Re: Recovering SP node to Standalone RS6000
I was told that sysback would recognize the hardware and not install the PSSP stuff. Well, the customer I support fail to ask for input, and subscribed to all standalones. This is the only SP server that needs to be recovered. It is a limited DR test. -Original Message- From: Kauffman, Tom [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 3:32 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 It's been a while since my SP frames went away, so take this with a grain of salt - - At one point, sysback could not be used to 'clone' an AIX system; you needed a mksysb image (and the install cd). I don't know if this has changed. I do know from experience that the system you will be restoring to at the hotsite won't match your contract spec (it will be at least as good as, and possibly better -- like no 10 Mb ethernet, just 10/100 Mb, with different device drivers). Also, with no CWS, you'll need to research how to disable most of the PSSP code on the node. Code that, among other things, does a node lookup in the SDR (on the CWS) to get the IP addresses for your network connections. This may take some doing (my experience ends at PSSP 3.2). Is this the ONLY SP node you need to recover? Or is this a case of "our recovery site doesn't have an SP"? I've done stand-alone recoveries and SP recoveries, but I've never tried to do a crossover like this. Tom Kauffman NIBCO, Inc > -Original Message- > From: Jolley, Bill [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 1:28 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > I cannot use NIM because I will not have access to the NIM > server at the DR > site. > > -Original Message- > From: Daniel Whicker [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 2:06 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > Bill, your colleague was correct, you can restore a non > bootable mksysb > tape using an install cd. As opposed to doing that, though, > just backup > your mksysb to a file on your CWS, and then use NIM to restore that > mksysb onto your new node. It will handle the tough stuff > for ya. You > can also do a savevg for all non-rootvg vgs. Still doesn't > get any raw > devices though, like SysBack will. > > On Thu, 2002-05-02 at 12:40, Jolley, Bill wrote: > > No, I do not have a tape drive attached to the SP node. I > have introduced > > AIX sysback as an alternative. Several colleagues stated > that you could > > boot from cdrom and use the image on tape as input and > basically I am > > restored. I disagreed. But thanks. Sysback appears to be > much easier than > > jumping through hoops. > > > > -Original Message- > > From: David Longo [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, May 02, 2002 1:07 PM > > To: [EMAIL PROTECTED] > > Subject: Re: Recovering SP node to Standalone RS6000 > > > > > > Do you have a tape drive physically attached to the SP node? > > If so then you can do fairly easily. If not then I think you need > > AIX Sysback to make a mksysb to a remote tape. You can't make > > a mksysb image to disk and then copy that image to tape - it's > > not a bootable image. > > > > David Longo > > > > >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> > > Here is what I need to accomplish or would like to. Create > a mksysb of > the > > SP Node, copy the image to media. At the recovery site, I > will need to > > restore this image to the standalone rs6000. I do not know > if this is > > possible even if I use the cloning process. > > > > > > -Original Message- > > From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, May 02, 2002 12:30 PM > > To: [EMAIL PROTECTED] > > Subject: Re: Recovering SP node to Standalone RS6000 > > > > > > Connect to node and say shutdown -m > > > > > > -Original Message- > > From: Jolley, Bill [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, May 02, 2002 10:52 AM > > To: [EMAIL PROTECTED] > > Subject: Recovering SP node to Standalone RS6000 > > > > > > I have a TSM server located on an IBM SP Node (winterhawk) > and would like > to > > recover to a standalone RS/6000 (H80). Do anyone have/know > of a procedure > or > > have suggestions? > > > > Thanks, > > > > Bill Jolley > > EDS SS-SEMainframe Services > > Telephone:704-548-5524 > > Email:[EMAIL PROTECTED] > > Pager:704-354-6967 > > &
Re: Recovering SP node to Standalone RS6000
It's been a while since my SP frames went away, so take this with a grain of salt - - At one point, sysback could not be used to 'clone' an AIX system; you needed a mksysb image (and the install cd). I don't know if this has changed. I do know from experience that the system you will be restoring to at the hotsite won't match your contract spec (it will be at least as good as, and possibly better -- like no 10 Mb ethernet, just 10/100 Mb, with different device drivers). Also, with no CWS, you'll need to research how to disable most of the PSSP code on the node. Code that, among other things, does a node lookup in the SDR (on the CWS) to get the IP addresses for your network connections. This may take some doing (my experience ends at PSSP 3.2). Is this the ONLY SP node you need to recover? Or is this a case of "our recovery site doesn't have an SP"? I've done stand-alone recoveries and SP recoveries, but I've never tried to do a crossover like this. Tom Kauffman NIBCO, Inc > -Original Message- > From: Jolley, Bill [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 1:28 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > I