On Fri, Jan 29, 2010 at 4:18 PM, Ronald Artos <[email protected]> wrote:
> May usb_modeswitch ka na naka-install?? > None that I know, pero is it still required despite the fact that NM can easily dial it? > > Anong unit yan huawei?? ung unit na ginagamit din ng Sun Broadband > Wireless??? > > Yes, its a huawei e1552. > > > -------- > > > 2010/1/29 david t. asuncion, jr. <[email protected]> > >> Alam ko po na sobrang dali po itong isetup sa Network-Manager. >> >> Pero ang problema po ay AYAW ko pong gumamit ng Network-Manager, ang balak >> ko pong gamitin ay WICD. >> >> Un nga lang, walang utility si WICD para maconnect is Globe Tattoo. >> >> So ang tingin kong puedeng gamitin ay WVDIAL. >> >> Meron po bang makakatulong sa inyo na maibigay sa akin ng step by step >> paano mapagana ang Globe Tattoo via WVDIAL? >> >> Eto po output ng lsusb >> >> Quote: >> Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 002 Device 004: ID 04f2:b044 Chicony Electronics Co., Ltd >> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 005 Device 002: ID 1d57:ac01 >> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Bus 001 Device 003: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB >> Modem >> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >> Eto po output ng sudo wvdialconf >> >> Quote: >> Modem Port Scan<*1>: S0 S1 S2 S3 >> WvModem<*1>: Cannot get information for serial port. >> ttyUSB0<*1>: ATQ0 V1 E1 -- OK >> ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK >> ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK >> ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK >> ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK >> ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK >> ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: huawei >> ttyUSB0<*1>: Speed 9600: AT -- OK >> ttyUSB0<*1>: Max speed is 9600; that should be safe. >> ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK >> WvModem<*1>: Cannot get information for serial port. >> ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud >> ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud >> ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. >> WvModem<*1>: Cannot get information for serial port. >> ttyUSB2<*1>: ATQ0 V1 E1 -- OK >> ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK >> ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK >> ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK >> ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK >> ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK >> ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: huawei >> ttyUSB2<*1>: Speed 9600: AT -- OK >> ttyUSB2<*1>: Max speed is 9600; that should be safe. >> ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK >> >> Found a modem on /dev/ttyUSB0. >> Modem configuration written to /etc/wvdial.conf. >> ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" >> ttyUSB2<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" >> Eto naman po laman ng /etc/wvdial.conf >> >> Quote: >> [Dialer Defaults] >> Init1 = ATZ >> Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> Init3 = AT+CGDCONT=1,”IP”,”http.globe.com.ph” >> Stupid Mode = yes >> Modem Type = Analog Modem >> ISDN = 0 >> New PPPD = yes >> Phone = *99# >> Modem = /dev/ttyUSB0 >> Username = globe >> Password = globe >> Baud = 9600 >> At ang pinakamasakit, eto po ang output ng wvdial >> >> Quote: >> --> WvDial: Internet dialer version 1.60 >> --> Cannot get information for serial port. >> --> Initializing modem. >> --> Sending: ATZ >> ATZ >> OK >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> OK >> --> Sending: AT+CGDCONT=1,”IP”,”http.globe.com.ph” >> AT+CGDCONT=1,b [1d]IPb [1d],b [1d]http.globe.com.phb [1d] >> ERROR >> --> Bad init string. >> --> Cannot get information for serial port. >> --> Initializing modem. >> --> Sending: ATZ >> ATZ >> OK >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> OK >> --> Sending: AT+CGDCONT=1,”IP”,”http.globe.com.ph” >> AT+CGDCONT=1,b [1d]IPb [1d],b [1d]http.globe.com.phb [1d] >> ERROR >> --> Bad init string. >> --> Cannot get information for serial port. >> --> Initializing modem. >> --> Sending: ATZ >> ATZ >> OK >> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 >> OK >> --> Sending: AT+CGDCONT=1,”IP”,”http.globe.com.ph” >> AT+CGDCONT=1,b [1d]IPb [1d],b [1d]http.globe.com.phb [1d] >> ERROR >> --> Bad init string. >> >> Salamat po! >> _________________________________________________ >> Philippine Linux Users' Group (PLUG) Mailing List >> http://lists.linux.org.ph/mailman/listinfo/plug >> Searchable Archives: http://archives.free.net.ph >> > > > _________________________________________________ > Philippine Linux Users' Group (PLUG) Mailing List > http://lists.linux.org.ph/mailman/listinfo/plug > Searchable Archives: http://archives.free.net.ph > -- David Tacasa Asuncion, Jr. website keeper, forever linux newbie, BUM extraordinaire Linux User # 406430 http://counter.li.org/ GPG: 0A024BC0
_________________________________________________ Philippine Linux Users' Group (PLUG) Mailing List http://lists.linux.org.ph/mailman/listinfo/plug Searchable Archives: http://archives.free.net.ph
