My K3 has developed a problem with the VFO. It is, of course, just
barely out of warranty. :-)
When I turn the VFO knob very slowly, the frequency display follows
normally, but when I turn it a little faster, the frequency display
freezes and intermittently unfreezes but immediately freezes agai
ORIGINAL MESSAGE (may be snipped)
On Fri, 13 Feb 2015 23:55:13 -0600, Dave wrote:
>
>Sounds to me that you have something grabbing big chunks of CPU time.
>What all is plugged into the K3? Clear everything out. See if that
>helps. If so, then replug things until the beh
An encoder problem?
Phil W7OX
On 2/14/15 12:53 AM, Bill Turner wrote:
ORIGINAL MESSAGE (may be snipped)
On Fri, 13 Feb 2015 23:55:13 -0600, Dave wrote:
Sounds to me that you have something grabbing big chunks of CPU time.
What all is plugged into the K3? Clear everyt
I would suggest it's worth the time to swap the VFO A and VFO B
encoder boards. It could be the encoder itself or its contacts to the
front panel board, either of them.
If you take this course, you might want to check the encoder board
contacts on each of them, and also take a look at the contact
I think you are on to something, Matt. On a hunch, I performed a
"percussive reset" as NASA calls it. I lifted the front on the K3
about an inch and dropped it. The problem went away for now. When it
comes back, I will do as you suggest.
Many thanks to all who replied.
Bill W6WRT
---
Percussive resets are well-known for finding a general problem area.
They don't localize it, but it's a start.
Good luck with this. An encoder board "SOL" problem happened to me
about five years ago, and I followed the same advice I gave you (which
came from someone else). :}
73,
matt
W6NIA
On
This was a standard technique used by TV repairmen back in the days of tube
consoles and house calls. For intermittent problems one waited until the owner
left the room then lifted up one side about 6 inches and let it drop. Usually
either fixed the problem or caused a hard fault that could be
My grandfather (Ex K4GF, SK) was a TV repairman during the tube TV era.
The most common fault requiring a house call was the housewife not
plugging the TV back in after she unplugged it to vacuum
73, Ross N4RP
On 2/14/2015 12:29 PM, David Christ wrote:
This was a standard technique used
The charge was $100.
“$100?” the TV owner questioned. “All you did was plug it in.”
Repairman: “That was $5. The other $95 was for knowing what to do.”
73 - Steve WB6RSE
> On Feb 14, 2015, at 9:34 AM, Ross Primrose wrote:
>
> My grandfather (Ex K4GF, SK) was a TV repairman during the tube TV er
My father, W1BML used to repair TVs and radios after his work was
over back in the 50's in PA, he was the go to guy back then to have
electronics repaired (was W8QXF & then W3QXF when the area changed).
I remember going with him on a house call and the unplugged TV was
the problem. He wouldn't
robing.
73, Ed - KL7UW
Date: Sat, 14 Feb 2015 12:34:04 -0500
From: Ross Primrose
Cc: Elecraft
Subject: Re: [Elecraft] VFO problem
Message-ID: <54df870c.1020...@n4rp.com>
Content-Type: text/plain; charset=windows-1252; format=flowed
My grandfather (Ex K4GF, SK) was a TV repairman duri
Ed - KL7UW Wrote: "Rules for troubleshooting: what are the symptoms
(what is not working), check power inputs; check configurations
(settings); look-feel-sniff; measure for required output - then get out
the manual/schematic/tools. An "old" tech once advised me that most
problems were simple
ORIGINAL MESSAGE (may be snipped)
On Sat, 14 Feb 2015 13:05:45 -0900, you wrote:
>
>Rules for troubleshooting: what are the symptoms (what is not
>working), check power inputs; check configurations (settings);
>look-feel-sniff; measure for required output - then get out
’Tis true that doing a reset can cause a problem to go away and is often the
only way out — but a reset should not be the first remedy tried. When I was
part of a network group responsible for a nationwide data/voice network we had
a co-worker that drove us nuts. His solution to any problem wa
On 02/14/2015 09:34 AM, Ross Primrose wrote:
My grandfather (Ex K4GF, SK) was a TV repairman during the tube TV
era. The most common fault requiring a house call was the housewife
not plugging the TV back in after she unplugged it to vacuum
A friend's father was a service technician for F
15 matches
Mail list logo