"/usr/local/etc/sane.d/dll.d" you have two copies of sane installed, and the one in /usr/local is being used, but it has no config files. I would remove that copy, and re-configure with the proper arguments to overwrite your existing copy. Something like:
./configure --prefix=/usr --sysconfdir=/etc make make install allan On Mon, Nov 22, 2010 at 2:30 AM, Luigi Carbone <lg.carbone at gmail.com> wrote: > In /etc/sane.d/.dll.conf "canon_dr" is listed, > > The result of command SANE_DEBUG_DLL=255 scanimage -L 2>9050.log on terminal > is > > sudo SANE_DEBUG_DLL=255 scanimage -L 2 > 9050.log > [sanei_debug] Setting debug level of dll to 255. > [dll] sane_init: SANE dll backend version 1.0.12 from sane-backends 1.0.21 > [dll] sane_init/read_dlld: processing /usr/local/etc/sane.d/dll.d ... > [dll] sane_init/read_dlld: done. > [dll] sane_init/read_config: Couldn't open config file (dll.conf): No such > file or directory > [dll] sane_get_devices > [dll] sane_get_devices: found 0 devices > [dll] sane_exit: exiting > [dll] sane_exit: finished > > but the 9050.log is attach. > > TKS > > Il 19/11/2010 14:26, m. allan noah ha scritto: >> >> The canon_dr backend is not enabled. check /etc/sane.d/dll.conf, and >> make sure 'canon_dr' is listed there. >> >> If it is listed, then try this: >> >> SANE_DEBUG_DLL=255 scanimage -L 2>9050.log >> >> and send that log. >> >> allan >> >> On Fri, Nov 19, 2010 at 7:56 AM, Luigi Carbone<lg.carbone at gmail.com> >> ?wrote: >>> >>> Mmh, it's same. >>> >>> The log file is attach. >>> >>> Luigi >>> >>> Il 19/11/2010 13:33, m. allan noah ha scritto: >>>> >>>> Ok- as root, run this: >>>> >>>> SANE_DEBUG_CANON_DR=30 scanimage -L 2>9050.log >>>> >>>> then send 9050.log to the list. >>>> >>>> allan >>>> >>>> On Fri, Nov 19, 2010 at 2:03 AM, Luigi Carbone<lg.carbone at gmail.com> >>>> ?wrote: >>>>> >>>>> With a privileges root, this is the result >>>>> >>>>> No scanners were identified. If you were expecting something different, >>>>> check that the scanner is plugged in, turned on and detected by the >>>>> sane-find-scanner tool (if appropriate). Please read the documentation >>>>> which came with this software (README, FAQ, manpages). >>>>> >>>>> :( >>>>> >>>>> Il 18/11/2010 14:20, m. allan noah ha scritto: >>>>>> >>>>>> as root, run the following command, and send output to us: >>>>>> >>>>>> scanimage -L >>>>>> >>>>>> allan >>>>>> >>>>>> On Thu, Nov 18, 2010 at 7:57 AM, Luigi Carbone<lg.carbone at gmail.com> >>>>>> ?wrote: >>>>>>> >>>>>>> Hi all, >>>>>>> I have problem with scanner canon dr-9050C, i have ubuntu 10.04 and >>>>>>> installated driver san version 1.0.21. >>>>>>> >>>>>>> I have configured file canon_dr.conf so >>>>>>> # DR-9050C >>>>>>> usb 0x1083 0x1622 >>>>>>> >>>>>>> the command lsusb returns >>>>>>> >>>>>>> Bus 008 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >>>>>>> Bus 007 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >>>>>>> Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >>>>>>> Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >>>>>>> Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >>>>>>> Bus 003 Device 002: ID 046d:c505 Logitech, Inc. Cordless >>>>>>> Mouse+Keyboard >>>>>>> Receiver >>>>>>> Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub >>>>>>> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >>>>>>> Bus 001 Device 004: ID 152e:2507 LG (HLDS) >>>>>>> Bus 001 Device 003: ID 1083:1622 Canon Electronics, Inc. >>>>>>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub >>>>>>> >>>>>>> the scanner is visible to the system... >>>>>>> >>>>>>> Help me. >>>>>>> -- >>>>> >>> >>> >> >> >> > > > -- > Luigi Carbone > ---------------------- > Owner @ http://www.ingenioweb.it > Web Designer @ www.consulenti-ict.it > CV: http://www.linkedin.com/in/carboneluigi > Skype: corsaro832 > Cell: 340 32 15 783 > -- "The truth is an offense, but not a sin"