cannot use NIM because I will not have access to the NIM > server at the DR > site. > > -Original Message- > From: Daniel Whicker [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 2:06 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > Bill, your colleague was correct, you can restore a non > bootable mksysb > tape using an install cd. As opposed to doing that, though, > just backup > your mksysb to a file on your CWS, and then use NIM to restore that > mksysb onto your new node. It will handle the tough stuff > for ya. You > can also do a savevg for all non-rootvg vgs. Still doesn't > get any raw > devices though, like SysBack will. > > On Thu, 2002-05-02 at 12:40, Jolley, Bill wrote: > > No, I do not have a tape drive attached to the SP node. I > have introduced > > AIX sysback as an alternative. Several colleagues stated > that you could > > boot from cdrom and use the image on tape as input and > basically I am > > restored. I disagreed. But thanks. Sysback appears to be > much easier than > > jumping through hoops. > > > > -Original Message- > > From: David Longo [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, May 02, 2002 1:07 PM > > To: [EMAIL PROTECTED] > > Subject: Re: Recovering SP node to Standalone RS6000 > > > > > > Do you have a tape drive physically attached to the SP node? > > If so then you can do fairly easily. If not then I think you need > > AIX Sysback to make a mksysb to a remote tape. You can't make > > a mksysb image to disk and then copy that image to tape - it's > > not a bootable image. > > > > David Longo > > > > >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> > > Here is what I need to accomplish or would like to. Create > a mksysb of > the > > SP Node, copy the image to media. At the recovery site, I > will need to > > restore this image to the standalone rs6000. I do not know > if this is > > possible even if I use the cloning process. > > > > > > -Original Message- > > From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, May 02, 2002 12:30 PM > > To: [EMAIL PROTECTED] > > Subject: Re: Recovering SP node to Standalone RS6000 > > > > > > Connect to node and say shutdown -m > > > > > > -Original Message- > > From: Jolley, Bill [mailto:[EMAIL PROTECTED]] > > Sent: Thursday, May 02, 2002 10:52 AM > > To: [EMAIL PROTECTED] > > Subject: Recovering SP node to Standalone RS6000 > > > > > > I have a TSM server located on an IBM SP Node (winterhawk) > and would like > to > > recover to a standalone RS/6000 (H80). Do anyone have/know > of a procedure > or > > have suggestions? > > > > Thanks, > > > > Bill Jolley > > EDS SS-SEMainframe Services > > Telephone:704-548-5524 > > Email:[EMAIL PROTECTED] > > Pager:704-354-6967 > > > > <> > > > > > > > > "MMS " made the following > > annotations on 05/02/02 13:21:23 > > > -- > -- > > -- > > This message is for the named person's use only. It may contain > > confidential, proprietary, or legally privileged information. No > > confidentiality or privil
Re: Recovering SP node to Standalone RS6000
You will want to use the CDROM to boot from, that saves you having to put the required code that is needed for your "disaster" machine on your current SP node. How that works is (briefly): Boot from CDROM, get to where it says something like "System Recovery" or Recover from mksysb tape - It's been a while since I've done it. At the point where you select the tape device, THEN insert the mksysb tape in drive and continue. What happens is it restores mksysb and at point where you need certain code (like uniprocessor code on a uniprocessor machine and your original machine was MP) then it pulls that code off the CDROM. This means you can take a mksysb tape from any RS/6000 or and restore to any other RS/6000, regardless of processor class or hardware. Important point to mention is that the CDROM has to be at same OS level as the mksysb tape - the original machine! You can spend time figuring what filesets would be needed for target machine and install them on current machine, but this takes detailed examination and you can miss something. And the machine you restore to in a disaster may not be what you had planned on etc. etc. BTW: For rebuilding an AIX machine, the TSM backup is not enough, you need a mksysb tape (or if restoring an SP node, the image on the Control Workstation) to do base restore first. Or a 3rd party product like Bare Metal Restore from The Kernel Group I think does this without a mksysb tape. Hope this helps some. David B. Longo System Administrator Health First, Inc. 3300 Fiske Blvd. Rockledge, FL 32955-4305 PH 321.434.5536 Pager 321.634.8230 Fax:321.434.5525 [EMAIL PROTECTED] >>> [EMAIL PROTECTED] 05/02/02 01:40PM >>> No, I do not have a tape drive attached to the SP node. I have introduced AIX sysback as an alternative. Several colleagues stated that you could boot from cdrom and use the image on tape as input and basically I am restored. I disagreed. But thanks. Sysback appears to be much easier than jumping through hoops. -Original Message- From: David Longo [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 1:07 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Do you have a tape drive physically attached to the SP node? If so then you can do fairly easily. If not then I think you need AIX Sysback to make a mksysb to a remote tape. You can't make a mksysb image to disk and then copy that image to tape - it's not a bootable image. David Longo >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> Here is what I need to accomplish or would like to. Create a mksysb of the SP Node, copy the image to media. At the recovery site, I will need to restore this image to the standalone rs6000. I do not know if this is possible even if I use the cloning process. -Original Message- From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 12:30 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Connect to node and say shutdown -m -Original Message- From: Jolley, Bill [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 10:52 AM To: [EMAIL PROTECTED] Subject: Recovering SP node to Standalone RS6000 I have a TSM server located on an IBM SP Node (winterhawk) and would like to recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or have suggestions? Thanks, Bill Jolley EDS SS-SEMainframe Services Telephone:704-548-5524 Email:[EMAIL PROTECTED] Pager:704-354-6967 <> "MMS " made the following annotations on 05/02/02 13:21:23 -- This message is for the named person's use only. It may contain confidential, proprietary, or legally privileged information. No confidentiality or privilege is waived or lost by any mistransmission. If you receive this message in error, please immediately delete it and all copies of it from your system, destroy any hard copies of it, and notify the sender. You must not, directly or indirectly, use, disclose, distribute, print, or copy any part of this message if you are not the intended recipient. Health First reserves the right to monitor all e-mail communications through its networks. Any views or opinions expressed in this message are solely those of the individual sender, except (1) where the message states such views or opinions are on behalf of a particular entity; and (2) the sender is authorized by the entity to give such views or opinions. == "MMS " made the following annotations on 05/02/02 14:45:00 -- This message is for the named person's use only. It may contain confidential, proprietary, or legally privileged information. No confi
Re: Recovering SP node to Standalone RS6000
I cannot use NIM because I will not have access to the NIM server at the DR site. -Original Message- From: Daniel Whicker [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 2:06 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Bill, your colleague was correct, you can restore a non bootable mksysb tape using an install cd. As opposed to doing that, though, just backup your mksysb to a file on your CWS, and then use NIM to restore that mksysb onto your new node. It will handle the tough stuff for ya. You can also do a savevg for all non-rootvg vgs. Still doesn't get any raw devices though, like SysBack will. On Thu, 2002-05-02 at 12:40, Jolley, Bill wrote: > No, I do not have a tape drive attached to the SP node. I have introduced > AIX sysback as an alternative. Several colleagues stated that you could > boot from cdrom and use the image on tape as input and basically I am > restored. I disagreed. But thanks. Sysback appears to be much easier than > jumping through hoops. > > -Original Message- > From: David Longo [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 1:07 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > Do you have a tape drive physically attached to the SP node? > If so then you can do fairly easily. If not then I think you need > AIX Sysback to make a mksysb to a remote tape. You can't make > a mksysb image to disk and then copy that image to tape - it's > not a bootable image. > > David Longo > > >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> > Here is what I need to accomplish or would like to. Create a mksysb of the > SP Node, copy the image to media. At the recovery site, I will need to > restore this image to the standalone rs6000. I do not know if this is > possible even if I use the cloning process. > > > -Original Message- > From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 12:30 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > Connect to node and say shutdown -m > > > -Original Message- > From: Jolley, Bill [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 10:52 AM > To: [EMAIL PROTECTED] > Subject: Recovering SP node to Standalone RS6000 > > > I have a TSM server located on an IBM SP Node (winterhawk) and would like to > recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or > have suggestions? > > Thanks, > > Bill Jolley > EDS SS-SEMainframe Services > Telephone:704-548-5524 > Email:[EMAIL PROTECTED] > Pager:704-354-6967 > > <> > > > > "MMS " made the following > annotations on 05/02/02 13:21:23 > > -- > This message is for the named person's use only. It may contain > confidential, proprietary, or legally privileged information. No > confidentiality or privilege is waived or lost by any mistransmission. If > you receive this message in error, please immediately delete it and all > copies of it from your system, destroy any hard copies of it, and notify the > sender. You must not, directly or indirectly, use, disclose, distribute, > print, or copy any part of this message if you are not the intended > recipient. Health First reserves the right to monitor all e-mail > communications through its networks. Any views or opinions expressed in > this message are solely those of the individual sender, except (1) where the > message states such views or opinions are on behalf of a particular entity; > and (2) the sender is authorized by the entity to give such views or > opinions. > > > ==
Re: Recovering SP node to Standalone RS6000
