Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
I find Don's info to be exactly correct as it applies to the USB connection between the radio and computer.As to the Line IN and Line OUT on the back of the radioI've never used it. With Windows 10, if you wish the Sound Card to show the levels in dB, just right click on the level slider in the Recording devices for example. This will give one the option of displaying the level as "decibels" or "percentage". For WSJT-X I find 0 dB about optimum, for HRD/DM780 I use +10 dB and for FLDIGI and MMTTY about +15 dB seems best.For the Speaker level, adjust about mid scale with a full scale value of 50 . In the Playback devices window the level is about - 10 dB. The default value for LINE OUT in my K3S is 010. I've found no need to change this as the other controls in the computer and application software are most adequate. All this applies when using DATA A mode in the K3S. If you aren't using DATA A mode, then be sure any EQ or CMP values are set to zero. 73 Bob, K4TAX S/N 10163 On 6/26/2017 10:43 PM, Don Wilhelm wrote: Jim, What are the settings for the K3S CODEC in the computer? Look at your soundcard settings and set them to something lower. There is normally no need for an additional control in the K3S other than the normal LINE IN gain settings. The settings for the K3/K3S computer LINE OUT (or SPKR) should be about 50%. but lower is K too. The K3/K3S should be set to some mid-range value. If very low or very high, adjust the computer soundcard settings until it adjusts in the K3/K3S midrange. Same goes for LINE OUT - the soundcard LINE IN should be set to about 50% in the computer, set K3/K3S LINE OUT to some value near 8 or 10. For soundcard data modes, you need to adjust the audio drive level for 4 bars solid on the ALC mater with the 5th bar flashing - that is the NO ALC point for the K3/K3S. Adjust the power level with the POWER knob. To do it like the JT instructions tell you will lead to power "hunting" which will include power overshoot. Ignore the JT instructions and the common internet advice which is to set the power to full and adjust the power with the audio level. That is for other transceivers. The Elecraft transceivers control power differently than all other amateur transceivers that I know of. Some commercial gear does work like the K3/K3S with a closed loop power control system. 73, Don W3FPR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
Jim, What are the settings for the K3S CODEC in the computer? Look at your soundcard settings and set them to something lower. There is normally no need for an additional control in the K3S other than the normal LINE IN gain settings. The settings for the K3/K3S computer LINE OUT (or SPKR) should be about 50%. but lower is K too. The K3/K3S should be set to some mid-range value. If very low or very high, adjust the computer soundcard settings until it adjusts in the K3/K3S midrange. Same goes for LINE OUT - the soundcard LINE IN should be set to about 50% in the computer, set K3/K3S LINE OUT to some value near 8 or 10. For soundcard data modes, you need to adjust the audio drive level for 4 bars solid on the ALC mater with the 5th bar flashing - that is the NO ALC point for the K3/K3S. Adjust the power level with the POWER knob. To do it like the JT instructions tell you will lead to power "hunting" which will include power overshoot. Ignore the JT instructions and the common internet advice which is to set the power to full and adjust the power with the audio level. That is for other transceivers. The Elecraft transceivers control power differently than all other amateur transceivers that I know of. Some commercial gear does work like the K3/K3S with a closed loop power control system. 73, Don W3FPR On 6/26/2017 8:59 PM, Jim Rogers wrote: Richard - I second your report, there is no fine adjustment for the USB audio on the K3s either in received audio or transmitted audio. When the band is noisy, I have to reduce LIN OUT to 01 or alternatively reduce the overall system gain with the RF gain (which in the case of the K3 and K3s is IF gain). When operating meteor scatter on 2M with an Elecraft K144XV transverter I had to reduce the audio drive from the JT65 software to 50% to prevent RF power out overshoot and hunting, typical in over-driven closed loop systems. This allowed me to advance LIN IN and the end result was the power detection system of the K3s settled down. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
