Coy.. I was just joking.. However, if you could get an air connector
mounted on the antenna base somewhere and put pressure on it, then you could
soap the antenna and look for bubbles. Once you get the antenna sealed,
then perhaps you could charge it, or at least let it weep through the air
fitting if it was positioned properly to act as a drain.
Tight transmission lines are often pressurized with nitrogen. Microwave and
cellular lines and antennae are often pressurized using dry air. A
dehydrator, a compressor with a dryer, won't run out and need replacement
like a nitrogen bottle would, and is more suited to leaky antenna systems.
As long as you keep positive pressure on the line... no worrys... concerning
water ingress anyway.
Seriously, I don't know much about the Diamond X500 (dimensions, etc.), but
if you can put an air fitting on it, then you can probably fix it.. Perhaps
you can go to the auto parts or the tire store to get an air fitting. They
pressurize tires, don't they? (Let me know if you spin balance it.. hi hi!)
Steve
----- Original Message -----
From: "Coy Hilton" <[EMAIL PROTECTED]>
To: <Repeater-Builder@yahoogroups.com>
Sent: Friday, October 15, 2004 8:19 PM
Subject: [Repeater-Builder] Re: Diamond X500
>
>
> Steve, Great thinking !! sounds like something a thinker, or
> engineer would come up with. I would even take this one under
> advisement.
> 73
> AC0Y
>
>
> --- In Repeater-Builder@yahoogroups.com, "Steve Grantham"
> <[EMAIL PROTECTED]> wrote:
> > As long as we're engineering solutions... (hi hi!..) How about
> using an
> > air-dielectric cable and pressurizing the Diamond radome with an
> > inter-connecting jumper (hose) using a dehydrator... Positive air
> pressure,
> > air egress, can prevent water ingress..
> >
> > 73 & HI!
> > Steve
> >
> > ----- Original Message -----
> > From: "Brent" <[EMAIL PROTECTED]>
> > To: <Repeater-Builder@yahoogroups.com>
> > Sent: Friday, October 15, 2004 8:02 PM
> > Subject: Re: [Repeater-Builder] Diamond X500
> >
> >
> > >
> > > Good one Neil, or use it for a Rain gauge. j/k
> > > I have tried to keep moisture out of those antenna and have had
> no luck,
> > do
> > > to them no having a good vent hole at the bottom to release any
> moisture.
> > So
> > > i drilled a little hole near the bottom of the antenna and than
> installed
> > a
> > > small hose like a fishing tank pump hose about 4-5" long and
> routed it
> > > towards the bottom for a drain. it seems to have helped..
> > > Brent
> > >
> > > ----- Original Message -----
> > > From: "Neil McKie" <[EMAIL PROTECTED]>
> > > To: <Repeater-Builder@yahoogroups.com>
> > > Sent: Friday, October 15, 2004 7:54 PM
> > > Subject: Re: [Repeater-Builder] Diamond X500
> > >
> > >
> > > >
> > > >
> > > > Sure !!
> > > >
> > > > Install it inside the building ...
> > > >
> > > > Neil
> > > >
> > > >
> > > > Coy Hilton wrote:
> > > > >
> > > > > Hi Gang,
> > > > > Anyone know anything about keeping water out of a Diamond
> X500
> > > > > antenna for a repeater use, Or any other suggestions, Short
> of
> > > > > heaving it off the side of the building.
> > > > > 73
> > > > > AC0Y
> > > > >
> > > > >
> > > > > Yahoo! Groups Links
> > > > >
> > > > >
> > > > >
> > > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > Yahoo! Groups Links
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > >
> > > > ---
> > > > [This E-mail scanned for viruses at TNWEB LLC]
> > > >
> > > >
> > > >
> > >
> > > ---
> > > [This E-mail scanned for viruses at TNWEB LLC]
> > >
> > >
> > >
> > >
> > >
> > >
> > > Yahoo! Groups Links
> > >
> > >
> > >
> > >
> > >
> > >
> > >
> > >
>
>
>
>
>
>
>
>
> Yahoo! Groups Links
>
>
>
>
>
>
>
>
Yahoo! Groups Links
<*> To visit your group on the web, go to:
http://groups.yahoo.com/group/Repeater-Builder/
<*> To unsubscribe from this group, send an email to:
[EMAIL PROTECTED]
<*> Your use of Yahoo! Groups is subject to:
http://docs.yahoo.com/info/terms/
