Re: [Bacula-users] LIP reset occurred (0), device removed.
Hi,
Seems that changing the Fibber do the trick. More that 30GB are copied
now to LT05 Tape without any troubles.
Regards, I
2013/8/20 Clark, Patricia A. clar...@ornl.gov
Possibly the fiber cable? Can you swap it out and try again?
I had 20 fiber connections and one of them needed replacing. It made the
drive look bad from the server, but the library did not report any error
conditions with the drive.
Patti Clark
Linux System Administrator
Research and Development Systems Support Oak Ridge National Laboratory
From: Iban Cabrillo cabri...@ifca.unican.esmailto:
cabri...@ifca.unican.es
Date: Tuesday, August 20, 2013 12:45 PM
To: Radosław Korzeniewski rados...@korzeniewski.netmailto:
rados...@korzeniewski.net
Cc: Bacula Users Bacula-users@lists.sourceforge.netmailto:
Bacula-users@lists.sourceforge.net
Subject: Re: [Bacula-users] LIP reset occurred (0), device removed.
Hi,
this is the qlogic driver version:
[1.348682] qla2xxx [:07:00.0]-00fa:1: QLogic Fibre Channed HBA
Driver: 8.03.07.12-k.
[1.348686] qla2xxx [:07:00.0]-00fb:1: QLogic QLE2562 - QLogic 8Gb
FC Dual-port HBA for System x.
[1.348699] qla2xxx [:07:00.0]-00fc:1: ISP2532: PCIe (2.5GT/s x8) @
:07:00.0 hdma+ host#=1 fw=5.06.05 (90d5).
[1.348768] qla2xxx [:07:00.1]-001d: : Found an ISP2532 irq 19
iobase 0xc9c68000.
[1.348949] qla2xxx :07:00.1: irq 44 for MSI/MSI-X
[1.348956] qla2xxx :07:00.1: irq 45 for MSI/MSI-X
[1.349023] qla2xxx [:07:00.1]-0040:2: Configuring PCI space...
[1.349028] qla2xxx :07:00.1: setting latency timer to 64
[1.361424] qla2xxx [:07:00.1]-0061:2: Configure NVRAM parameters...
[1.369088] qla2xxx [:07:00.1]-0078:2: Verifying loaded RISC code...
[1.369131] qla2xxx [:07:00.1]-0092:2: Loading via request-firmware.
[1.400994] qla2xxx [:07:00.1]-00c0:2: Allocate (64 KB) for FCE...
[1.401064] qla2xxx [:07:00.1]-00c3:2: Allocated (64 KB) EFT ...
[1.401150] qla2xxx [:07:00.1]-00c5:2: Allocated (1350 KB) for
firmware dump.
[1.405503] scsi2 : qla2xxx
[1.405763] qla2xxx [:07:00.1]-00fa:2: QLogic Fibre Channed HBA
Driver: 8.03.07.12-k.
[1.405767] qla2xxx [:07:00.1]-00fb:2: QLogic QLE2562 - QLogic 8Gb
FC Dual-port HBA for System x.
[1.405779] qla2xxx [:07:00.1]-00fc:2: ISP2532: PCIe (2.5GT/s x8) @
:07:00.1 hdma+ host#=2 fw=5.06.05 (90d5).
..
[2.928979] scsi 1:0:0:0: Sequential-Access IBM ULT3580-TD3
93GP PQ: 0 ANSI: 3
[2.935530] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[2.935861] st 1:0:0:0: Attached scsi tape st0
[2.935864] st 1:0:0:0: st0: try direct i/o: yes (alignment 4 B)
[3.939166] qla2xxx [:07:00.1]-500a:2: LOOP UP detected (8 Gbps).
