Hello,
I would like to compute the battery level of my iris mote. I am using the
function VoltageC of mica. I would like to know the conversion formula from ADC
readings to Voltios for IRIS motes. It seems that it is not the same that for
mica motes.
Thank you very much.
Yours,
Sofia
Hello,
I have an IRIS mote with some sensors and using CTP algorithm
and it lasted around 2 days and a half. If I use LPL with 500 ms
or 1000ms it lasted around 5 days. Is it possible to increase
the lifetime of the motes using CTP protocol?
Hello,
I am using a network composed of 3 IRIS motes + a base station with a MIB520
getaway connected to a PC. Each mote is sending 8 messages of 100 bytes each 30
seconds. I am using Matlab to read the data from the USB. I was using a
baudrate of 57600 but after some hours I stop receiving dat
Hello,
I am using mica2 motes and ctp algorithm and I would like to have 2 different
networks working at the same time.
I have tried to use different DEFAULT_LOCAL_GROUP for each network changing
this value in the makefile and it is not working. Both base stations receive
all messages.
I al
Hello,
I would like to use an analog Omron D6F-V03A1 model air
sensor with Tinyos2 and Mica2. How can I do that? Is there any example
about how to read data from an analog sensor?
Thank you very much!
Sofia
___
Hello,
I would like to use an analog Omron D6F-V03A1 model air sensor with Tinyos2 and
Mica2. How can I do that? Is there any example about how to read data from an
analog sensor?
Thank you very much!
Sofia
Hello,
I would like to know how to change the output RF power to the maximum for Mica2
motes at 433 Mhz and at 918Mhz.
I have seen that the default RF power value is 0x0F (0dBm at 433, -6dBm at
916). I have seen in the CC1000 datasheet that the maximum output power is FF.
How many dbm corr
Hello,
I would like to measure the RSSI values in dBm with Mica2 and IRIS motes.
I have tried with Mica2 motes and with output power of 0B, when they are close
I obtain a value around 20 but when they are far away I get a values around
160. I would like to know how to convert these values to
Hello,
I am sending a message every 5 minutes with mica2 motes and I use CTP. Since I
would like to reduce the power consumption.
I want to know which values should I choose to use the LPL:
CFLAGS += -DLOW_POWER_LISTENING
CFLAGS += -DLPL_DEF_LOCAL_WAKEUP=512
CFLAGS += -DLPL_DEF_REMOTE_W
Hello,
I would like to know how much time a node needs to reconfigure the route with
CTP because a problem happens with its father.
In the ctp paper appears that:
"It maintains a beaconing interval which
varies between 64ms and one hour. Whenever the timer expires,
CTP doubles it, up to the m
Hello,
I would like to know how can I get the battery left in my mica2 or iris mote.
Thank you.
Sofia
___
Tinyos-help mailing list
Tinyos-help@millennium.berkeley.edu
https://www.millennium.berkeley.edu/cgi-b
Hello,
I would like to know the transmission velocity of I2C in
an IRIS mote. I have read that there is a fast (400) and a standard mode
(100). Can I choose between these velocities? How can I do that?
Thank you very much.
Sofia
Hello,
I would like to know if it is possible to configure two differents networks
with iris motes and working at the same time.
Thank you very much.
Sofia
___
Tinyos-help mailing list
Tinyos-help@millenniu
Hello,
I would like to know if it is possible to use an iris mote as a I2C slave. How
can I do that?
Thank you very much.
Sofia
___
Tinyos-help mailing list
Tinyos-help@millennium.berkeley.edu
https://www.m
Hello,
I want to connect a FIFO to an IRIS mote using a MDA100 sensor board and I
would like to read the data received from the FIFO using the I2C connector. It
is the first time that I have to do something like that. Could you please
explain to me what do I need to do? Do you know any exam
Hello,
I would like to know if somebody has used the IBM mote runner enviromment with
IRIS motes. Do you recommend to use it?