On 6/26/2017 10:00 PM, Guy Olinger K2AV wrote: Audio from the K3S via USB is never actual audio in the K3S. After the low IF hits the A/D converter, it's number soup everywhere between the A/D and the far end of the USB cable. Wrong! The stereo input of "USB Audio CODEC" is fed by the "Line Out" analog audio. Adjusting MENU:LIN OUT will adjust the audio level into USB Audio CODEC. 73, ... Joe, W4TV On 6/26/2017 10:00 PM, Guy Olinger K2AV wrote: Gotta remember that there's no audio here, just numbers that represent audio. Somewhere in the PC there is a setting that instructs a program to set a reference level for the digital signal. It's not at all like running coax from line out jacks. The digital doesn't pick up hum or flat-top. Just numbers being thrown around. Audio from the K3S via USB is never actual audio in the K3S. After the low IF hits the A/D converter, it's number soup everywhere between the A/D and the far end of the USB cable. On Mon, Jun 26, 2017 at 9:08 PM, dgb wrote: Can't help but wonder, is anyone adjusting the recording and playback in Windows? Mine works fine by adjusting those. I don't do any vhf though. 73 Dwight NS9I On 6/26/2017 7:59 PM, Jim Rogers wrote: Richard - I second your report, there is no fine adjustment for the USB audio on the K3s either in received audio or transmitted audio. When the band is noisy, I have to reduce LIN OUT to 01 or alternatively reduce the overall system gain with the RF gain (which in the case of the K3 and K3s is IF gain). When operating meteor scatter on 2M with an Elecraft K144XV transverter I had to reduce the audio drive from the JT65 software to 50% to prevent RF power out overshoot and hunting, typical in over-driven closed loop systems. This allowed me to advance LIN IN and the end result was the power detection system of the K3s settled down. There are work-arounds. Jim, W4ATK K-Line, K2/10 On 6/26/2017 6:11 PM, Christopher Hoover wrote: USB audio with the default settings has been fine for me from the first day. Check your settings? On Thu, Jun 22, 2017 at 10:31 AM, Dick via Elecraft < elecraft@mailman.qth.net> wrote: Hello Elecraft, When feeding the audio from the K3S USB port to the CPU, the K3S audio level is extremely high and way too hot for good performance on many digital modes. Example, even with my CPU's sound card set at the lowest possible level of "01" my K3S is hitting the JT-65 software with a super strong signal that is much higher than the software wants to see and performance is degraded. The same is true when operating RTTY using MMTTY or 2Tone software. The USB audio output on the K3S needs to be adjustable in the K3S Menu as it was on the K3 Serial port. I wrote to you a few months ago about this without a positive reply. Please address this serious issue. Thank you- Richard Van Zandt- K9OM In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, elecraft-requ...@mailman.qth.net writes: If you are using Line Out with a fixed gain setting to feed audio to WSJT-X, adjusting the AF control will not do anything. What I do is leave my RF gain control at its normal position (around 3 o'clock) and use the slider at the lower left in the WSJT-X window to compensate for gain variations. 73, Rich VE3KI W3FPR wrote: Bret, You may have better luck with running the RF Gain full and adjusting with the AF gain. That way the RX AGC will smooth out variations in the signal level. 73, Don W3FPR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to c...@murgatroid.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to jim.w4...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@bayland.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to k2av@gmail.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
Gotta remember that there's no audio here, just numbers that represent audio. Somewhere in the PC there is a setting that instructs a program to set a reference level for the digital signal. It's not at all like running coax from line out jacks. The digital doesn't pick up hum or flat-top. Just numbers being thrown around. Audio from the K3S via USB is never actual audio in the K3S. After the low IF hits the A/D converter, it's number soup everywhere between the A/D and the far end of the USB cable. On Mon, Jun 26, 2017 at 9:08 PM, dgb wrote: > Can't help but wonder, is anyone adjusting the recording and playback in > Windows? > > Mine works fine by adjusting those. I don't do any vhf