[3.997944] scsi 2:0:0:0: Sequential-Access IBM ULT3580-TD5
C7RC PQ: 0 ANSI: 6
[4.000531] scsi 2:0:0:1: Medium ChangerIBM 03584L32
B570 PQ: 0 ANSI: 6
[4.012583] st 2:0:0:0: Attached scsi tape st1
[4.012586] st 2:0:0:0: st1: try direct i/o: yes (alignment 4 B)
[4.013947] osst :I: Tape driver with OnStream support version 0.99.4
[4.013948] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[4.014691] SCSI Media Changer driver v0.25
[4.016286] ch0: type #1 (mt): 0x1+2 [medium transport]
[4.016289] ch0: type #2 (st): 0x401+1601 [storage]
[4.016291] ch0: type #3 (ie): 0x301+10 [import/export]
[4.016293] ch0: type #4 (dt): 0x101+2 [data transfer]
[1:0:0:0]tapeIBM ULT3580-TD3 93GP /dev/st0
[2:0:0:0]tapeIBM ULT3580-TD5 C7RC /dev/st1
[2:0:0:1]mediumx IBM 03584L32 B570 /dev/sch0
Some times the reset hapends whwn a few MBs are written others after a
couple of hundred MBs but only when we use the LTO5 ([2:0:0:0]tape
IBM ULT3580-TD5 C7RC /dev/st1 ) the LT03 always works grate.
the linux kernel running is :
Linux bacula 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux
and the bacula-sd configuration for LT05 tape:
Device {
# The TSM3100's second t3pe drive
Name = ULT3580-TD5
Archive Device = /dev/nst1
Device Type = Tape
Media Type = LTO-5
Autochanger = Yes
# Changer Device = inherited from Changer
Alert Command = sh -c '/usr/sbin/tapeinfo -f /dev/sg1 | /bin/sed -n
/TapeAlert/p
Drive Index = 0
RemovableMedia = yes
Random Access = no
Maximum Block Size = 262144
Maximum Network Buffer Size = 262144
Maximum Spool Size = 20gb
Maximum Job Spool Size = 10gb
Spool Directory = /backup/spool
AutomaticMount = Yes;
}
root@bacula:~# /usr/sbin/tapeinfo -f /dev/sg1
Product Type: Tape Drive
Vendor ID: 'IBM '
Product ID: 'ULT3580-TD5 '
Revision: 'C7RC'
Attached Changer API: No
SerialNumber: '00078ABB4C'
MinBlock: 1
MaxBlock: 8388608
SCSI ID: 0
SCSI LUN: 0
Ready: yes
BufferedMode: yes
Medium Type: 0x58
Density Code: 0x58
Re: [Bacula-users] LIP reset occurred (0), device removed.
Hi,
this is the qlogic driver version:
[1.348682] qla2xxx [:07:00.0]-00fa:1: QLogic Fibre Channed HBA
Driver: 8.03.07.12-k.
[1.348686] qla2xxx [:07:00.0]-00fb:1: QLogic QLE2562 - QLogic 8Gb
FC Dual-port HBA for System x.
[1.348699] qla2xxx [:07:00.0]-00fc:1: ISP2532: PCIe (2.5GT/s x8) @
:07:00.0 hdma+ host#=1 fw=5.06.05 (90d5).
[1.348768] qla2xxx [:07:00.1]-001d: : Found an ISP2532 irq 19
iobase 0xc9c68000.
[1.348949] qla2xxx :07:00.1: irq 44 for MSI/MSI-X
[1.348956] qla2xxx :07:00.1: irq 45 for MSI/MSI-X
[1.349023] qla2xxx [:07:00.1]-0040:2: Configuring PCI space...
[1.349028] qla2xxx :07:00.1: setting latency timer to 64
[1.361424] qla2xxx [:07:00.1]-0061:2: Configure NVRAM parameters...
[1.369088] qla2xxx [:07:00.1]-0078:2: Verifying loaded RISC code...
[1.369131] qla2xxx [:07:00.1]-0092:2: Loading via request-firmware.
[1.400994] qla2xxx [:07:00.1]-00c0:2: Allocate (64 KB) for FCE...
[1.401064] qla2xxx [:07:00.1]-00c3:2: Allocated (64 KB) EFT ...