I have being working with tinyos-2.x and iris motes using cygwin.
Thank you very much.
Sofia
_
Hello,
I want to connect a FIFO to an IRIS mote using a MDA100 sensor board and I
would like to read the data received from the FIFO using the I2C connector. It
is the first time that I have to do something like that. Could you please
explain to me what do I need to do? Do you know any examp
o access the interrupt vectors directly.
>
> Cheers,
> Urs
>
>
> On 02/02/2011 09:21 AM, sofia aparicio wrote:
> > Hello,
> >
> > Using AVR_ATOMIC_HANDLER(SIG_INTERRUPT1) I get the same error:
> >
> > In component `UltrasoundControlM':
> > /
-szeged.hu
> To: aparicioso...@hotmail.com
> CC: tinyos-help@millennium.berkeley.edu
>
> Hi Sofia,
>
> Use
>
> AVR_ATOMIC_HANDLER(SIG_INTERRUPT1) {
> }
>
> Miklos
>
>
> On Tue, Feb 1, 2011 at 1:21 PM, sofia aparicio
> wrote:
> >
> > Hell
Hello,
I would like to define an external interrupt in INT1 pin. When I call the
interrupt a get an error message.
1) If I use :
ISR(INT1_vect){
}
I get the following error:
In component `UltrasoundControlM':
/opt/tinyos-2.x_Cricket_iris/tos/platforms/iris/UltrasoundControlM.nc:823: use (
),
Hello,
> Seems ok, but not sure how you access those pins. How did you verified
> that your code does not work? You cannot be sure that these pins are
> available on the 51-pins.
I am using a MDA100 sensor board connected to my IRIS mote. I can see the
signals in OC3A, OC3B and OC3C using an
Hello,
I would like to configure in Fast PWM mode without prescaler and toggling
OCR3A,OCR3B and OCR3C at the same time. I do the following:
SET_BIT(DDRE,3); OCR3A
SET_BIT(PORTE,3);
SET_BIT(DDRE,4); OCR3B
SET_BIT(PORTE,4);
SET_BIT(DDRE,5); OCR3C
SET_BIT(PORTE,5);
TCCR3A=0x57;
TCCR3B=0x19;
OCR
ring of TOS1.x showed that TimerM used Timer0
> > and the micaz TimerJiffy used Timer2, so I was able to use Timer1
> > for PWM outputs. My timer code is here if it's any help:
> > http://www.etantdonnes.com/Motes/AVR128timers.zip
> >
> > MS
> >
> >
.x showed that TimerM used Timer0
> > and the micaz TimerJiffy used Timer2, so I was able to use Timer1
> > for PWM outputs. My timer code is here if it's any help:
> > http://www.etantdonnes.com/Motes/AVR128timers.zip
> >
> > MS
> >
> > sofia aparicio wr
Hello,
I am using IRIS mote and I have a main program where I call a TimerMilliC. This
timer is fired every 10 seconds. Then I would like to use the OC1A using a
MDA100 sensor board.
If I undestood well this pin is available. Then, I configure this OC1A in CTC
mode using
TCCR1A=0x40; TCCR1B=
Hello,
I am using Motewoks. I would like to use the MDA sensor board with a micaz
mote. I have added a temperature/humidity sensor from Sensirion in the
prototype area (in an open pin). I would like to know how can I access the
value of this sensor. For tinyos-2.x I have seen the drivers for
Hello,
I would like to send a integer value from my computer (using Matlab) to a mica2
mote using the serial port and TinyOS-2.x.
