On Dec 4, 2013 16:14, ToddAndMargo <toddandma...@zoho.com> wrote:
> On Wed, Dec 4, 2013 at 2:41 PM, ToddAndMargo <toddandma...@zoho.com>
wrote:
>> Hi All,
>>
>> SL 6.5, 64 bit.
>>
>> I had to manually configure a Tread Net TEW-638PAP as a wireless
>> bridge yesterday. In the process, I had to change my default
>> router (a.k.a. gateway) three times. (Networking too, but
>> that worked.) The TEW-638PAP was hooked to my second
>> Ethernet port (eth1).
>>
>> Problem, I had to reboot to get the new default route to
>> stick.
>>
>> Now I know of two places I can put my default router:
>>
>> /etc/sysconfig/network <--- where I put it
>> GATEWAY=192.168.10.100 and
>>
>> /etc/sysconfig/network-scripts/ifcfg-eth1
>> GATEWAY=192.168.10.100
>>
>> I am using /etc/sysconfig/network and the "vi" method.
>>
>> To check my default router setting, I used "netstat -rn"
>> and looked for the tags "UG". (It is at the bottom of
>> the list.)
>>
>> To try to get the new default router setting to take,
>> I used:
>>
>> service network restart; netstat -rn
>> and
>> ifdown eth1; ifup eth1; netstat -rn
>>
>> No joy with either method. Whatever gateway I had when
>> I booted, was the one I was stuck with. Reboot
>> was the only way to make the change. I even tried
>> manually configuring it with "route". No joy there
>> either. :'(
>>
>> What did I do wrong?
>>
>> Many thanks,
>> -T
On 12/04/2013 12:20 PM, Paul Robert Marino wrote:
> ip route delete default via xxx.xxx.xxx.xxx dev eth0
> then
> ip route add default via yyy.yyy.yyy.yyy dev eth0
>
> replace xxx.xxx.xxx.xxx with your current router and yyy.yyy.yyy.yyy
> with the new one
>
> there is also an "ip route replace " syntax as well if you need it
> see "man ip" for more details ;-)
Hi Paul,
Worked beautifully. Thank you!On 12/04/2013 02:42 PM, Paul Robert Marino
wrote:> The delete failed
This is because when it ran ip route delete default via it used the new
address instead of the old one.
So the commands failed.
This is actually a fairly common one.
It always happens with those scripts when you modify the configs;
because they only look at the config file and ignore the current running
state.
Those scripts were written for ifconfig and route commands on the 1.x
kernel and latter patched to use the up command incrementally and as
such there are some core things they don't do quite the way you would
expect.
Again as I've said multiple times they need a fundamental rewrite and
network manager isn't the answer for servers
-- Sent from my HP Pre3
------------------------------------------------------------------------
Any idea why restarting the network service did not catch
my change to /etc/sysconfig/network?
And, should I be setting my router in /etc/sysconfig/network
or /etc/sysconfig/network/scripts/ifcfg-eth1?
-T
Fun command line:
$ ip route | grep -i default | awk '{print $3}'
192.168.240.1
On 12/04/2013 02:42 PM, Paul Robert Marino wrote:> The delete failed
> This is because when it ran ip route delete default via it used the new
> address instead of the old one.
> So the commands failed.
> This is actually a fairly common one.
> It always happens with those scripts when you modify the configs;
> because they only look at the config file and ignore the current running
> state.
> Those scripts were written for ifconfig and route commands on the 1.x
> kernel and latter patched to use the up command incrementally and as
> such there are some core things they don't do quite the way you would
> expect.
> Again as I've said multiple times they need a fundamental rewrite and
> network manager isn't the answer for servers
>
>
>
> -- Sent from my HP Pre3
>
> ------------------------------------------------------------------------
That explains it. Thank you.
--
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Computers are like air conditioners.
They malfunction when you open windows
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~