[1.401150] qla2xxx [:07:00.1]-00c5:2: Allocated (1350 KB) for
firmware dump.
[1.405503] scsi2 : qla2xxx
[1.405763] qla2xxx [:07:00.1]-00fa:2: QLogic Fibre Channed HBA
Driver: 8.03.07.12-k.
[1.405767] qla2xxx [:07:00.1]-00fb:2: QLogic QLE2562 - QLogic 8Gb
FC Dual-port HBA for System x.
[1.405779] qla2xxx [:07:00.1]-00fc:2: ISP2532: PCIe (2.5GT/s x8) @
:07:00.1 hdma+ host#=2 fw=5.06.05 (90d5).
..
[2.928979] scsi 1:0:0:0: Sequential-Access IBM ULT3580-TD3
93GP PQ: 0 ANSI: 3
[2.935530] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[2.935861] st 1:0:0:0: Attached scsi tape st0
[2.935864] st 1:0:0:0: st0: try direct i/o: yes (alignment 4 B)
[3.939166] qla2xxx [:07:00.1]-500a:2: LOOP UP detected (8 Gbps).
[3.997944] scsi 2:0:0:0: Sequential-Access IBM ULT3580-TD5
C7RC PQ: 0 ANSI: 6
[4.000531] scsi 2:0:0:1: Medium ChangerIBM 03584L32
B570 PQ: 0 ANSI: 6
[4.012583] st 2:0:0:0: Attached scsi tape st1
[4.012586] st 2:0:0:0: st1: try direct i/o: yes (alignment 4 B)
[4.013947] osst :I: Tape driver with OnStream support version 0.99.4
[4.013948] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[4.014691] SCSI Media Changer driver v0.25
[4.016286] ch0: type #1 (mt): 0x1+2 [medium transport]
[4.016289] ch0: type #2 (st): 0x401+1601 [storage]
[4.016291] ch0: type #3 (ie): 0x301+10 [import/export]
[4.016293] ch0: type #4 (dt): 0x101+2 [data transfer]
[1:0:0:0]tapeIBM ULT3580-TD3 93GP /dev/st0
[2:0:0:0]tapeIBM ULT3580-TD5 C7RC /dev/st1
[2:0:0:1]mediumx IBM 03584L32 B570 /dev/sch0
Some times the reset hapends whwn a few MBs are written others after a
couple of hundred MBs but only when we use the LTO5 ([2:0:0:0]tape
IBM ULT3580-TD5 C7RC /dev/st1 ) the LT03 always works grate.
the linux kernel running is :
Linux bacula 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux
and the bacula-sd configuration for LT05 tape:
Device {
# The TSM3100's second t3pe drive
Name = ULT3580-TD5
Archive Device = /dev/nst1
Device Type = Tape
Media Type = LTO-5
Autochanger = Yes
# Changer Device = inherited from Changer
Alert Command = sh -c '/usr/sbin/tapeinfo -f /dev/sg1 | /bin/sed -n
/TapeAlert/p
Drive Index = 0
RemovableMedia = yes
Random Access = no
Maximum Block Size = 262144
Maximum Network Buffer Size = 262144
Maximum Spool Size = 20gb
Maximum Job Spool Size = 10gb
Spool Directory = /backup/spool
AutomaticMount = Yes;
}
root@bacula:~# /usr/sbin/tapeinfo -f /dev/sg1
Product Type: Tape Drive
Vendor ID: 'IBM '
Product ID: 'ULT3580-TD5 '
Revision: 'C7RC'
Attached Changer API: No
SerialNumber: '00078ABB4C'
MinBlock: 1
MaxBlock: 8388608
SCSI ID: 0
SCSI LUN: 0
Ready: yes
BufferedMode: yes
Medium Type: 0x58
Density Code: 0x58
BlockSize: 0
DataCompEnabled: yes
DataCompCapable: yes
DataDeCompEnabled: yes
CompType: 0x1
DeCompType: 0x1
Block Position: 582
Partition 0 Remaining Kbytes: -1
Partition 0 Size in Kbytes: -1
ActivePartition: 0
EarlyWarningSize: 0
NumPartitions: 0
MaxPartitions: 1
I appreciate any help. thanks in advance I.