Bill, your colleague was correct, you can restore a non bootable mksysb tape using an install cd. As opposed to doing that, though, just backup your mksysb to a file on your CWS, and then use NIM to restore that mksysb onto your new node. It will handle the tough stuff for ya. You can also do a savevg for all non-rootvg vgs. Still doesn't get any raw devices though, like SysBack will. On Thu, 2002-05-02 at 12:40, Jolley, Bill wrote: > No, I do not have a tape drive attached to the SP node. I have introduced > AIX sysback as an alternative. Several colleagues stated that you could > boot from cdrom and use the image on tape as input and basically I am > restored. I disagreed. But thanks. Sysback appears to be much easier than > jumping through hoops. > > -Original Message- > From: David Longo [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 1:07 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > Do you have a tape drive physically attached to the SP node? > If so then you can do fairly easily. If not then I think you need > AIX Sysback to make a mksysb to a remote tape. You can't make > a mksysb image to disk and then copy that image to tape - it's > not a bootable image. > > David Longo > > >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> > Here is what I need to accomplish or would like to. Create a mksysb of the > SP Node, copy the image to media. At the recovery site, I will need to > restore this image to the standalone rs6000. I do not know if this is > possible even if I use the cloning process. > > > -Original Message- > From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 12:30 PM > To: [EMAIL PROTECTED] > Subject: Re: Recovering SP node to Standalone RS6000 > > > Connect to node and say shutdown -m > > > -Original Message- > From: Jolley, Bill [mailto:[EMAIL PROTECTED]] > Sent: Thursday, May 02, 2002 10:52 AM > To: [EMAIL PROTECTED] > Subject: Recovering SP node to Standalone RS6000 > > > I have a TSM server located on an IBM SP Node (winterhawk) and would like to > recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or > have suggestions? > > Thanks, > > Bill Jolley > EDS SS-SEMainframe Services > Telephone:704-548-5524 > Email:[EMAIL PROTECTED] > Pager:704-354-6967 > > <> > > > > "MMS " made the following > annotations on 05/02/02 13:21:23 > > -- > This message is for the named person's use only. It may contain > confidential, proprietary, or legally privileged information. No > confidentiality or privilege is waived or lost by any mistransmission. If > you receive this message in error, please immediately delete it and all > copies of it from your system, destroy any hard copies of it, and notify the > sender. You must not, directly or indirectly, use, disclose, distribute, > print, or copy any part of this message if you are not the intended > recipient. Health First reserves the right to monitor all e-mail > communications through its networks. Any views or opinions expressed in > this message are solely those of the individual sender, except (1) where the > message states such views or opinions are on behalf of a particular entity; > and (2) the sender is authorized by the entity to give such views or > opinions. > > > == signature.asc Description: This is a digitally signed message part
Re: Recovering SP node to Standalone RS6000
No, I do not have a tape drive attached to the SP node. I have introduced AIX sysback as an alternative. Several colleagues stated that you could boot from cdrom and use the image on tape as input and basically I am restored. I disagreed. But thanks. Sysback appears to be much easier than jumping through hoops. -Original Message- From: David Longo [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 1:07 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Do you have a tape drive physically attached to the SP node? If so then you can do fairly easily. If not then I think you need AIX Sysback to make a mksysb to a remote tape. You can't make a mksysb image to disk and then copy that image to tape - it's not a bootable image. David Longo >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> Here is what I need to accomplish or would like to. Create a mksysb of the SP Node, copy the image to media. At the recovery site, I will need to restore this image to the standalone rs6000. I do not know if this is possible even if I use the cloning process. -Original Message- From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 12:30 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Connect to node and say shutdown -m -Original Message- From: Jolley, Bill [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 10:52 AM To: [EMAIL PROTECTED] Subject: Recovering SP node to Standalone RS6000 I have a TSM server located on an IBM SP Node (winterhawk) and would like to recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or have suggestions? Thanks, Bill Jolley EDS SS-SEMainframe Services Telephone:704-548-5524 Email:[EMAIL PROTECTED] Pager:704-354-6967 <> "MMS " made the following annotations on 05/02/02 13:21:23 -- This message is for the named person's use only. It may contain confidential, proprietary, or legally privileged information. No confidentiality or privilege is waived or lost by any mistransmission. If you receive this message in error, please immediately delete it and all copies of it from your system, destroy any hard copies of it, and notify the sender. You must not, directly or indirectly, use, disclose, distribute, print, or copy any part of this message if you are not the intended recipient. Health First reserves the right to monitor all e-mail communications through its networks. Any views or opinions expressed in this message are solely those of the individual sender, except (1) where the message states such views or opinions are on behalf of a particular entity; and (2) the sender is authorized by the entity to give such views or opinions. ==