How can I do that? Do you know any example? With TinyOS-1.x I could do it with
the function:
event result_t SerialM.Receive(char * buf, uint8_t data_len)
mers in the new version of TinyOS-2.x
From: p...@cs.stanford.edu
Date: Thu, 20 May 2010 17:25:27 -0700
CC: tinyos-help@millennium.berkeley.edu
To: aparicioso...@hotmail.com
On May 19, 2010, at 7:09 AM, sofia aparicio wrote:
Hello,
I would like to know if there were changes with timers in the
te: Thu, 20 May 2010 17:25:27 -0700
CC: tinyos-help@millennium.berkeley.edu
To: aparicioso...@hotmail.com
On May 19, 2010, at 7:09 AM, sofia aparicio wrote:
Hello,
I would like to know if there were changes with timers in the new version of
TinyOS-2.x
I have a program where I used timer 1 an
ion of TinyOS-2.x
I got the following error:
/opt/tinyos-2.x/tos/chips/atm128/timer/HplAtm128Timer1P.nc:195: previous declara
tion of `__vector_12'
/opt/tinyos-2.x/tos/chips/atm128/timer/HplAtm128Timer1P.nc:207: previous declara
tion of `__vector_11'
Thank you ve
Hello,
I would like to know what should I do to download something using CVS. I am
uisng cygwin and I obtain the following error:
$ cvs -z3 -d:pserver:anonym...@tinyos.cvs.sourceforge.net:/cvsroot/tinyos co -P
tinyos-1.x
cvs [checkout aborted]: connect to tinyos.cvs.sourceforge.net(216.3
Hello,
I am using ctp library with 4 mica2 motes (1 is the root and 3 are the
producers). I have an application that every 4 minutes sends some temperature
measurements to the root. The application with micaz is working perfectly. But
if I use mica2 motes, the root stops receiving data of som
Hello,
I would like to know if XMesh works with TinyOS-1.x and -2.x and using the
mica2 platform.
Thank you very much.
Sofia
> From: gnaw...@cs.stanford.edu
> Date: Sat, 20 Feb 2010 15:25:23 -0800
> To: mongoose_r...@mail.ru
> CC: tinyos-help@millennium.berkeley.edu
> Subject: Re: [
components. If you need custom debug messages, then you need to add your
corresponding debug msg types into the CtpDebugMsg.h / CollectionDebugMsg.h and
call CollectionDebug functions with those types that you added where you need.
Regards,
--
Mehmet Akif Antepli
On Tue, Feb 9, 2010 at
Hello,
I am using CTP with 4 mica2. One mica2 is the base station and the remaining
motes are computing some temperature measurements every 2 minutes and sending
this information to the base station. After some hours the nodes lose the route
since the parent ids change to strange ids which do
Hello,
I would like to know if TOSSIM is working with mica2. Otherwise, how can I see
the dbg messages?
Thank you very much.
Sofia
_
Los auténticos Hotmail y Messenger en tu Blac
tmail.com
> CC: tinyos-help@millennium.berkeley.edu
>
> As far as I know, LPL is not implemented for mica2 in Tinyos 2.x.
>
> Janos
>
> On Tue, Feb 2, 2010 at 6:01 AM, sofia aparicio
> wrote:
> >
> > Hello,
> >
> > I want to use LPL with Mica2 mot
Hello,
I want to use LPL with Mica2 motes. I have added to my code the following:
In my boot function:
LPL.setLocalSleepInterval(2000);
Before sending a packet:
LPL.setRxSleepInterval(&pkt,2000);
Send.send(&pkt,sizeof());
This is not working, I can not see the cycles. Do you kn
ey.edu
>
> On Mon, Nov 2, 2009 at 3:07 AM, sofia aparicio
> wrote:
> >
> > Hello,
> >
> > I am trying to use CTP algorithms on mica2 but they are not working
> > correctly. It seems that a msg is sent successfully but it did not call the
> > function
and
green.
Do you know what it is happening?