2013/8/19 Radosław Korzeniewski rados...@korzeniewski.net
Hello,
2013/8/19 Iban Cabrillo cabri...@ifca.unican.es
Hi, Any Idea?
Seems something related to bacula, I have tried chaging the FC port,
but the result has been the same
FC LIP reset is not related to Bacula - IMHO. I had the same problem but
with a changer device. The problem was a second server which accidentally
accessed the same target (at random time). When I switch off the second
server the problem was cured. Sure, your problem could has a different
origin then my, and YMMV. BTW, what kernel tape driver do you use (Linux
stock)?
best regards
--
Radosław Korzeniewski
rados...@korzeniewski.net
--
Re: [Bacula-users] LIP reset occurred (0), device removed.
Possibly the fiber cable? Can you swap it out and try again?
I had 20 fiber connections and one of them needed replacing. It made the drive
look bad from the server, but the library did not report any error conditions
with the drive.
Patti Clark
Linux System Administrator
Research and Development Systems Support Oak Ridge National Laboratory
From: Iban Cabrillo cabri...@ifca.unican.esmailto:cabri...@ifca.unican.es
Date: Tuesday, August 20, 2013 12:45 PM
To: Radosław Korzeniewski
rados...@korzeniewski.netmailto:rados...@korzeniewski.net
Cc: Bacula Users
Bacula-users@lists.sourceforge.netmailto:Bacula-users@lists.sourceforge.net
Subject: Re: [Bacula-users] LIP reset occurred (0), device removed.
Hi,
this is the qlogic driver version:
[1.348682] qla2xxx [:07:00.0]-00fa:1: QLogic Fibre Channed HBA
Driver: 8.03.07.12-k.
[1.348686] qla2xxx [:07:00.0]-00fb:1: QLogic QLE2562 - QLogic 8Gb FC
Dual-port HBA for System x.
[1.348699] qla2xxx [:07:00.0]-00fc:1: ISP2532: PCIe (2.5GT/s x8) @
:07:00.0 hdma+ host#=1 fw=5.06.05 (90d5).
[1.348768] qla2xxx [:07:00.1]-001d: : Found an ISP2532 irq 19 iobase
0xc9c68000.
[1.348949] qla2xxx :07:00.1: irq 44 for MSI/MSI-X
[1.348956] qla2xxx :07:00.1: irq 45 for MSI/MSI-X
[1.349023] qla2xxx [:07:00.1]-0040:2: Configuring PCI space...
[1.349028] qla2xxx :07:00.1: setting latency timer to 64
[1.361424] qla2xxx [:07:00.1]-0061:2: Configure NVRAM parameters...
[1.369088] qla2xxx [:07:00.1]-0078:2: Verifying loaded RISC code...
[1.369131] qla2xxx [:07:00.1]-0092:2: Loading via request-firmware.
[1.400994] qla2xxx [:07:00.1]-00c0:2: Allocate (64 KB) for FCE...
[1.401064] qla2xxx [:07:00.1]-00c3:2: Allocated (64 KB) EFT ...
[1.401150] qla2xxx [:07:00.1]-00c5:2: Allocated (1350 KB) for firmware
dump.
[1.405503] scsi2 : qla2xxx
[1.405763] qla2xxx [:07:00.1]-00fa:2: QLogic Fibre Channed HBA Driver:
8.03.07.12-k.
[1.405767] qla2xxx [:07:00.1]-00fb:2: QLogic QLE2562 - QLogic 8Gb FC
Dual-port HBA for System x.
[1.405779] qla2xxx [:07:00.1]-00fc:2: ISP2532: PCIe (2.5GT/s x8) @
:07:00.1 hdma+ host#=2 fw=5.06.05 (90d5).
..
