Hello Guys, It's working. Thanks a lot to all of you :)
On Mon, Aug 3, 2015 at 10:43 AM, David Lang <da...@lang.hm> wrote: > The way to do this is to first forget about the factory reset problem and > configure the AP to do what you want (including any encryption) > > then you can take the resulting file and put it into the build system so > that it becomes the 'factory default' settings. > > Since you are not understanding how to configure the files from the > documentation, configure them from the GUI and then look at the resulting > files. > > David Lang > > > On Mon, 3 Aug 2015, John kerry wrote: > > Hi All, >> >> I created separate files directory and added network and wireless files >> and >> its working everything but still i am not able to use encryption wpa2. >> Below is the my script. >> config wifi-device wifi0 >> option type qcawifi >> option channel auto >> option macaddr 00:03:7f:42:06:61 >> option hwmode 11ng >> # REMOVE THIS LINE TO ENABLE WIFI: >> option disabled 0 >> >> config wifi-iface >> option device wifi0 >> option network lan >> option mode ap >> option ssid CD-1 >> option encryption psk2 >> option key CD-1 >> >> M I doing anything wrong? >> >> Thanks, >> >> On Mon, Aug 3, 2015 at 6:40 AM, David Lang <da...@lang.hm> wrote: >> >> to make the config be there after a factory reset, you need to put the >>> changes into the image that you build. >>> >>> you already did this for /etc/config/network, do the same thing for >>> /etc/config/wireless >>> >>> David Lang >>> >>> >>> On Sun, 2 Aug 2015, John kerry wrote: >>> >>> Hi Leiten, >>> >>>> >>>> I have one issue, after upgrading this firmware it will load wireless >>>> configuration with this changes, actually it should load when i do >>>> factory >>>> reset. >>>> >>>> Thanks, >>>> >>>> On Sun, Aug 2, 2015 at 3:45 PM, John kerry <kerry9...@gmail.com> wrote: >>>> >>>> Hi Leiten, >>>> >>>>> >>>>> Thank you so much, Its working :) >>>>> >>>>> On Sun, Aug 2, 2015 at 3:12 PM, N.Leiten <nicklei...@gmail.com> wrote: >>>>> >>>>> Hi, >>>>> >>>>>> >>>>>> Don't answer to my e-mail only, you need to add openwrt-devel maillist >>>>>> to >>>>>> CC or just answer to CC, in each case I'll receive message but also >>>>>> everyone could see all discussion. >>>>>> >>>>>> In email dated Воскресенье - 02 августа 2015 12:54:32 user John kerry >>>>>> wrote: >>>>>> >>>>>> Hi Leiten, >>>>>>> >>>>>>> I have added new files under and written below : >>>>>>> vi target/linux/ar71xx/base-files/etc/uci-defaults/wireless >>>>>>> >>>>>>> >>>>>> Use index in prefix of filename to set order of execution, so it'll be >>>>>> like '99-wireless'. >>>>>> >>>>>> >>>>>> #!/bin/sh >>>>>>> # >>>>>>> # Copyright (c) 2013 The Linux Foundation. All rights reserved. >>>>>>> # Copyright (C) 2011 OpenWrt.org >>>>>>> # >>>>>>> >>>>>>> [ -e /etc/config/wireless ] && exit 0 >>>>>>> >>>>>>> >>>>>> Here is the problem. When uci-defaults invoke scripts there's already >>>>>> preconfiguration done and /etc/config/wireless already exists, so your >>>>>> script just exit at this point. Remove this line. >>>>>> >>>>>> >>>>>> touch /etc/config/wireless >>>>>>> >>>>>>> uci set wireless.@wifi-device[0].disabled=0; >>>>>>> uci set system.@system[0].hostname=test_ap >>>>>>> uci set wireless.@wifi-iface[0].mode=ap >>>>>>> uci set wireless.@wifi-iface[0].ssid=CD-2.4D >>>>>>> uci set wireless.@wifi-iface[0].encryption=none >>>>>>> uci set wireless.@wifi-iface[0].wds=1 >>>>>>> uci set wireless.radio0.disabled=0 >>>>>>> >>>>>>> uci commit wireless >>>>>>> >>>>>>> exit 0 >>>>>>> >>>>>>> and compile the source code using make V=s but still not changed >>>>>>> default >>>>>>> settings. >>>>>>> >>>>>>> Please help me to make it works. >>>>>>> >>>>>>> Thanks, >>>>>>> >>>>>>> >>>>>>> On Sat, Aug 1, 2015 at 4:38 PM, N.Leiten <nicklei...@gmail.com> >>>>>>> wrote: >>>>>>> >>>>>>> You can also use uci-defaults mechanism for your purpose. Just put >>>>>>> >>>>>>>> script in base-files/etc/uci-defaults and set your preferrable >>>>>>>> parameters with uci and don't forget to 'exit 0' at the end of >>>>>>>> script, >>>>>>>> in elsecase it'll be run every time at boot ruining changes. >>>>>>>> >>>>>>>> 2015-07-31 12:08 GMT+03:00 John kerry <kerry9...@gmail.com>: >>>>>>>> >>>>>>>> Hi, >>>>>>>>> >>>>>>>>> I am working on Ar71xx openWRT Luci project. By default the Wi-Fi >>>>>>>>> is >>>>>>>>> disabled and SSID is OpenWrt. I need to change the default >>>>>>>>> settings. >>>>>>>>> Could anyone help me to change the default settings. >>>>>>>>> >>>>>>>>> >>>>>>>>> Best Regards, >>>>>>>>> John >>>>>>>>> >>>>>>>>> _______________________________________________ >>>>>>>>> openwrt-devel mailing list >>>>>>>>> openwrt-devel@lists.openwrt.org >>>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>>>>>>>> >>>>>>>>> _______________________________________________ >>>>>>>>> >>>>>>>> openwrt-devel mailing list >>>>>>>> openwrt-devel@lists.openwrt.org >>>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>>>>>>> >>>>>>>> _______________________________________________ >>>>>>>> >>>>>>> openwrt-devel mailing list >>>>>> openwrt-devel@lists.openwrt.org >>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>>>>> >>>>>> >>>>>> >>>>> >>>>>
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel