is one before encapsulating the packet > into the VXLAN format to transmit it through the underlay network. The remote > VTEP devices have information about the VLAN in which the packet will be > placed based on their own VLAN-to-VXLAN VNI mapping configurations. > > Existing solution: > Without this patch series one can deploy such a vtep configuration by > by adding the local ports and vxlan netdevs into a vlan filtering bridge. > The local ports are configured as trunk ports carrying all vlans. > A vxlan netdev per vni is added to the bridge. Vlan mapping to vni is > achieved by configuring the vlan as pvid on the corresponding vxlan netdev. > The vxlan netdev only receives traffic corresponding to the vlan it is mapped > to. This configuration maps traffic belonging to a vlan to the corresponding > vxlan segment. > > ----------------------------------- > | bridge | > | | > ----------------------------------- > |100,200 |100 (pvid) |200 (pvid) > | | | > swp1 vxlan1000 vxlan2000 > > This provides the required vxlan bridging function but poses a > scalability problem with using a single vxlan netdev for each vni. > > Solution in this patch series: > The Goal is to use a single vxlan device to carry all vnis similar > to the vxlan collect metadata mode but vxlan driver still carrying all > the forwarding information. > - vxlan driver changes: > - enable collect metadata mode device to be used with learning, > replication, fdb > - A single fdb table hashed by (mac, vni) > - rx path already has the vni > - tx path expects a vni in the packet with dst_metadata and vxlan > driver has all the forwarding information for the vni in the > dst_metadata. > > - Bridge driver changes: per vlan LWT and dst_metadata support: > - Our use case is vxlan and 1-1 mapping between vlan and vni, but I have > kept the api generic for any tunnel info > - Uapi to configure/unconfigure/dump per vlan tunnel data > - new bridge port flag to turn this feature on/off. off by default > - ingress hook: > - if port is a lwt tunnel port, use tunnel info in > attached dst_metadata to map it to a local vlan > - egress hook: > - if port is a lwt tunnel port, use tunnel info attached to vlan > to set dst_metadata on the skb > > Other approaches tried and vetoed: > - tc vlan push/pop and tunnel metadata dst: > - posses a tc rule scalability problem (2 rules per vni) > - cannot handle the case where a packet needs to be replicated to > multiple vxlan remote tunnel end-points.. which the vxlan driver > can do today by having multiple remote destinations per fdb. > - making vxlan driver understand vlan-vni mapping: > - I had a series almost ready with this one but soon realized > it duplicated a lot of vlan handling code in the vxlan driver > > This series is briefly tested for functionality. Sending it out as RFC while > I continue to test it more. There are some rough edges which I am in the > process > of fixing. > > Signed-off-by: Roopa Prabhu <ro...@cumulusnetworks.com> > > Roopa Prabhu (5): > ip_tunnels: new IP_TUNNEL_INFO_BRIDGE flag for ip_tunnel_info mode > vxlan: make COLLECT_METADATA mode bridge friendly > bridge: uapi: add per vlan tunnel info > bridge: vlan lwt and dst_metadata netlink support > bridge: vlan lwt dst_metadata hooks in ingress and egress paths > > drivers/net/vxlan.c | 209 ++++++++++++-------- > include/linux/if_bridge.h | 1 + > include/net/ip_tunnels.h | 1 + > include/uapi/linux/if_bridge.h | 11 ++ > include/uapi/linux/if_link.h | 1 + > include/uapi/linux/neighbour.h | 1 + > net/bridge/br_input.c | 5 + > net/bridge/br_netlink.c | 410 > ++++++++++++++++++++++++++++++++++------ > net/bridge/br_private.h | 22 +++ > net/bridge/br_vlan.c | 193 ++++++++++++++++++- > 10 files changed, 717 insertions(+), 137 deletions(-) > Yes this is a complex issue, but I am concerned about the added code bloat and complexity. The bridge which is already a mess with netfilter, multicast, vlan filtering etc.The current code not modular and grows with each feature. At the same time, the same bridge functionality is used in its simplest form by all the network virtualization and container technolgies. Maybe do it in OpenVswitch or figure out a way to do customization with BPF? more complex than it should