[2.928979] scsi 1:0:0:0: Sequential-Access IBM ULT3580-TD3 93GP
PQ: 0 ANSI: 3
[2.935530] st: Version 20101219, fixed bufsize 32768, s/g segs 256
[2.935861] st 1:0:0:0: Attached scsi tape st0
[2.935864] st 1:0:0:0: st0: try direct i/o: yes (alignment 4 B)
[3.939166] qla2xxx [:07:00.1]-500a:2: LOOP UP detected (8 Gbps).
[3.997944] scsi 2:0:0:0: Sequential-Access IBM ULT3580-TD5 C7RC
PQ: 0 ANSI: 6
[4.000531] scsi 2:0:0:1: Medium ChangerIBM 03584L32 B570
PQ: 0 ANSI: 6
[4.012583] st 2:0:0:0: Attached scsi tape st1
[4.012586] st 2:0:0:0: st1: try direct i/o: yes (alignment 4 B)
[4.013947] osst :I: Tape driver with OnStream support version 0.99.4
[4.013948] osst :I: $Id: osst.c,v 1.73 2005/01/01 21:13:34 wriede Exp $
[4.014691] SCSI Media Changer driver v0.25
[4.016286] ch0: type #1 (mt): 0x1+2 [medium transport]
[4.016289] ch0: type #2 (st): 0x401+1601 [storage]
[4.016291] ch0: type #3 (ie): 0x301+10 [import/export]
[4.016293] ch0: type #4 (dt): 0x101+2 [data transfer]
[1:0:0:0]tapeIBM ULT3580-TD3 93GP /dev/st0
[2:0:0:0]tapeIBM ULT3580-TD5 C7RC /dev/st1
[2:0:0:1]mediumx IBM 03584L32 B570 /dev/sch0
Some times the reset hapends whwn a few MBs are written others after a couple
of hundred MBs but only when we use the LTO5 ([2:0:0:0]tapeIBM
ULT3580-TD5 C7RC /dev/st1 ) the LT03 always works grate.
the linux kernel running is :
Linux bacula 3.2.0-4-amd64 #1 SMP Debian 3.2.46-1 x86_64 GNU/Linux
and the bacula-sd configuration for LT05 tape:
Device {
# The TSM3100's second t3pe drive
Name = ULT3580-TD5
Archive Device = /dev/nst1
Device Type = Tape
Media Type = LTO-5
Autochanger = Yes
# Changer Device = inherited from Changer
Alert Command = sh -c '/usr/sbin/tapeinfo -f /dev/sg1 | /bin/sed -n
/TapeAlert/p
Drive Index = 0
RemovableMedia = yes
Random Access = no
Maximum Block Size = 262144
Maximum Network Buffer Size = 262144
Maximum Spool Size = 20gb
Maximum Job Spool Size = 10gb
Spool Directory = /backup/spool
AutomaticMount = Yes;
}
root@bacula:~# /usr/sbin/tapeinfo -f /dev/sg1
Product Type: Tape Drive
Vendor ID: 'IBM '
Product ID: 'ULT3580-TD5 '
Revision: 'C7RC'
Attached Changer API: No
SerialNumber: '00078ABB4C'
MinBlock: 1
MaxBlock: 8388608
SCSI ID: 0
SCSI LUN: 0
Ready: yes
BufferedMode: yes
Medium Type: 0x58
Density Code: 0x58
BlockSize: 0
DataCompEnabled: yes
DataCompCapable: yes
DataDeCompEnabled: yes
CompType: 0x1
DeCompType: 0x1
Block Position: 582
Partition 0 Remaining Kbytes: -1
Partition 0 Size in Kbytes: -1
ActivePartition: 0
EarlyWarningSize: 0
NumPartitions: 0
Re: [Bacula-users] LIP reset occurred (0), device removed.