Thanks,
Sofia
> Date: Tue, 3 Nov 2009 19:01:38 -0800
> Subject: Re: [Tinyos-help] CTP and mica2 on TinyOS-2.x
> From: gnaw...@cs.stanford.edu
> To: aparicioso...@hotmail.com
> CC: tinyos-help@millennium.berkeley.edu
>
> On Mon
Thanks,
Sofia
> Date: Tue, 3 Nov 2009 19:01:38 -0800
> Subject: Re: [Tinyos-help] CTP and mica2 on TinyOS-2.x
> From: gnaw...@cs.stanford.edu
> To: aparicioso...@hotmail.com
> CC: tinyos-help@millennium.berkeley.edu
>
> On Mon, Nov 2, 2009 at 3:07 AM, sofia ap
Hello,
Could you please help with this?
I am trying to use CTP algorithms on mica2 but they are not working correctly.
It seems that a msg is sent successfully but it did not call the function
senddone.
I am testing the application MultihopOscilloscope with 2 motes, a base station
(id 0) a
Hello,
I am trying to use CTP algorithms on mica2 but they are not working correctly.
It seems that a msg is sent successfully but it did not call the function
senddone.
I am testing the application MultihopOscilloscope with 2 motes, a base station
(id 0) and another one (id 1).
Do you
Hello,
I would like to upgrade the libraries from my TinyOS-2.x from:
http://www.tinyos.net/tinyos-2.x/
How can I do this using Cygwin?
Thanks,
Sofia
_
Vive toda la expe
Hello,
I am trying to use cricket in TOS2.x. I have created a cricket platform. I have
installed the Blink application to my cricket and it was working.
Then I tried to do the same with the Oscilloscope application, but when I
installed the application, the mote did not do anything.
I hav
Hello,
I would like to know if I can use the following functions in tinyOS-2.x:
outp(port,value)
sbi(port,value)
cbi(port,value)
outw()
I have used them in TinyOS-1.x.
Thanks,
Sofia
Hello,
I am trying to change my mote to "power save mode" in the cricket application.
I write in CricketM.nc module the following:
sbi(ASSR, AS0);
sbi(MCUCR, SM0);
sbi(MCUCR, SM1);
sbi(MCUCR, SE);
This is not working. I am consuming around 10 mA, the same quantity that
without thes
Hello,
I would like to know which protocol is using the cricket application for
TinyOS1.x.
I have seen that there are different protocols S-MAC, B-MAC, ...
Thank you very much.
Sofia
__
Hello,
I tried to compile the Cricket application using TOSSIM but I get an error.
When I typed:
make pc
I obtain something like that:
.
.
.
.
InternalEEPROMM.nc:36:24: avr/eeprom.h: No such file or directory
InternalEEPROMC.nc:40: failed to preprocess InternalEEPROMM.nc
Inte
Hello,
I would like to send some information from a Cricket mote to a Micaz mote using
a serial port.
Is it possible to do that? How can I do that?
Thank you very much.
Sofia
¿Quieres que tus amigos de Messenger sigan tus movimientos de Facebook?
¡Conéctalos ya!
Hello,
I have mote in power save mode. A send a radio msg when the mote is sleeping.
I would like to know if he receives the information when he wakes up.
Thank you very much.
Sofia
Hay tantos ordenadores como personas. ¡Descubre ahora cuál eres tú!
Hello,
I have mote in power save mode. A send a radio msg when the mote is sleeping.
I would like to know if he receives the information when he wakes up.
Thank you very much.
Sofia
_
Con Vodafone disfruta de Hotmail
Hello,
I would like to send some information from a Cricket mote to a Micaz mote using
a serial port.
Is it possible to do that? How can I do that?
Thank you very much.
Sofia
_
Hay tantos ordenadores como personas. ¡D
Hello,
I left several hours running 3 motes and 1 base station. I am using the Route
library. I have seen that I receive information from every mote but suddenly I
do not receive anything from one mote. After 2 hours I start receiving again
from this mote. This is happening with the 3 motes
otmail.com
> CC: tinyos-help@millennium.berkeley.edu
>
> On Wed, Jul 22, 2009 at 5:07 AM, sofia
> aparicio wrote:
> >
> > Hello,
> >
> > I am using the Route library. I would like to know how to send a msg from
> > the base station to the other motes.
