RE: [Elecraft] K3 Serial Commands?
Not all published commands work - I will have to look at my K3 as I just selected filter 5 and got filter 1 selected! I'm in Dayton without my K3 and limited e-mail access but I believe my tests indicated the filter number was ignored. All FWx commands simply selected the next filter in sequence. 73, ... Joe, W4TV -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Simon Brown (HB9DRV) Sent: Friday, May 16, 2008 12:17 AM To: n4lq; [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 Serial Commands? FW4; Set the correct speed, I use 38,400 baud. Not all published commands work - I will have to look at my K3 as I just selected filter 5 and got filter 1 selected! Simon Brown, HB9DRV -- From: n4lq [EMAIL PROTECTED] That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
Not quite - something very odd happening, I'll update the firmware over the weekend to get to the latest revision. Simon Brown, HB9DRV -- From: Joe Subich, W4TV [EMAIL PROTECTED] I'm in Dayton without my K3 and limited e-mail access but I believe my tests indicated the filter number was ignored. All FWx commands simply selected the next filter in sequence. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
Steve, Look at the FW commamd in the KIO2 Programmer's Reference. 73, Don W3FPR n4lq wrote: I'm trying to configure Mixw macros so it will send commands to select various filters, FL2 etc The Programmer's Reference isn't much help to me. I was able to interpet the commands for my IC-7800 easily but this has me stumped. Can someone help me get started by telling me the command format for one of the filters? Steve Ellington [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 6:01 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, Look at the FW commamd in the KIO2 Programmer's Reference. 73, Don W3FPR n4lq wrote: I'm trying to configure Mixw macros so it will send commands to select various filters, FL2 etc The Programmer's Reference isn't much help to me. I was able to interpet the commands for my IC-7800 easily but this has me stumped. Can someone help me get started by telling me the command format for one of the filters? Steve Ellington [EMAIL PROTECTED] No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
Steve, I suggest that you read the entire Programmer's Reference paying particular attention to the command syntax. There is more to it than just entering the command itself. During that reading process, you should then understand GET and SET. Try a few commands from a terminal program first to get a feel for the syntax and command usage. After that, review your logging application to see if it automatically adds anything to that which you enter into the macro - if it does, that will have to be taken into consideration. 73, Don W3FPR n4lq wrote: That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 6:01 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, Look at the FW commamd in the KIO2 Programmer's Reference. 73, Don W3FPR n4lq wrote: I'm trying to configure Mixw macros so it will send commands to select various filters, FL2 etc The Programmer's Reference isn't much help to me. I was able to interpet the commands for my IC-7800 easily but this has me stumped. Can someone help me get started by telling me the command format for one of the filters? Steve Ellington [EMAIL PROTECTED] No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
IF someone would just give me one command in the proper syntax I think i could figure this out. I read the manual but it's really vague. Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 7:25 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, I suggest that you read the entire Programmer's Reference paying particular attention to the command syntax. There is more to it than just entering the command itself. During that reading process, you should then understand GET and SET. Try a few commands from a terminal program first to get a feel for the syntax and command usage. After that, review your logging application to see if it automatically adds anything to that which you enter into the macro - if it does, that will have to be taken into consideration. 73, Don W3FPR n4lq wrote: That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 6:01 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, Look at the FW commamd in the KIO2 Programmer's Reference. 73, Don W3FPR n4lq wrote: I'm trying to configure Mixw macros so it will send commands to select various filters, FL2 etc The Programmer's Reference isn't much help to me. I was able to interpet the commands for my IC-7800 easily but this has me stumped. Can someone help me get started by telling me the command format for one of the filters? Steve Ellington [EMAIL PROTECTED] No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1445 - Release Date: 5/15/2008 7:25 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
Steve, You did not use a ; at the end of the command when you posted the macro that you were trying - that may be your sole problem. The other potential problem could be that the K2 is in a state where it will not accept commands. Since I don't know what your application is doing when the macro is invoked, I cannot know for certain whether this is a problem or not. You could try this sequence of commands: RX;K20;FW2; which should select FL2 for you. If you leave the trailing '2' off, the next sequential filter should be selected. 73, Don W3FPR n4lq wrote: IF someone would just give me one command in the proper syntax I think i could figure this out. I read the manual but it's really vague. Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 7:25 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, I suggest that you read the entire Programmer's Reference paying particular attention to the command syntax. There is more to it than just entering the command itself. During that reading process, you should then understand GET and SET. Try a few commands from a terminal program first to get a feel for the syntax and command usage. After that, review your logging application to see if it automatically adds anything to that which you enter into the macro - if it does, that will have to be taken into consideration. 73, Don W3FPR n4lq wrote: That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 6:01 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, Look at the FW commamd in the KIO2 Programmer's Reference. 73, Don W3FPR n4lq wrote: I'm trying to configure Mixw macros so it will send commands to select various filters, FL2 etc The Programmer's Reference isn't much help to me. I was able to interpet the commands for my IC-7800 easily but this has me stumped. Can someone help me get started by telling me the command format for one of the filters? Steve Ellington [EMAIL PROTECTED] No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1445 - Release Date: 5/15/2008 7:25 PM No virus found in this incoming message. Checked by AVG. Version: 8.0.100 / Virus Database: 269.23.16/1434 - Release Date: 5/15/2008 7:24 AM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] K3 Serial Commands?