Hi, Any Idea? Seems something related to bacula, I have tried chaging the FC port, but the result has been the same Regards, I 2013/8/16 Iban Cabrillo cabri...@ifca.unican.es Dear, From time to now, I can use the LTO5 drive. We are using a debian bacula installation: @bacula:~# dpkg -l | grep bacula ii bacula 5.2.6+dfsg-9 all network backup service - metapackage ii bacula-client 5.2.6+dfsg-9all network backup service - client metapackage ii bacula-common5.2.6+dfsg-9amd64network backup service - common support files ii bacula-common-mysql 5.2.6+dfsg-9 amd64network backup service - MySQL common files ii bacula-console 5.2.6+dfsg-9 amd64network backup service - text console ii bacula-console-qt 5.2.6+dfsg-9 amd64network backup service - Bacula Administration Tool ii bacula-director-common 5.2.6+dfsg-9 amd64network backup service - Director common files ii bacula-director-mysql 5.2.6+dfsg-9 amd64network backup service - MySQL storage for Director ii bacula-fd 5.2.6+dfsg-9 amd64network backup service - file daemon ii bacula-sd 5.2.6+dfsg-9 amd64network backup service - storage daemon ii bacula-sd-mysql 5.2.6+dfsg-9 amd64network backup service - MySQL SD tools ii bacula-server 5.2.6+dfsg-9 all network backup service - server metapackage ii bacula-traymonitor 5.2.6+dfsg-9 amd64network backup service - tray monitor The Robot storage systems is formed by 2 tapes (LT03 FC connection 2Gbps and LT05 8Gbps FC connection) and and autochanger.: root@bacula:~# lsscsi [1:0:0:0]tapeIBM ULT3580-TD3 93GP /dev/st0 [4:0:0:0]tapeIBM ULT3580-TD5 C7RC /dev/st1 [4:0:0:1]mediumx IBM 03584L32 B570 /dev/sch0 Is has been working fine from several months but now every time i try to access to LT05 a FC lip reset happens, this is not immediately (the tapes begins to write data, I have used spool data and no spool data with the same result), but after a few minutes : Aug 16 11:40:57 bacula kernel: [168140.448017] rport-4:0-0: blocked FC remote port time out: removing target and saving binding Aug 16 11:40:57 bacula kernel: [168140.660577] st1: Error 1 (driver bt 0x0, host bt 0x1). Aug 16 11:40:57 bacula kernel: [168140.660624] st1: Error 1 (driver bt 0x0, host bt 0x1). Aug 16 11:40:57 bacula kernel: [168140.660644] st1: Error 1 (driver bt 0x0, host bt 0x1). Aug 16 11:40:57 bacula kernel: [168140.661988] st1: Error 1 (driver bt 0x0, host bt 0x1). then the LT05 and autochanger device disappear from my devices and i have to lip/scan again, but all the jobs that was running or scheduled fail The LT03 works grate if i do not use the LT05 of course. I have changed the FC card ith the same result, check the tape drive using the mt commands and works fine too Any one has seen something similar?? Regards, Bertrand Russell: *El problema con el mundo es que los estúpidos están seguros de todo y los inteligentes están llenos de dudas* -- Iban Cabrillo Bartolome Instituto de Fisica de Cantabria (IFCA) Santander, Spain Tel: +34942200969 Bertrand Russell: *El problema con el mundo es que los estúpidos están seguros de todo y los inteligentes están llenos de dudas* -- Get 100% visibility into Java/.NET code with AppDynamics Lite! It's a free troubleshooting tool designed for production. Get down to code-level detail for bottlenecks, with 2% overhead. Download for free and get started troubleshooting in minutes. http://pubads.g.doubleclick.net/gampad/clk?id=48897031iu=/4140/ostg.clktrk___ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
Re: [Bacula-users] LIP reset occurred (0), device removed.
