Mine works out of the box in Ubuntu 9.10 using NM, but below is my wvdial config when I tired using wvdial.
[Dialer Defaults] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Init3 = AT+CGDCONT=1,"IP","http.globe.com.ph" ISDN = 0 Phone = *99# New PPPD = yes Modem = /dev/ttyUSB0 ##try to tail -f your log when you place your globe tatto and see what /dev it was place. Username = yourusername ##leave blank. Password = yourpassword ##leave blank. Baud = 460800 Idle Seconds = 3000 Auto DNS = 1 Stupid Mode = 1 Compuserve = 0 Baud = 460800 Dial Command = ATD Ask Password = 0 FlowControl = NO Hope this help. Regards, AC 2010/1/29 david t. asuncion, jr. <[email protected]> > Alam ko po na sobrang dali po itong isetup sa Network-Manager. > > Pero ang problema po ay AYAW ko pong gumamit ng Network-Manager, ang balak > ko pong gamitin ay WICD. > > Un nga lang, walang utility si WICD para maconnect is Globe Tattoo. > > So ang tingin kong puedeng gamitin ay WVDIAL. > > Meron po bang makakatulong sa inyo na maibigay sa akin ng step by step > paano mapagana ang Globe Tattoo via WVDIAL? > > Eto po output ng lsusb > > Quote: > Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 002 Device 004: ID 04f2:b044 Chicony Electronics Co., Ltd > Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 005 Device 002: ID 1d57:ac01 > Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Bus 001 Device 003: ID 12d1:1001 Huawei Technologies Co., Ltd. E620 USB > Modem > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub > Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub > Eto po output ng sudo wvdialconf > > Quote: > Modem Port Scan<*1>: S0 S1 S2 S3 > WvModem<*1>: Cannot get information for serial port. > ttyUSB0<*1>: ATQ0 V1 E1 -- OK > ttyUSB0<*1>: ATQ0 V1 E1 Z -- OK > ttyUSB0<*1>: ATQ0 V1 E1 S0=0 -- OK > ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttyUSB0<*1>: Modem Identifier: ATI -- Manufacturer: huawei > ttyUSB0<*1>: Speed 9600: AT -- OK > ttyUSB0<*1>: Max speed is 9600; that should be safe. > ttyUSB0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > WvModem<*1>: Cannot get information for serial port. > ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud > ttyUSB1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 9600 baud > ttyUSB1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up. > WvModem<*1>: Cannot get information for serial port. > ttyUSB2<*1>: ATQ0 V1 E1 -- OK > ttyUSB2<*1>: ATQ0 V1 E1 Z -- OK > ttyUSB2<*1>: ATQ0 V1 E1 S0=0 -- OK > ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK > ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK > ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > ttyUSB2<*1>: Modem Identifier: ATI -- Manufacturer: huawei > ttyUSB2<*1>: Speed 9600: AT -- OK > ttyUSB2<*1>: Max speed is 9600; that should be safe. > ttyUSB2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK > > Found a modem on /dev/ttyUSB0. > Modem configuration written to /etc/wvdial.conf. > ttyUSB0<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > ttyUSB2<Info>: Speed 9600; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" > Eto naman po laman ng /etc/wvdial.conf > > Quote: > [Dialer Defaults] > Init1 = ATZ > Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > Init3 = AT+CGDCONT=1,”IP”,”http.globe.com.ph” > Stupid Mode = yes > Modem Type = Analog Modem > ISDN = 0 > New PPPD = yes > Phone = *99# > Modem = /dev/ttyUSB0 > Username = globe > Password = globe > Baud = 9600 > At ang pinakamasakit, eto po ang output ng wvdial > > Quote: > --> WvDial: Internet dialer version 1.60 > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Sending: AT+CGDCONT=1,”IP”,”http.globe.com.ph” > AT+CGDCONT=1,b [1d]IPb [1d],b [1d]http.globe.com.phb [1d] > ERROR > --> Bad init string. > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Sending: AT+CGDCONT=1,”IP”,”http.globe.com.ph” > AT+CGDCONT=1,b [1d]IPb [1d],b [1d]http.globe.com.phb [1d] > ERROR > --> Bad init string. > --> Cannot get information for serial port. > --> Initializing modem. > --> Sending: ATZ > ATZ > OK > --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 > OK > --> Sending: AT+CGDCONT=1,”IP”,”http.globe.com.ph” > AT+CGDCONT=1,b [1d]IPb [1d],b [1d]http.globe.com.phb [1d] > ERROR > --> Bad init string. > > Salamat po! > _________________________________________________ > Philippine Linux Users' Group (PLUG) Mailing List > http://lists.linux.org.ph/mailman/listinfo/plug > Searchable Archives: http://archives.free.net.ph > -- AC Perdon Registered GNU/Linux User #340122
_________________________________________________ Philippine Linux Users' Group (PLUG) Mailing List http://lists.linux.org.ph/mailman/listinfo/plug Searchable Archives: http://archives.free.net.ph
