Chrys,

I would say this would be a general breakdown of what is in it:

Tracks:  Table Top Chain off Ebay $30 shipped
Sprockets:  $25 shipped
Misc. bearings, chain, nuts and bolts:  $60
Speed Controller:  Vantec RDFR 38E $150 off Ebay shipped
Motors:  MY1018Z $140 shipped
Hull:  all wood scrounged from my scrap wood piles - free
Batteries:  taken from other vehicles I have (21st Century Humvees) - free
Radio:  C6C $40 shipped
Radio Controller:  Pelican wireless game controller $15 shipped

Total with Electronics:  $460
Total without:  $255

I'm probably forgetting some stuff.  Two months is a pretty quick build
considering
there have been many days in that time that I haven't had the time to work
on it.

Derek (back to building)
T065


On Sun, Aug 9, 2009 at 2:42 PM, Chrysanthos Kanellopoulos <[email protected]
> wrote:

>  Derek, Will you send us the overall budget save the electronics, and teh
> weight of teh vehicle without batteries?  If I had seen your M113, I would
> have built an exact copy of this one, using the same materials. Great model
> for beginners or for those who want a quick project!
> Chrys
>
>
> ----- Original Message -----
> *From:* Derek Engelhaupt <[email protected]>
> *To:* [email protected]
> *Sent:* Sunday, August 09, 2009 7:07 PM
> *Subject:* [TANKS] Re: New supply vehicle on the horizon
>
> It's 40 pitch "table top" chain.  The pads are acetal plastic.  That kind
> of chain is on Ebay
> all the time.  The drive sprocket is 21 tooth if I remember correctly.  The
> motors are similar
> to the M-01 motors, but without a base and they are 450W each and running
> at about 450
> RPMs at 24V.  I'm using the stock 42 pitch 9 tooth sprocket on the motor
> mated to a 40 pitch  9
> tooth sprocket on the drive shaft all driven by 41 pitch chain.  The motors
> can be adjusted
> front to rear to keep the drive chains tightened.  The outside of the motor
> mount slides into
> a triangle piece of wood at the front of the hull.  The triange is glued
> and screwed to the front
> angle of the hull and to the track sponsons.  That keeps the front of the
> mount in place.  The
> rear of the mount uses two pieces of wood screwed together in an "L" to
> allow for space for
> the mount to slide to the rear and it also keeps the rear of the mount from
> moving.  That is
> screwed and glued to the upper hull sides.  The motors can be removed by
> removing 4 screws.
> Just to ensue there was no movement of the mounts, I put the top brace on
> across the two
> mounts.  Basically the systems (suspension, motor mounts, suspension arms,
> etc.) are all
> varients of the designs I used in the Sturmtiger.  All of the mount pieces
> are made from either
> solid wood or 1" plywood I had in the garage.  The lower hull pieces are
> all 1/2" ply except the
> lower front slope, that is aluminum plate and can be removed to get to the
> drive shafts for maintenance.
> I've put power to both tracks and everything seems to be aligned well.  Now
> time will tell if the tracks
> will stay on, but I have a few tricks I can try if they have some issues
> with that.
>
> Derek
> T065
>
> On Sun, Aug 9, 2009 at 8:15 AM, Modena <[email protected]> wrote:
>
>>
>> nice work Derek, looking good. at 1/6 it should be about 75cm long,
>> that looks like about a 22 tooth sprocket on the front, what pitch is
>> the chain? The gearing looks pretty fast.....
>>
>> :)
>>
>> Ben
>>
>> On Aug 9, 5:29 pm, "Chrysanthos Kanellopoulos" <[email protected]>
>> wrote:
>> > Very clean and straighforward construction. Textbook case. Are these
>> motors 24 V?  It is going to fly with those!  I like the way they are
>> accommodated in the front of the hull.  And I had thought it would be easy
>> to build a quick M113. It looks easy now, after Derek built one.
>> > Chrys
>> >
>> >
>> >
>> >   ----- Original Message -----
>> >   From: Derek Engelhaupt
>> >   To: [email protected]
>> >   Sent: Sunday, August 09, 2009 8:50 AM
>> >   Subject: [TANKS] Re: New supply vehicle on the horizon
>> >
>> >   Just a quick update on progress.  As of today, the suspension is in,
>> tracks are mounted,
>> >   and motors mounted.  Tomorrow....the electronics go in and hopefully a
>> first test drive.
>> >   One of the local MP's is doing the final motor mount and track tension
>> inspections.  :)
>> >
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000001.
>> ..
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000002.
>> ..
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000003.
>> ..
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000004.
>> ..
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000005.
>> ..
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000006.
>> ..
>> >  http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/IM000007.
>> ..
>>  >
>> http://i154.photobucket.com/albums/s265/nitzerebbhead/M113A3/backpic.jpg
>> >
>> >   Derek
>> >   T065
>>
>>
> >
>

--~--~---------~--~----~------------~-------~--~----~
You are currently subscribed to the "R/C Tank Combat" group.
To post a message, send email to [email protected]
To unsubscribe, send email to [email protected]
Visit the group at http://groups.google.com/group/rctankcombat
-~----------~----~----~----~------~----~------~--~---

Reply via email to