though. > > 73 Dwight NS9I > > > > On 6/26/2017 7:59 PM, Jim Rogers wrote: > >> Richard - I second your report, there is no fine adjustment for the USB >> audio on the K3s either in received audio or transmitted audio. When the >> band is noisy, I have to reduce LIN OUT to 01 or alternatively reduce the >> overall system gain with the RF gain (which in the case of the K3 and K3s >> is IF gain). >> >> When operating meteor scatter on 2M with an Elecraft K144XV transverter I >> had to reduce the audio drive from the JT65 software to 50% to prevent RF >> power out overshoot and hunting, typical in over-driven closed loop >> systems. This allowed me to advance LIN IN and the end result was the power >> detection system of the K3s settled down. >> >> There are work-arounds. >> >> Jim, W4ATK >> >> K-Line, K2/10 >> >> >> On 6/26/2017 6:11 PM, Christopher Hoover wrote: >> >>> USB audio with the default settings has been fine for me from the first >>> day. Check your settings? >>> >>> On Thu, Jun 22, 2017 at 10:31 AM, Dick via Elecraft < >>> elecraft@mailman.qth.net> wrote: >>> >>> Hello Elecraft, When feeding the audio from the K3S USB port to the CPU, the K3S audio level is extremely high and way too hot for good performance on many digital modes. Example, even with my CPU's sound card set at the lowest possible level of "01" my K3S is hitting the JT-65 software with a super strong signal that is much higher than the software wants to see and performance is degraded. The same is true when operating RTTY using MMTTY or 2Tone software. The USB audio output on the K3S needs to be adjustable in the K3S Menu as it was on the K3 Serial port. I wrote to you a few months ago about this without a positive reply. Please address this serious issue. Thank you- Richard Van Zandt- K9OM In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, elecraft-requ...@mailman.qth.net writes: If you are using Line Out with a fixed gain setting to feed audio to WSJT-X, adjusting the AF control will not do anything. What I do is leave my RF gain control at its normal position (around 3 o'clock) and use the slider at the lower left in the WSJT-X window to compensate for gain variations. 73, Rich VE3KI W3FPR wrote: Bret, > > You may have better luck with running the RF Gain full and adjusting > with the AF gain. That way the RX AGC will smooth out variations in > the > signal level. > > 73, > Don W3FPR > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to c...@murgatroid.com __ >>> Elecraft mailing list >>> Home: http://mailman.qth.net/mailman/listinfo/elecraft >>> Help: http://mailman.qth.net/mmfaq.htm >>> Post: mailto:Elecraft@mailman.qth.net >>> >>> This list hosted by: http://www.qsl.net >>> Please help support this email list: http://www.qsl.net/donate.html >>> Message delivered to jim.w4...@gmail.com >>> >>> >> __ >> Elecraft mailing list >> Home: http://mailman.qth.net/mailman/listinfo/elecraft >> Help: http://mailman.qth.net/mmfaq.htm >> Post: mailto:Elecraft@mailman.qth.net >> >> This list hosted by: http://www.qsl.net >> Please help support this email list: http://www.qsl.net/donate.html >> Message delivered to n...@bayland.net >> >> >> > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to k2av@gmail.com >
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
Can't help but wonder, is anyone adjusting the recording and playback in Windows? Mine works fine by adjusting those. I don't do any vhf though. 73 Dwight NS9I On 6/26/2017 7:59 PM, Jim Rogers wrote: Richard - I second your report, there is no fine adjustment for the USB audio on the K3s either in received audio or transmitted audio. When the band is noisy, I have to reduce LIN OUT to 01 or alternatively reduce the overall system gain with the RF gain (which in the case of the K3 and K3s is IF gain). When operating meteor scatter on 2M with an Elecraft K144XV transverter I had to reduce the audio drive from the JT65 software to 50% to prevent RF power out overshoot and hunting, typical in over-driven closed loop systems. This allowed me to advance LIN IN and the end result was the power detection system of the K3s settled down. There are work-arounds. Jim, W4ATK K-Line, K2/10 On 6/26/2017 6:11 PM, Christopher Hoover wrote: USB audio with the default settings has been fine for me from the first day. Check your settings? On Thu, Jun 22, 2017 at 10:31 AM, Dick via Elecraft < elecraft@mailman.qth.net> wrote: Hello Elecraft, When feeding the audio from the K3S USB