Hello, 2013/8/19 Iban Cabrillo cabri...@ifca.unican.es Hi, Any Idea? Seems something related to bacula, I have tried chaging the FC port, but the result has been the same FC LIP reset is not related to Bacula - IMHO. I had the same problem but with a changer device. The problem was a second server which accidentally accessed the same target (at random time). When I switch off the second server the problem was cured. Sure, your problem could has a different origin then my, and YMMV. BTW, what kernel tape driver do you use (Linux stock)? best regards -- Radosław Korzeniewski rados...@korzeniewski.net -- Introducing Performance Central, a new site from SourceForge and AppDynamics. Performance Central is your source for news, insights, analysis and resources for efficient Application Performance Management. Visit us today! http://pubads.g.doubleclick.net/gampad/clk?id=48897511iu=/4140/ostg.clktrk___ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
[Bacula-users] LIP reset occurred (0), device removed.
Dear, From time to now, I can use the LTO5 drive. We are using a debian bacula installation: @bacula:~# dpkg -l | grep bacula ii bacula 5.2.6+dfsg-9 all network backup service - metapackage ii bacula-client 5.2.6+dfsg-9all network backup service - client metapackage ii bacula-common5.2.6+dfsg-9amd64network backup service - common support files ii bacula-common-mysql 5.2.6+dfsg-9 amd64network backup service - MySQL common files ii bacula-console 5.2.6+dfsg-9 amd64network backup service - text console ii bacula-console-qt 5.2.6+dfsg-9 amd64network backup service - Bacula Administration Tool ii bacula-director-common 5.2.6+dfsg-9 amd64network backup service - Director common files ii bacula-director-mysql 5.2.6+dfsg-9 amd64network backup service - MySQL storage for Director ii bacula-fd 5.2.6+dfsg-9 amd64network backup service - file daemon ii bacula-sd 5.2.6+dfsg-9 amd64network backup service - storage daemon ii bacula-sd-mysql 5.2.6+dfsg-9 amd64network backup service - MySQL SD tools ii bacula-server 5.2.6+dfsg-9 all network backup service - server metapackage ii bacula-traymonitor 5.2.6+dfsg-9 amd64network backup service - tray monitor The Robot storage systems is formed by 2 tapes (LT03 FC connection 2Gbps and LT05 8Gbps FC connection) and and autochanger.: root@bacula:~# lsscsi [1:0:0:0]tapeIBM ULT3580-TD3 93GP /dev/st0 [4:0:0:0]tapeIBM ULT3580-TD5 C7RC /dev/st1 [4:0:0:1]mediumx IBM 03584L32 B570 /dev/sch0 Is has been working fine from several months but now every time i try to access to LT05 a FC lip reset happens, this is not immediately (the tapes begins to write data, I have used spool data and no spool data with the same result), but after a few minutes : Aug 16 11:40:57 bacula kernel: [168140.448017] rport-4:0-0: blocked FC remote port time out: removing target and saving binding Aug 16 11:40:57 bacula kernel: [168140.660577] st1: Error 1 (driver bt 0x0, host bt 0x1). Aug 16 11:40:57 bacula kernel: [168140.660624] st1: Error 1 (driver bt 0x0, host bt 0x1). Aug 16 11:40:57 bacula kernel: [168140.660644] st1: Error 1 (driver bt 0x0, host bt 0x1). Aug 16 11:40:57 bacula kernel: [168140.661988] st1: Error 1 (driver bt 0x0, host bt 0x1). then the LT05 and autochanger device disappear from my devices and i have to lip/scan again, but all the jobs that was running or scheduled fail The LT03 works grate if i do not use the LT05 of course. I have changed the FC card ith the same result, check the tape drive using the mt commands and works fine too Any one has seen something similar?? Regards, Bertrand Russell: *El problema con el mundo es que los estúpidos están seguros de todo y los inteligentes están llenos de dudas* -- Get 100% visibility into Java/.NET code with AppDynamics Lite! It's a free troubleshooting tool designed for production. Get down to code-level detail for bottlenecks, with 2% overhead. Download for free and get started troubleshooting in minutes. http://pubads.g.doubleclick.net/gampad/clk?id=48897031iu=/4140/ostg.clktrk___ Bacula-users mailing list Bacula-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/bacula-users
