can you connect via a wired port?
given that you've been changing /etc/config/network and /etc/config/wireless,
could you show us what you ended up with there?
David Lang
On Tue, 4 Aug 2015, John kerry wrote:
Hi,
I am using ar71xx OpenWrt. I have connected internet connection to WAN port
and my PC to LAN. I have enabled the WiFi0. The LAN port static IP i am
able to open GUI and even my mobile i connected to Wifi AP and able to open
GUI in mobile. But I am not able to access internet on mobile which is
connected to wifi0 AP.
I have added below script under /etc/firewall.user file.
iptables ...flush
iptables --table nat --flush
iptables --delete-chain
iptables --table nat --delete-chain
iptables -A FORWARD -j ACCEPT -i br-lan -o eth0.2 -m state --state NEW
iptables -A FORWARD -m state --state ESTABLISHED,RELATED -j ACCEPT
iptables -A POSTROUTING -t nat -o eth0.2 -j MASQUERADE
echo 1 > /proc/sys/net/ipv4/ip_forward
#where br-lan = LAN
eth0.2 = WAN
Could anyone help me to write the proper NAT rules so that able to access
the internet.
Thanks,
On Mon, Aug 3, 2015 at 11:29 AM, John kerry <kerry9...@gmail.com> wrote:
Hello Guys,
It's working. Thanks a lot to all of you :)
On Mon, Aug 3, 2015 at 10:43 AM, David Lang <da...@lang.hm> wrote:
The way to do this is to first forget about the factory reset problem and
configure the AP to do what you want (including any encryption)
then you can take the resulting file and put it into the build system so
that it becomes the 'factory default' settings.
Since you are not understanding how to configure the files from the
documentation, configure them from the GUI and then look at the resulting
files.
David Lang
On Mon, 3 Aug 2015, John kerry wrote:
Hi All,
I created separate files directory and added network and wireless files
and
its working everything but still i am not able to use encryption wpa2.
Below is the my script.
config wifi-device wifi0
option type qcawifi
option channel auto
option macaddr 00:03:7f:42:06:61
option hwmode 11ng
# REMOVE THIS LINE TO ENABLE WIFI:
option disabled 0
config wifi-iface
option device wifi0
option network lan
option mode ap
option ssid CD-1
option encryption psk2
option key CD-1
M I doing anything wrong?
Thanks,
On Mon, Aug 3, 2015 at 6:40 AM, David Lang <da...@lang.hm> wrote:
to make the config be there after a factory reset, you need to put the
changes into the image that you build.
you already did this for /etc/config/network, do the same thing for
/etc/config/wireless
David Lang
On Sun, 2 Aug 2015, John kerry wrote:
Hi Leiten,
I have one issue, after upgrading this firmware it will load wireless
configuration with this changes, actually it should load when i do
factory
reset.
Thanks,
On Sun, Aug 2, 2015 at 3:45 PM, John kerry <kerry9...@gmail.com>
wrote:
Hi Leiten,
Thank you so much, Its working :)
On Sun, Aug 2, 2015 at 3:12 PM, N.Leiten <nicklei...@gmail.com>
wrote:
Hi,
Don't answer to my e-mail only, you need to add openwrt-devel
maillist
to
CC or just answer to CC, in each case I'll receive message but also
everyone could see all discussion.
In email dated Воскресенье - 02 августа 2015 12:54:32 user John kerry
wrote:
Hi Leiten,
I have added new files under and written below :
vi target/linux/ar71xx/base-files/etc/uci-defaults/wireless
Use index in prefix of filename to set order of execution, so it'll
be
like '99-wireless'.
#!/bin/sh
#
# Copyright (c) 2013 The Linux Foundation. All rights reserved.
# Copyright (C) 2011 OpenWrt.org
#
[ -e /etc/config/wireless ] && exit 0
Here is the problem. When uci-defaults invoke scripts there's already
preconfiguration done and /etc/config/wireless already exists, so
your
script just exit at this point. Remove this line.
touch /etc/config/wireless
uci set wireless.@wifi-device[0].disabled=0;
uci set system.@system[0].hostname=test_ap
uci set wireless.@wifi-iface[0].mode=ap
uci set wireless.@wifi-iface[0].ssid=CD-2.4D
uci set wireless.@wifi-iface[0].encryption=none
uci set wireless.@wifi-iface[0].wds=1
uci set wireless.radio0.disabled=0
uci commit wireless
exit 0
and compile the source code using make V=s but still not changed
default
settings.
Please help me to make it works.
Thanks,
On Sat, Aug 1, 2015 at 4:38 PM, N.Leiten <nicklei...@gmail.com>
wrote:
You can also use uci-defaults mechanism for your purpose. Just put
script in base-files/etc/uci-defaults and set your preferrable
parameters with uci and don't forget to 'exit 0' at the end of
script,
in elsecase it'll be run every time at boot ruining changes.
2015-07-31 12:08 GMT+03:00 John kerry <kerry9...@gmail.com>:
Hi,
I am working on Ar71xx openWRT Luci project. By default the Wi-Fi
is
disabled and SSID is OpenWrt. I need to change the default
settings.
Could anyone help me to change the default settings.
Best Regards,
John
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