port to the CPU, the K3S audio level is extremely high and way too hot for good performance on many digital modes. Example, even with my CPU's sound card set at the lowest possible level of "01" my K3S is hitting the JT-65 software with a super strong signal that is much higher than the software wants to see and performance is degraded. The same is true when operating RTTY using MMTTY or 2Tone software. The USB audio output on the K3S needs to be adjustable in the K3S Menu as it was on the K3 Serial port. I wrote to you a few months ago about this without a positive reply. Please address this serious issue. Thank you- Richard Van Zandt- K9OM In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, elecraft-requ...@mailman.qth.net writes: If you are using Line Out with a fixed gain setting to feed audio to WSJT-X, adjusting the AF control will not do anything. What I do is leave my RF gain control at its normal position (around 3 o'clock) and use the slider at the lower left in the WSJT-X window to compensate for gain variations. 73, Rich VE3KI W3FPR wrote: Bret, You may have better luck with running the RF Gain full and adjusting with the AF gain. That way the RX AGC will smooth out variations in the signal level. 73, Don W3FPR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to c...@murgatroid.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to jim.w4...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to n...@bayland.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
Richard - I second your report, there is no fine adjustment for the USB audio on the K3s either in received audio or transmitted audio. When the band is noisy, I have to reduce LIN OUT to 01 or alternatively reduce the overall system gain with the RF gain (which in the case of the K3 and K3s is IF gain). When operating meteor scatter on 2M with an Elecraft K144XV transverter I had to reduce the audio drive from the JT65 software to 50% to prevent RF power out overshoot and hunting, typical in over-driven closed loop systems. This allowed me to advance LIN IN and the end result was the power detection system of the K3s settled down. There are work-arounds. Jim, W4ATK K-Line, K2/10 On 6/26/2017 6:11 PM, Christopher Hoover wrote: USB audio with the default settings has been fine for me from the first day. Check your settings? On Thu, Jun 22, 2017 at 10:31 AM, Dick via Elecraft < elecraft@mailman.qth.net> wrote: Hello Elecraft, When feeding the audio from the K3S USB port to the CPU, the K3S audio level is extremely high and way too hot for good performance on many digital modes. Example, even with my CPU's sound card set at the lowest possible level of "01" my K3S is hitting the JT-65 software with a super strong signal that is much higher than the software wants to see and performance is degraded. The same is true when operating RTTY using MMTTY or 2Tone software. The USB audio output on the K3S needs to be adjustable in the K3S Menu as it was on the K3 Serial port. I wrote to you a few months ago about this without a positive reply. Please address this serious issue. Thank you- Richard Van Zandt- K9OM In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, elecraft-requ...@mailman.qth.net writes: If you are using Line Out with a fixed gain setting to feed audio to WSJT-X, adjusting the AF control will not do anything. What I do is leave my RF gain control at its normal position (around 3 o'clock) and use the slider at the lower left in the WSJT-X window to compensate for gain variations. 73, Rich VE3KI W3FPR wrote: Bret, You may have better luck with running the RF Gain full and adjusting with the AF gain. That way the RX AGC will smooth out variations in the signal level. 73, Don W3FPR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to c...@murgatroid.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to jim.w4...@gmail.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