Re: Recovering SP node to Standalone RS6000
Do you have a tape drive physically attached to the SP node? If so then you can do fairly easily. If not then I think you need AIX Sysback to make a mksysb to a remote tape. You can't make a mksysb image to disk and then copy that image to tape - it's not a bootable image. David Longo >>> [EMAIL PROTECTED] 05/02/02 12:50PM >>> Here is what I need to accomplish or would like to. Create a mksysb of the SP Node, copy the image to media. At the recovery site, I will need to restore this image to the standalone rs6000. I do not know if this is possible even if I use the cloning process. -Original Message- From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 12:30 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Connect to node and say shutdown -m -Original Message- From: Jolley, Bill [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 10:52 AM To: [EMAIL PROTECTED] Subject: Recovering SP node to Standalone RS6000 I have a TSM server located on an IBM SP Node (winterhawk) and would like to recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or have suggestions? Thanks, Bill Jolley EDS SS-SEMainframe Services Telephone:704-548-5524 Email:[EMAIL PROTECTED] Pager:704-354-6967 <> "MMS " made the following annotations on 05/02/02 13:21:23 -- This message is for the named person's use only. It may contain confidential, proprietary, or legally privileged information. No confidentiality or privilege is waived or lost by any mistransmission. If you receive this message in error, please immediately delete it and all copies of it from your system, destroy any hard copies of it, and notify the sender. You must not, directly or indirectly, use, disclose, distribute, print, or copy any part of this message if you are not the intended recipient. Health First reserves the right to monitor all e-mail communications through its networks. Any views or opinions expressed in this message are solely those of the individual sender, except (1) where the message states such views or opinions are on behalf of a particular entity; and (2) the sender is authorized by the entity to give such views or opinions. ==
Re: Recovering SP node to Standalone RS6000
Here is what I need to accomplish or would like to. Create a mksysb of the SP Node, copy the image to media. At the recovery site, I will need to restore this image to the standalone rs6000. I do not know if this is possible even if I use the cloning process. -Original Message- From: PINNI, BALANAND (SBCSI) [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 12:30 PM To: [EMAIL PROTECTED] Subject: Re: Recovering SP node to Standalone RS6000 Connect to node and say shutdown -m -Original Message- From: Jolley, Bill [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 10:52 AM To: [EMAIL PROTECTED] Subject: Recovering SP node to Standalone RS6000 I have a TSM server located on an IBM SP Node (winterhawk) and would like to recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or have suggestions? Thanks, Bill Jolley EDS SS-SEMainframe Services Telephone:704-548-5524 Email:[EMAIL PROTECTED] Pager:704-354-6967 <>
Re: Recovering SP node to Standalone RS6000
Hot Diggety! Jolley, Bill was rumored to have written: > I have a TSM server located on an IBM SP Node (winterhawk) and would like to > recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or > have suggestions? Offhand, best bet is probably to do a mksysb backup (making sure that device drivers for both boxes exists, among other key gotchas) and then a mksysb install from that image. You can't just do a normal file backup and then restore because there are a bunch of system specific stuff such as the ODM entries, installed filesets, etc. Even more critical to get it right when SP and non-SP is concerned. I haven't personally done that with our SP and non-SP nodes as you describe, so that's about all I can suggest from what I've heard from others who has done similar things in the past. It's usually done as a way to recover from a total SP node system failure, rather than migrating to or from the SP, though. -Dan Foster IP Systems Engineering (IPSE) Global Crossing Telecommunications
Re: Recovering SP node to Standalone RS6000
Connect to node and say shutdown -m -Original Message- From: Jolley, Bill [mailto:[EMAIL PROTECTED]] Sent: Thursday, May 02, 2002 10:52 AM To: [EMAIL PROTECTED] Subject: Recovering SP node to Standalone RS6000 I have a TSM server located on an IBM SP Node (winterhawk) and would like to recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or have suggestions? Thanks, Bill Jolley EDS SS-SEMainframe Services Telephone:704-548-5524 Email:[EMAIL PROTECTED] Pager:704-354-6967 <>
Recovering SP node to Standalone RS6000
I have a TSM server located on an IBM SP Node (winterhawk) and would like to recover to a standalone RS/6000 (H80). Do anyone have/know of a procedure or have suggestions? Thanks, Bill Jolley EDS SS-SEMainframe Services Telephone:704-548-5524 Email:[EMAIL PROTECTED] Pager:704-354-6967 <> Jolley, Bill.vcf Description: Binary data