Re: [OSL | CCIE_Voice] CUCM GK Port Number
Marty Sorry to beat a dead horse but I actually think its easier that that. The gatekeeper signaling port from the CUCM should be in that ephemeral range on the left and right side of the show command by default (as shown). Really, I think all the question is asking is to configure the gatekeeper such that the CUCMs both show with the listed name as well as the other gateway. You are correct in that the question is listed incorrectly. The ephemeral ports should be x or something. IPExpert is actually pretty good with the proof reading of their questions compared to others I've seen. It is aggravating when you have to take the time to figure out an incorrect question though! :) Josh On Jun 13, 2013 11:56 PM, Martin Sloan martinsloa...@gmail.com wrote: Thanks, Josh. I was getting caught up because the signaling ports in the output provided in the task were in the ephemeral range but the task said that port matching was a requirement. Based on the feedback here, I think the screen shot in the task was not right and was supposed to show the ports as 1720. If that was the case, I'd update the service parameter for the gk trunk, but It seems I can't force a match on the ports that were provided in the task. Thanks all for the help. Marty On Thursday, June 13, 2013, Josh Petro wrote: Hi Marty Bill and Justin are correct in that you can change the port number in the CUCM and the Gateway to reflect the signaling port (first port) The RAS port (second port listed on the line) will be in the ephemeral range. The ephemeral port range can't be changed on the CUCM as far as I know. I also remember Vic talking about that in a VOD in volume 1 (its in the 4.6 gatekeeper section). Josh On Jun 13, 2013 7:25 PM, Bill Lake whl...@gmail.com wrote: Marty, You got to the first column and select System parameters then scroll Dow the the H323 section and there will be your 1720 and there you will put the name of the gk trunk setup in your trunk config Reset the trunk and it should start using 1720 Sent from my iPhone On Jun 13, 2013, at 4:11 PM, Martin Sloan martinsloa...@gmail.com wrote: Justin, Thanks for the assist! I'm still lost on the requirement for this task b/c based on the output supplied, the CUCM's register with GK using ports 40446 and 35246 (gk-trunk_1 and gk-trunk_2). I'm not sure if: 1) I'm misunderstanding the question and/or output 2) The output in the task was supposed to show the CUCM's registered with port 1720 3) There is really a way to register the CUCM's with the ports they have in the output and I don't know how to do it. I've attached a SS of the section. Can you make any suggestions? I'm leaning heavily towards option 1 :-\ Thanks, Marty On Thu, Jun 13, 2013 at 4:04 PM, Justin McIntyre justin.mcint...@blackbox.com wrote: With regards to your service parameter. Just make sure that the name of your trunk is listed in this service parameter. Then re-register your UCMs to the Gatekeeper. Couldn't also hurt to shut / no shut the gatekeeper. The service parameter is the key to what you are looking for here. Depending on what time frames you have entered for your registration timeouts you should see it repair after some time as long as you have the service parameter configured correctly. Thanks, Justin This email and any files transmitted with it are confidential and are intended for the sole use of the individual to whom they are addressed. Black Box Corporation reserves the right to scan all e-mail traffic for restricted content and to monitor all e-mail in general. If you are not the intended recipient or you have received this email in error, any use, dissemination or forwarding of this email is strictly prohibited. If you have received this email in error, please notify the sender by replying to this email. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com Vol2_Lab6_Task4.2.png ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] ip pblue multilab version..
