Hi Svavar, > On May 9, 2014, at 2:27 AM, Svavar Örn Eysteinsson <[email protected]> wrote: > > Hello List. > > I recently installed and configured OmniOS on a HP Microserver N40L NAS box. > > In time to time my box hangs/freezes for some seconds, when I try to SSH into > the box or execute some SMART-INFO functions. > And then it gives me access. > > In my /var/adm/messages i have these messages : > > May 8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: > /pci@0,0/pci-ide@14,1/ide@0 (ata0): > May 8 20:10:41 blackbox timeout: abort request, target=1 lun=0 > May 8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: > /pci@0,0/pci-ide@14,1/ide@0 (ata0): > May 8 20:10:41 blackbox timeout: abort device, target=1 lun=0 > May 8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: > /pci@0,0/pci-ide@14,1/ide@0 (ata0): > May 8 20:10:41 blackbox timeout: reset target, target=1 lun=0 > May 8 20:10:41 blackbox scsi: [ID 107833 kern.warning] WARNING: > /pci@0,0/pci-ide@14,1/ide@0 (ata0): > May 8 20:10:41 blackbox timeout: reset bus, target=1 lun=0 > May 8 20:10:42 blackbox gda: [ID 107833 kern.warning] WARNING: > /pci@0,0/pci-ide@14,1/ide@0/cmdk@1,0 (Disk0): > May 8 20:10:42 blackbox Error for command 'read sector' Error Level: > Informational > May 8 20:10:42 blackbox gda: [ID 107833 kern.notice] Sense Key: aborted > command > May 8 20:10:42 blackbox gda: [ID 107833 kern.notice] Vendor 'Gen-ATA ' > error code: 0x3 > > > My current configuration is the System(OmniOS) is installed onto a SATA disk > located at port 5 on the Microserver. > (yes i have the BIOS hacked which allows for SATA 3G/AHCI functions on the > port other ports) > Then I have 4x SATA disks configured in RAIDZ > > I double checked my BIOS configuration, and it seems that I have > misconfigured the OS disk into a IDE mode, but not AHCI. > So when I change the mode to AHCI, I get the GRUB loader and the OmniOS logo > after that, but suddenly the machines restarts again > and never boots into the system all the way. > > So my question is, is there any way for my to reconfigure my running-system > to use AHCI instead of IDE,ATA mode ? > > Is it enough to boot up a usb live system and issue a "zpool import -f > rpool", and then finally "zpool export rpool" with a running BIOS-config as > AHCI > and then restart the computer and let it boot normally ?
Yes. > I read somewhere that the import/export functions would update the device > path, but I have no experience on this issue. Yes, this is the fix. > > Any help would be much appreciated. > > Thanks allot people. Enjoy! -- richard > > Best regards, > > Svavar O > Reykjavik - Iceland > > > _______________________________________________ > OmniOS-discuss mailing list > [email protected] > http://lists.omniti.com/mailman/listinfo/omnios-discuss _______________________________________________ OmniOS-discuss mailing list [email protected] http://lists.omniti.com/mailman/listinfo/omnios-discuss
