It's 40 pitch "table top" chain.  The pads are acetal plastic.  That kind of
chain is on Ebay
all the time.  The drive sprocket is 21 tooth if I remember correctly.  The
motors are similar
to the M-01 motors, but without a base and they are 450W each and running at
about 450
RPMs at 24V.  I'm using the stock 42 pitch 9 tooth sprocket on the motor
mated to a 40 pitch  9
tooth sprocket on the drive shaft all driven by 41 pitch chain.  The motors
can be adjusted
front to rear to keep the drive chains tightened.  The outside of the motor
mount slides into
a triangle piece of wood at the front of the hull.  The triange is glued and
screwed to the front
angle of the hull and to the track sponsons.  That keeps the front of the
mount in place.  The
rear of the mount uses two pieces of wood screwed together in an "L" to
allow for space for
the mount to slide to the rear and it also keeps the rear of the mount from
moving.  That is
screwed and glued to the upper hull sides.  The motors can be removed by
removing 4 screws.
Just to ensue there was no movement of the mounts, I put the top brace on
across the two
mounts.  Basically the systems (suspension, motor mounts, suspension arms,
etc.) are all
varients of the designs I used in the Sturmtiger.  All of the mount pieces
are made from either
solid wood or 1" plywood I had in the garage.  The lower hull pieces are all
1/2" ply except the
lower front slope, that is aluminum plate and can be removed to get to the
drive shafts for maintenance.
I've put power to both tracks and everything seems to be aligned well.  Now
time will tell if the tracks
will stay on, but I have a few tricks I can try if they have some issues
with that.

Derek
T065

On Sun, Aug 9, 2009 at 8:15 AM, Modena <[email protected]> wrote:

>
> nice work Derek, looking good. at 1/6 it should be about 75cm long,
> that looks like about a 22 tooth sprocket on the front, what pitch is
> the chain? The gearing looks pretty fast.....
>
> :)
>
> Ben
>
> On Aug 9, 5:29 pm, "Chrysanthos Kanellopoulos" <[email protected]>
> wrote:
> > Very clean and straighforward construction. Textbook case. Are these
> motors 24 V?  It is going to fly with those!  I like the way they are
> accommodated in the front of the hull.  And I had thought it would be easy
> to build a quick M113. It looks easy now, after Derek built one.
> > Chrys
> >
> >
> >
> >   ----- Original Message -----
> >   From: Derek Engelhaupt
> >   To: [email protected]
> >   Sent: Sunday, August 09, 2009 8:50 AM
> >   Subject: [TANKS] Re: New supply vehicle on the horizon
> >
> >   Just a quick update on progress.  As of today, the suspension is in,
> tracks are mounted,
> >   and motors mounted.  Tomorrow....the electronics go in and hopefully a
> first test drive.
> >   One of the local MP's is doing the final motor mount and track tension
> inspections.  :)
> >
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000001.
> ..
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000002.
> ..
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000003.
> ..
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000004.
> ..
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000005.
> ..
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000006.
> ..
> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000007.
> ..
> >
> http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/backpic.jpg
> >
> >   Derek
> >   T065
> >
>

--~--~---------~--~----~------------~-------~--~----~
You are currently subscribed to the "R/C Tank Combat" group.
To post a message, send email to [email protected]
To unsubscribe, send email to [email protected]
Visit the group at http://groups.google.com/group/rctankcombat
-~----------~----~----~----~------~----~------~--~---

Reply via email to