Hello guys.. i have multi lab version and try to sue with cucm I want to know how can register multiple ip blue.. I have 4 loop back adapter but all showing same mac address so how can i will use for register separate phone for this ip blue? can some one help me? -- Thanks Regard's Amit Sharma ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Pre-config
Hello can you send me Pre-config (HQ,Br1,Br2,sw,Pstn,Fr) for ccoi-voicelab cordially jlailia imed Voip Administrator gsm:0021696819671 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUCM GK Port Number
Hey Josh, No worries, it's great to get feedback on this. I agree with you as well. It has to be either a mis-wording of the task requirement or an error in presenting the gatekeeper endpoint data. I also think the IPExpert material has been stellar, which made me really cautious to call it an error in the material without getting some expert feedback. I didn't think there was a way to hard code the ports outside of the service parameters but I wanted to check first. Marty On Fri, Jun 14, 2013 at 6:22 AM, Josh Petro josh.pe...@gmail.com wrote: Marty Sorry to beat a dead horse but I actually think its easier that that. The gatekeeper signaling port from the CUCM should be in that ephemeral range on the left and right side of the show command by default (as shown). Really, I think all the question is asking is to configure the gatekeeper such that the CUCMs both show with the listed name as well as the other gateway. You are correct in that the question is listed incorrectly. The ephemeral ports should be x or something. IPExpert is actually pretty good with the proof reading of their questions compared to others I've seen. It is aggravating when you have to take the time to figure out an incorrect question though! :) Josh On Jun 13, 2013 11:56 PM, Martin Sloan martinsloa...@gmail.com wrote: Thanks, Josh. I was getting caught up because the signaling ports in the output provided in the task were in the ephemeral range but the task said that port matching was a requirement. Based on the feedback here, I think the screen shot in the task was not right and was supposed to show the ports as 1720. If that was the case, I'd update the service parameter for the gk trunk, but It seems I can't force a match on the ports that were provided in the task. Thanks all for the help. Marty On Thursday, June 13, 2013, Josh Petro wrote: Hi Marty Bill and Justin are correct in that you can change the port number in the CUCM and the Gateway to reflect the signaling port (first port) The RAS port (second port listed on the line) will be in the ephemeral range. The ephemeral port range can't be changed on the CUCM as far as I know. I also remember Vic talking about that in a VOD in volume 1 (its in the 4.6 gatekeeper section). Josh On Jun 13, 2013 7:25 PM, Bill Lake whl...@gmail.com wrote: Marty, You got to the first column and select System parameters then scroll Dow the the H323 section and there will be your 1720 and there you will put the name of the gk trunk setup in your trunk config Reset the trunk and it should start using 1720 Sent from my iPhone On Jun 13, 2013, at 4:11 PM, Martin Sloan martinsloa...@gmail.com wrote: Justin, Thanks for the assist! I'm still lost on the requirement for this task b/c based on the output supplied, the CUCM's register with GK using ports 40446 and 35246 (gk-trunk_1 and gk-trunk_2). I'm not sure if: 1) I'm misunderstanding the question and/or output 2) The output in the task was supposed to show the CUCM's registered with port 1720 3) There is really a way to register the CUCM's with the ports they have in the output and I don't know how to do it. I've attached a SS of the section. Can you make any suggestions? I'm leaning heavily towards option 1 :-\ Thanks, Marty On Thu, Jun 13, 2013 at 4:04 PM, Justin McIntyre justin.mcint...@blackbox.com wrote: With regards to your service parameter. Just make sure that the name of your trunk is listed in this service parameter. Then re-register your UCMs to the Gatekeeper. Couldn't also hurt to shut / no shut the gatekeeper. The service parameter is the key to what you are looking for here. Depending on what time frames you have entered for your registration timeouts you should see it repair after some time as long as you have the service parameter configured correctly. Thanks, Justin This email and any files transmitted with it are confidential and are intended for the sole use of the individual to whom they are addressed. Black Box Corporation reserves the right to scan all e-mail traffic for restricted content and to monitor all e-mail in general. If you are not the intended recipient or you have received this email in error, any use, dissemination or forwarding of this email is strictly prohibited. If you have received this email in error, please notify the sender by replying to this email. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com Vol2_Lab6_Task4.2.png ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For
[OSL | CCIE_Voice] sip trunk
Hi please tell what parametres are required to integtate CUCM and siemens sip trunk.. we have already configured sip trunk on both sides but one way calling is there from CUCM we are not able to call seimens extension how can we trace trunk logs on rtmt please help if u can -- Regards, Dharambir Kumar ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] ip pblue multilab version..
You have to manually change the MAC addresses on the loopback adapters you created, I think the first one create ends with 50, so I tend to change it to 51, 52, 53, ... as needed. Bill On 6/14/13, Amit Sharma aryan231...@gmail.com wrote: Hello guys.. i have multi lab version and try to sue with cucm I want to know how can register multiple ip blue.. I have 4 loop back adapter but all showing same mac address so how can i will use for register separate phone for this ip blue? can some one help me? -- Thanks Regard's Amit Sharma ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] BLUE Screen on SC Phones.
