Re: [Elecraft] [KX3 amp] 100/50
Wow! What a quick feed back. This is Elecraft quality that we love :) Thank you Wayne & Elecraft. 73 Atsu, JE1TRV > Hi Atsu, > > We could provide a jumper or switch in the KXPA100 to limit power to > 50 watts. > > Thanks for the suggestion. > > 73, > Wayne > N6KR > > > On Jan 18, 2012, at 5:06 PM, JE1TRV wrote: > >>> From JA >> I'd like to suggest Elecraft to prepare 50W version amp for KX3 >> since the >> max.power allowed for prtable operation is 50W in JA. >> Small internal swith to select 100/50W might be nice idea for that. >> >> BTW >> Thank you very much Elecraft for accepting direct order from JA. >> >> Atsu, JE1TRV >> __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] [KX3 amp]
>From JA I'd like to suggest Elecraft to prepare 50W version amp for KX3 since the max.power allowed for prtable operation is 50W in JA. Small internal swith to select 100/50W might be nice idea for that. BTW Thank you very much Elecraft for accepting direct order from JA. Atsu, JE1TRV > Can we expect to see the 100w amp before Christmas. I assume it will have > bandpass filters? Be about $500? > I believe that will be the only 100w amp for qrp rigs with filtered output > so it should be popular with other rigs as well. > > 73 > Mike R > > Sent from my spy ring > > Amateur/Ham Radio KE5GBC > HF & Echolink > __ > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] k3 rs232 problem
Juha, OH6OS Did you get solution already? If not please refer following advice that I had given from tech support of Elecraft egarding same problem. ===Q't=== You need to always be careful to remove *all* cables from the K3 is there is a bad lightning storm. We see lots of damage to customer's K1, K2, K3 each summer when this is not done. I learned this the hard way when I lived in Florida where lightning is severe. Possibly U1 on the KIO3 main board is damaged or the negative supply voltage is too low or is missing. We've seen a low negative level on some rigs if the 1kHz oscillator is not working well. With the serial cable removed, please check to see if there is at least -5VDC at U1 pin 8 on the KIO3 main board, or at the gold plated hole which is right next to pin 8 (bottom left side of U1, as you face the front of the rig). -7VDC or more is normal. Also touch U1 to see if it feels hot or warm, or if it looks to be damaged. If you suspect this is the problem, we can send you a new IC for U1, or the entire KIO3 main board will need to be replaced. Also check the little board that has the ACC and RS232 connectors to see if it might have an open SMD RF choke. Use an ohmmeter to see if all of the RFCs show less than 10 ohms as expected. ==Unq't=== GL! Atsu, JE1TRV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] [K3] S/N3050 RS232 port has no response
Dear Elecrafters! Since few days ago, my K3 (S/N3050) has no response from its RS232 port. First no frequency data became obtained by Logger32. Then, I tried to connect by K3 Utility, I tried port refresh, port test,etc. But no reply from the K3. I confirmed K3 Utility program is sending polling signal to K3 RS232 port but seems no reply from K3. I use USB/RS232 converter between P/C and the rig. I changed the connection with other rig such as FT-2000, and it works without problem using same com port, so that I'm sure the RS232 of K3 is something wrong. I'm afraid if K3 got a kind of surge damage because we had a bad wx with lightening just before the reported malfunction occur. I posted same question to tech support but if anyone had same problem please advise how to fix this problem. vy 73 Atsu, JE1TRV from Tokyo Japan __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] QSO PARTY (EQP 2010) RESULTS?
