On Tue, 2025-01-21 at 15:04 +0800, Jamin Lin wrote:
> The design of INTC controllers has significantly changed in AST2700 A1.
>
> There are a total of 480 interrupt sources in AST2700 A1. For interrupt
> numbers
> from 0 to 127, they can route directly to PSP, SSP, and TSP. Due to the
> limitation of interrupt numbers of processors, the interrupts are merged every
> 32 sources for interrupt numbers greater than 127.
>
> There are two levels of interrupt controllers, INTC0 and INTC1. The interrupt
> sources of INTC0 are the interrupt numbers from INTC_0 to INTC_127 and
> interrupts from INTC1. The interrupt sources of INTC1 are the interrupt
> numbers
> greater than INTC_127. INTC1 controls the interrupts INTC_128 to INTC_319
> only.
>
> Currently, only GIC 192 to 201 are supported, and their source interrupts are
> from INTC1 and connected to INTC0 at input pin 0 and output pins 0 to 9 for
> GIC 192-201.
>
> To support both AST2700 A1 and A0, INTC0 input pins 1 to 9 and output pins
> 10 to 18 remain to support GIC 128-136, which source interrupts from INTC0.
> These will be removed if we decide not to support AST2700 A0 in the future.
>
> +---------------------------------------------------------------------------------------+
> > AST2700 A1 Design
> > |
> >
> > |
> > +--------------------------+
> > |
> > | INTC1 | +---------------+
> > |
> > | | | orgates[0] |
> > |
> > orgates[0]+----> |inpin[0]+------->outpin[0]+------> | 0 |
> > |
> > orgates[1]|----> |inpin[1]|------->outpin[1]|------> | 1 0-31 bits
> > +--+ |
> > orgates[2]|----> |inpin[2]|------->outpin[2]|------> | 2 |
> > | |
> > orgates[3]|----> |inpin[3]|------->outpin[3]|------> | 3 |
> > | |
> > orgates[4]|----> |inpin[4]|------->outpin[4]|------> | 4 |
> > | |
> > orgates[5]+----> |inpin[5]+------->outpin[5]+------> | 5 |
> > | |
> > | | |---------------|
> > | |
> > +--------------------------+
> > | |
> >
> > +-----------------------------------------------------------------------|
> > |
> > |
> > |
> > |
> > |
> > | +------------------------------+
> > +-----------------+ |
> > | | INTC0 | | GIC
> > | |
> > | |inpin[0:0]--------->outpin[0] +---------> |192
> > | |
> > | |inpin[0:1]|-------->outpin[1] |---------> |193
> > | |
> > | |inpin[0:2]|-------->outpin[2] |---------> |194
> > | |
> > | |inpin[0:3]|-------->outpin[3] |---------> |195
> > | |
> > >--------------> |inpin[0:4]|-------->outpin[4] |---------> |196
> > | |
> > |inpin[0:5]|-------->outpin[5] |---------> |197
> > | |
> > |inpin[0:6]|-------->outpin[6] |---------> |198
> > | |
> > |inpin[0:7]|-------->outpin[7] |---------> |199
> > | |
> > |inpin[0:8]|-------->outpin[8] |---------> |200
> > | |
> > |inpin[0:9]|-------->outpin[9] |---------> |201
> > | |
> +---------------------------------------------------------------------------------------+
> +---------------------------------------------------------------------------------------+
> > orgates[1]|-----> |inpin[1]|---------->outpin[10]|---------> |128
> > | |
> > orgates[2]|-----> |inpin[2]|---------->outpin[11]|---------> |129
> > | |
> > orgates[3]|-----> |inpin[3]|---------->outpin[12]|---------> |130
> > | |
> > orgates[4]|-----> |inpin[4]|---------->outpin[13]|---------> |131
> > | |
> > orgates[5]|-----> |inpin[5]|---------->outpin[14]|---------> |132
> > | |
> > orgates[6]|-----> |inpin[6]|---------->outpin[15]|---------> |133
> > | |
> > orgates[7]|-----> |inpin[7]|---------->outpin[16]|---------> |134
> > | |
> > orgates[8]|-----> |inpin[8]|---------->outpin[17]|---------> |135
> > | |
> > orgates[9]+-----> |inpin[9]|---------->outpin[18]+---------> |136
> > | |
> > +------------------------------+
> > +-----------------+ |
> >
> > |
> > AST2700 A0 Design
> > |
> >
> > |
> +---------------------------------------------------------------------------------------+
>
Okay, so I think this is the diagram and discussion I asked for as
documentation earlier. I still prefer it doesn't just live in a commit
message, that you pull it out to a separate document that we can easily
point to and evolve.
I'm a little hazy on some of your notation in diagram though. Can you
explain your use of pipes ("|"), plusses ("+"), the "orgates" to the
left of INTC1 (what are they ORing?), and the choice of 5 lines into
the "orgates[0]" box? Also why does the "orgates[0]" arrow point where
it does on INTC0?
Andrew