Mike and others, thanks lot, now the blue screen phone works. i haven't try to put back to default background. When i power up next morning, it just work and poick up the DN from UCM. Mistery to me. K From: michael.se...@compucom.com michael.se...@compucom.com To: karen.johnson...@yahoo.ca; ccie_voice@onlinestudylist.com Sent: Thursday, June 13, 2013 10:18:50 AM Subject: RE: BLUE Screen on SC Phones. Karen, I really can’t explain it, technically I can’t explain why this happens. My screens on SC phones turned bright blue with no information and the phones were registered. Finally, in desperation I tried changing the phones back to the default background image and it worked. I also put other background images on the phones and it worked also. Good Luck. Michael Sears, CCIE(V)#38404 Cisco Certified Unfied Communications Computing Systems Specialist E911 Infrastructure Specialist “Designing and Implementing Cisco Unified Communications on Unified Computing Systems” From:Karen Johnson [mailto:karen.johnson...@yahoo.ca] Sent: Thursday, June 13, 2013 10:13 AM To: Sears, Michael (msears); ccie_voice@onlinestudylist.com Subject: Re: BLUE Screen on SC Phones. ah will test that in moment and update you. but why is that ? From:michael.se...@compucom.com michael.se...@compucom.com To: ccie_voice@onlinestudylist.com Cc: karen.johnson...@yahoo.ca Sent: Wednesday, June 12, 2013 7:24:54 PM Subject: BLUE Screen on SC Phones. Karen, I experienced the same thing when studying for the IE in my home lab. The solution for me to get rid of the very blue screen was to check the background image and revert to the standard image. Then my phones showed showed correct information. Michael Sears, CCIE(V)#38404 Cisco Certified Unfied Communications Computing Systems Specialist E911 Insrastructure Specialist Compucom Systems Western Region___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] BLUE Screen on SC Phones.
Didn’t fully read trail…is this a hardware vpn setup? From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Karen Johnson Sent: Friday, June 14, 2013 1:03 PM To: michael.se...@compucom.com; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] BLUE Screen on SC Phones. Mike and others, thanks lot, now the blue screen phone works. i haven't try to put back to default background. When i power up next morning, it just work and poick up the DN from UCM. Mistery to me. K From: michael.se...@compucom.commailto:michael.se...@compucom.com michael.se...@compucom.commailto:michael.se...@compucom.com To: karen.johnson...@yahoo.camailto:karen.johnson...@yahoo.ca; ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com Sent: Thursday, June 13, 2013 10:18:50 AM Subject: RE: BLUE Screen on SC Phones. Karen, I really can’t explain it, technically I can’t explain why this happens. My screens on SC phones turned bright blue with no information and the phones were registered. Finally, in desperation I tried changing the phones back to the default background image and it worked. I also put other background images on the phones and it worked also. Good Luck. Michael Sears, CCIE(V)#38404 Cisco Certified Unfied Communications Computing Systems Specialist E911 Infrastructure Specialist “Designing and Implementing Cisco Unified Communications on Unified Computing Systems” From: Karen Johnson [mailto:karen.johnson...@yahoo.ca] Sent: Thursday, June 13, 2013 10:13 AM To: Sears, Michael (msears); ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com Subject: Re: BLUE Screen on SC Phones. ah will test that in moment and update you. but why is that ? From: michael.se...@compucom.commailto:michael.se...@compucom.com michael.se...@compucom.commailto:michael.se...@compucom.com To: ccie_voice@onlinestudylist.commailto:ccie_voice@onlinestudylist.com Cc: karen.johnson...@yahoo.camailto:karen.johnson...@yahoo.ca Sent: Wednesday, June 12, 2013 7:24:54 PM Subject: BLUE Screen on SC Phones. Karen, I experienced the same thing when studying for the IE in my home lab. The solution for me to get rid of the very blue screen was to check the background image and revert to the standard image. Then my phones showed showed correct information. Michael Sears, CCIE(V)#38404 Cisco Certified Unfied Communications Computing Systems Specialist E911 Insrastructure Specialist Compucom Systems Western Region ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] UCCX prompt recording.
Drake, Not sure if this is still an open question but the location where the Spoken Name upload prompts are stored on the server is, *C:\Program Files\wfavvid\tomcat_appadmin\webapps\appadmin\upload* Let me know if that is what you're looking for? Regards Gurpreet On Fri, Jun 7, 2013 at 12:28 PM, Drake J jdrake...@gmail.com wrote: Hello Guys, I have a few questions on UCCX script for recording a prompt 1) How do I find out where my recorded prompt is being stored for a recording script I create? 2) If I am using spoken name upload and then using the Upload prompt ( step) just before the terminate step in the script then how do find where my recording has been stored? Many times in question ( 2) I can hear my recorded prompt . But when I search for it I don't find it. I checked the wfavvid folder as well and prompts section. Can someone help me out with the above 2 questions? Regards, Drake ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