Hello,
I have a problem with Route library in tinyos1.x. I am using 2 motes and 1 base
station.
If I put this 2 motes close to the base station then I receive the information
from both motes. But if I put mote 2 out of the radio range of the base
station, and I put mote 1 between mote 2
e exactly what is coming over the "wire",
> and then work out from there.
>
> MS
>
> sofia aparicio wrote:
> >
> >
> > Hello,
> >
> > I would like to know what is the crc of a TOS_msg.
> > I am sending a msg using radio a
Hello,
I am using the Route library. I would like to know how to send a msg from the
base station to the other motes.
Thank you very much.
Sofia
_
Chatea sin límites en Messenger con la tarifa plana de Orange
http://se
Hello,
I would like to know what is the crc of a TOS_msg.
I am sending a msg using radio and I should receive
tla:1, distance: 1592, temp: 28
but I am receiving something like that:
:=¡~tla: 1,distanc~Be}:^ 15}9]2,tempú: 28
How can I fix this?
Thank you very much.
Sofia
Hello,
I would like to know what is the crc of a TOS_msg.
I am sending a msg using radio and I should receive
tla:1, distance: 1592, temp: 28
but I am receiving something like that:
:=¡~tla: 1,distanc~Be}:^ 15}9]2,tempú: 28
How can I fix this?
Thank you very much.
Hello,
I want to send several messages from different motes to the base station (mote
0) using the Route library.
When the base station receives the message I want to print it. How can I do
this? Which function shall I use to do that receive or intercept?
I do the following:
compo
Hello,
I want to send several radio messages using BareSendMsg.send.
If I write something like that it does not work:
timer.fired()
{
result= call BareSendMsg.send(msg);
wait(10 seconds);
result1=BareSendMsg.send(msg);
if (result==SUCCESS) leds red on;
if (result1== SUCCESS)
Hello,
Could you please tell me the difference between "async event" and "event"?
When a "event" is executed?
Thank you very much,
Sofia
Comparte tus fotos con tus amigos. Más fácil con Windows Live
_
Llévate Messenger
Hello,
Could you please tell me the difference between "async event" and "event"?
When a "event" is executed?
Thank you very much,
Sofia
_
¿Quieres ver los mejores videos de MSN? Enciende Messenger TV
http://messenger
Hello,
I have 3 motes and I want to send data from mote 2 trough mote 1 to the base
station.
Mote 2 call RadioSend.send(data);
RadioReceive.receive(){
if (TOS_LOCAL_ADDRESS == 1){
call RadioSend.send(data); //Send data to base station (mote 0).
}
if (TOS_LO
Hello,
When I receive a radio message I want to send the received information through
the serial port using UARTOutput function.
I would like to know if there is any restriction about the quantity I can send
through the serial port.
If I try to do the following in the event TOS_MsgPtr
Ra
Hello,
I would like to know what do I need to do to send and receive a message using
the protocols of the Route library. Do I need to asociate every TOS_Msg with a
TOS_MHopMsg? In Surge example they do the following:
if (pReading = (SurgeMsg *)call Send.getBuffer(&gMsgBuffer,&Len)) {
Hello,
I have some questions about the routing protocols with Cricket motes. I am
trying to construct an application with 1 base station connected to a computer
through a serial port and several motes. I want these motes to send some
information to the base station using the Route library.
estion about rounting protocols for tinyos-1.x
> From: gnaw...@usc.edu
> To: aparicioso...@hotmail.com
> CC: tinyos-help@millennium.berkeley.edu
>
> On Tue, Jun 16, 2009 at 3:28 AM, sofia
> aparicio wrote:
> > Hello,
> >
> > I am using Cricket motes and I
Hello,
I am using Cricket motes and I want to create a wireless network. I have
several motes but only 1 base station. I need a routing protocol to send the
information from every mote to the base station. Sometimes the mote is far from
the station and data has to be send through other mote
70 matches
Mail list logo