Don, The question was asked in regard to the K3 - not the K2. Unfortunately, the K3 does not (yet) seem to be able to select a specific filter/bandwidth only the next filter in sequence with the default DSP bandwidth for that filter/mode. Regards, ... Joe Subich (407) 349-4926 (phone) (407) 718-0523 (cell) (407) 349-0379 (fax) -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Don Wilhelm Sent: Thursday, May 15, 2008 9:00 PM To: n4lq Cc: [EMAIL PROTECTED]; Elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 Serial Commands? Steve, You did not use a ; at the end of the command when you posted the macro that you were trying - that may be your sole problem. The other potential problem could be that the K2 is in a state where it will not accept commands. Since I don't know what your application is doing when the macro is invoked, I cannot know for certain whether this is a problem or not. You could try this sequence of commands: RX;K20;FW2; which should select FL2 for you. If you leave the trailing '2' off, the next sequential filter should be selected. 73, Don W3FPR n4lq wrote: IF someone would just give me one command in the proper syntax I think i could figure this out. I read the manual but it's really vague. Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 7:25 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, I suggest that you read the entire Programmer's Reference paying particular attention to the command syntax. There is more to it than just entering the command itself. During that reading process, you should then understand GET and SET. Try a few commands from a terminal program first to get a feel for the syntax and command usage. After that, review your logging application to see if it automatically adds anything to that which you enter into the macro - if it does, that will have to be taken into consideration. 73, Don W3FPR n4lq wrote: That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? Steve Ellington [EMAIL PROTECTED] - Original Message - From: Don Wilhelm [EMAIL PROTECTED] To: n4lq [EMAIL PROTECTED] Cc: Elecraft@mailman.qth.net Sent: Thursday, May 15, 2008 6:01 PM Subject: Re: [Elecraft] K3 Serial Commands? Steve, Look at the FW commamd in the KIO2 Programmer's Reference. 73, Don W3FPR n4lq wrote: I'm trying to configure Mixw macros so it will send commands to select various filters, FL2 etc The Programmer's Reference isn't much help to me. I was able to interpet the commands for my IC-7800 easily but this has me stumped. Can someone help me get started by telling me the command format for one of the filters? Steve Ellington [EMAIL PROTECTED] ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
FW1,FW2,FW3,FW4,FW5 Simon Brown, HB9DRV -- From: Don Wilhelm [EMAIL PROTECTED] Look at the FW commamd in the KIO2 Programmer's Reference. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] K3 Serial Commands?
FW4; Set the correct speed, I use 38,400 baud. Not all published commands work - I will have to look at my K3 as I just selected filter 5 and got filter 1 selected! Simon Brown, HB9DRV -- From: n4lq [EMAIL PROTECTED] That didn't help. I tried entering FW4 and nothing happens as if nothing is being sent. There must be something that preceeds the command. The manual keeps mentioning GET and SETAre you supposed to enter that somewhere? ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com