My friend is wondering when QSO PARTY (EQP 2010) results become ready? I could not find on the Elecraft website. Who knows? Atsu, JE1TRV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] test
sri, this is test message Atsu, JE1TRV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 HI-TEMP ALARM
Wayne & Gary, Thanks for the support off the list. After I set PA TEMP to "R ONLY" instead of "T AND R", the problem stopped. I don't know the reason why. But anyway it seems usable with this setting for the time being. Jaakko, Please try this setting on your K3 too. TU & 73 Atsu, JE1TRV - Original Message - From: "Wayne Burdick" To: Cc: Sent: Wednesday, January 13, 2010 1:36 AM Subject: Re: [Elecraft] K3 HI-TEMP ALARM > We're looking into this. > > 73, > Wayne > N6KR > > On Jan 11, 2010, at 7:20 PM, je1...@a1club.net wrote: > >> Hi folks! >> Thank you for suggestions. >> >> In my previous post, I forgot to say that my K3 works without hi-temp >> alarm after warming up (about 30min or so without transmit just >> receiving >> status). >> >> So, it's just the same with Jaako's case. >> My shack temp was around 15C these days. >> >> hmmm... >> >> Atsu, JE1TRV >> >>> Hi >>> >>> I have same problem, when shack temperature is below 17 degrees >>> Celcius >>> >>> When PA Temp is higher than 25 degrees C then power is OK. >>> >>> Jaakko OH1MA / K3 ser. 2952 >>> >>> >>> Hi Elecrafters! >>> >>> I have problem on my K3/100 (S/N3050, factory assembled). >>> When I transmit more than 12W(means hi power amp on) >>> within about 30min after mains power on, HI-TEMP alarm >>> occur and equipment is forced to set 5W. >>> >>> No problem at all when hi-power amp is through ( Po<12W ). >>> >>> Any idea? >>> Thanks in advance >>> 73, Atsu JE1TRV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 HI-TEMP ALARM
Hi folks! Thank you for suggestions. In my previous post, I forgot to say that my K3 works without hi-temp alarm after warming up (about 30min or so without transmit just receiving status). So, it's just the same with Jaako's case. My shack temp was around 15C these days. hmmm... Atsu, JE1TRV > Hi > > I have same problem, when shack temperature is below 17 degrees Celcius > > When PA Temp is higher than 25 degrees C then power is OK. > > Jaakko OH1MA / K3 ser. 2952 > > > Hi Elecrafters! > > I have problem on my K3/100 (S/N3050, factory assembled). > When I transmit more than 12W(means hi power amp on) > within about 30min after mains power on, HI-TEMP alarm > occur and equipment is forced to set 5W. > > No problem at all when hi-power amp is through ( Po<12W ). > > Any idea? > Thanks in advance > 73, Atsu JE1TRV > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 HI-TEMP ALARM
Hi Elecrafters! I have problem on my K3/100 (S/N3050, factory assembled). When I transmit more than 12W(means hi power amp on) within about 30min after mains power on, HI-TEMP alarm occur and equipment is forced to set 5W. No problem at all when hi-power amp is through ( Po<12W ). Any idea? Thanks in advance 73, Atsu JE1TRV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 (yada yada)
Barry and Jim Thank you for interesting info. It's very informative for improvement of my vocabulary. 73 de JE1TRV, Atsu Tokyo Japan KX1 #248 K1 #1082 K2/100 #4255 K3:asking Eric to accept direct order from JA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3
Congrats! Mike First qso was VP6PR, yadayada. . BTW What do you mean "yadayada"? "yadayada" means "No No" by girls or kids in Japanese. 73 de JE1TRV, Atsu Tokyo Japan KX1 #248 K1 #1082 K2/100 #4255 K3:asking Eric to accept direct order from JA ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Uk Dealer -NO THANKS !
As a Japanese Elecraft fan, I do hope Elecraft to reconsider way of selling K3 to JA. As UK friends pointed out, the Japanese reseller price becomes almost in double. In case of KX1,K1 or K2, the Japanese reseller still has some merit for instance they can provide technical support or repairing service when user have trouble during kit building. In case of K3, it is preassembled and pretested so that risk to buy direct from US should be much lower than conventional model. Many of my friends has interest in K3 but they don't want to pay double just for a reseller. Atsu, JE1TRV ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
