From: "Mikkel L. Ellertson" <[EMAIL PROTECTED]>
To: <[email protected]>
Sent: Monday, June 20, 2005 9:29 PM
Subject: Re: [newbie] mdkcustom missing
Teilhard Knight wrote:
Of course I thought in doing what you say. Problem is that MCC does not
detect my device. It asks me to load a driver by hand without more
options. I have checked with "lsmod" that my module is loaded, but the
device does not show up. HardDrake detects it as "other devices" and
UsbView detects it quite nicely, as if it was a device just ready to
use. Any ideas?
Teilhard.
If it is not being detected as a NIC, then you are going to have
problems with more then just MCC...
Dumb question time:
Did you run "depmod -a" or reboot after building the module? This is
needed to update the list hotplug uses for loading modules when devices
are plugged in. (If it was plugged in when you updated things, then you
will need to unplug it, and plug it in again.)
No, I didn't do it, but I have done it already without the device plugged,
and I have plugged it a nothing has changed.
You may also want to take a look at /proc/bus/usb/devices and see if a
driver is being loaded for the device. Or you can post the output of:
cat /proc/bus/usb/devices
and we can help you decode it. It sounds like the driver is not being
tied to the NIC, and so no Ethernet device is being created. Without
that, none of the network commands are going to work.
It seems the driver loads all right as far as I can gather. But I gibve you
the file so you can see the otcome.
--------------------------
T: Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 8
B: Alloc= 0/800 us ( 0%), #Int= 1, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.8.1-12mdksmp ehci_hcd
S: Product=EHCI Host Controller
S: SerialNumber=0000:00:1d.7
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=256ms
T: Bus=05 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 8 Spd=480 MxCh= 1
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2515 Rev= 0.01
S: Manufacturer=USB 2.0 Flash Disk
S: Product=USB Embedded Hub
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 1 Ivl=256ms
T: Bus=05 Lev=02 Prnt=08 Port=00 Cnt=01 Dev#= 9 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=067b ProdID=2517 Rev= 0.01
S: Manufacturer=USB 2.0 Flash Disk
S: Product=USB Mass Storage Device
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=05 Lev=01 Prnt=01 Port=05 Cnt=02 Dev#= 10 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ff(vend.) Sub=ff Prot=ff MxPS=64 #Cfgs= 1
P: Vendor=0ace ProdID=1211 Rev=43.30
S: Manufacturer=ZyDAS
S: Product=USB2.0 WLAN
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 4 Cls=ff(vend.) Sub=00 Prot=00 Driver=zd1211
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=04(O) Atr=03(Int.) MxPS= 64 Ivl=125us
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.8.1-12mdksmp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.3
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=04 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=058f ProdID=9360 Rev= 1.00
S: Manufacturer=
S: Product=USB Reader
S: SerialNumber=9205291
C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.8.1-12mdksmp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.2
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc=236/900 us (26%), #Int= 2, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.8.1-12mdksmp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.1
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=03f0 ProdID=050c Rev= 2.40
S: Manufacturer=BTC
S: Product=USB Multimedia Cordless Kit
C:* #Ifs= 2 Cfg#= 1 Atr=a0 MxPwr=100mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=01 Driver=usbhid
E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
I: If#= 1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=01 Prot=02 Driver=usbhid
E: Ad=82(I) Atr=03(Int.) MxPS= 8 Ivl=14ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 2.06
S: Manufacturer=Linux 2.6.8.1-12mdksmp uhci_hcd
S: Product=UHCI Host Controller
S: SerialNumber=0000:00:1d.0
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
____________________________________
Another thing to do is check the logs for any error messages from the
module. What I find helpfull is to have "tail -f /var/log/messages"
running on one VT, or in a terminal when I plug a devie in, so I can see
any messages. (Actualy, I moduified my syslog configuration so that all
messages are displayed on vt12, so I can just hit Ctrl-Alt-F12 to see
what is going on.)
When I plug the device, I get:
Jun 21 07:23:58 localhost kernel: new high speed device using address 5
------------------ Release Ver = 4330
------------------ EEPORM ver = 4330
Jun 21 7:23:59 localhost net.agent[6958]: add event not handled
Teilhard.
____________________________________________________
Want to buy your Pack or Services from Mandriva?
Go to http://store.mandriva.com
Join the Club : http://www.mandrivaclub.com
____________________________________________________