USB audio with the default settings has been fine for me from the first day. Check your settings? On Thu, Jun 22, 2017 at 10:31 AM, Dick via Elecraft < elecraft@mailman.qth.net> wrote: > Hello Elecraft, > > When feeding the audio from the K3S USB port to the CPU, the K3S audio > level is extremely high and way too hot for good performance on many > digital > modes. > > Example, even with my CPU's sound card set at the lowest possible level of > "01" my K3S is hitting the JT-65 software with a super strong signal that > is much higher than the software wants to see and performance is degraded. > The same is true when operating RTTY using MMTTY or 2Tone software. > > The USB audio output on the K3S needs to be adjustable in the K3S Menu as > it was on the K3 Serial port. > > I wrote to you a few months ago about this without a positive reply. > Please address this serious issue. > > Thank you- > > Richard Van Zandt- K9OM > > > > In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, > elecraft-requ...@mailman.qth.net writes: > > If you are using Line Out with a fixed gain setting to feed audio to > WSJT-X, adjusting the AF control will not do anything. What I do is leave > my RF gain control at its normal position (around 3 o'clock) and use the > slider at the lower left in the WSJT-X window to compensate for gain > variations. > > 73, > Rich VE3KI > > W3FPR wrote: > > > Bret, > > > > You may have better luck with running the RF Gain full and adjusting > > with the AF gain. That way the RX AGC will smooth out variations in the > > signal level. > > > > 73, > > Don W3FPR > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to c...@murgatroid.com > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
There is a Lin Out setting in menu. Sent from my iPhone ...nr4c. bill > On Jun 22, 2017, at 1:31 PM, Dick via Elecraft > wrote: > > Hello Elecraft, > > When feeding the audio from the K3S USB port to the CPU, the K3S audio > level is extremely high and way too hot for good performance on many digital > modes. > > Example, even with my CPU's sound card set at the lowest possible level of > "01" my K3S is hitting the JT-65 software with a super strong signal that > is much higher than the software wants to see and performance is degraded. > The same is true when operating RTTY using MMTTY or 2Tone software. > > The USB audio output on the K3S needs to be adjustable in the K3S Menu as > it was on the K3 Serial port. > > I wrote to you a few months ago about this without a positive reply. > Please address this serious issue. > > Thank you- > > Richard Van Zandt- K9OM > > > > In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, > elecraft-requ...@mailman.qth.net writes: > > If you are using Line Out with a fixed gain setting to feed audio to > WSJT-X, adjusting the AF control will not do anything. What I do is leave > my RF gain control at its normal position (around 3 o'clock) and use the > slider at the lower left in the WSJT-X window to compensate for gain > variations. > > 73, > Rich VE3KI > > W3FPR wrote: > >> Bret, >> >> You may have better luck with running the RF Gain full and adjusting >> with the AF gain. That way the RX AGC will smooth out variations in the >> signal level. >> >> 73, >> Don W3FPR > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to n...@widomaker.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3S USB audio output needs to be adjustable in Menu
See the CONFIG Menu, LIN OUT to adjust level. Normal is 010. 73 Bob, K4TAX K3S S/N 10163 On 6/22/2017 12:31 PM, Dick via Elecraft wrote: Hello Elecraft, When feeding the audio from the K3S USB port to the CPU, the K3S audio level is extremely high and way too hot for good performance on many digital modes. Example, even with my CPU's sound card set at the lowest possible level of "01" my K3S is hitting the JT-65 software with a super strong signal that is much higher than the software wants to see and performance is degraded. The same is true when operating RTTY using MMTTY or 2Tone software. The USB audio output on the K3S needs to be adjustable in the K3S Menu as it was on the K3 Serial port. I wrote to you a few months ago about this without a positive reply. Please address this serious issue. Thank you- Richard Van Zandt- K9OM In a message dated 6/2/2017 7:28:48 P.M. Central Daylight Time, elecraft-requ...@mailman.qth.net writes: If you are using Line Out with a fixed gain setting to feed audio to WSJT-X, adjusting the AF control will not do anything. What I do is leave my RF gain control at its normal position (around 3 o'clock) and use the slider at the lower left in the WSJT-X window to compensate for gain variations. 73, Rich VE3KI W3FPR wrote: Bret, You may have better luck with running the RF Gain full and adjusting with the AF gain. That way the RX AGC will smooth out variations in the signal level. 73, Don W3FPR __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to rmcg...@blomand.net __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com