Re: [OSL | CCIE_Voice] MVA partial match issue
Debug h245 asn1 or debug voip application vxml. If no h245 open logical channel I suspect dial peer. Sent from my Verizon Wireless 4G LTE Smartphone Original message From: William Bell b...@ucguerrilla.com Date: 03/27/2013 6:38 PM (GMT-05:00) To: Sergey Heyphets ser...@heyphets.com Cc: ccie_voice@onlinestudylist.com, (ccie_voice@onlinestudylist.com) ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] MVA partial match issue I concur with Sergey. On Mar 27, 2013, at 2:14 PM, Sergey Heyphets wrote: The prompts you hear on the when you dial-in are the results of IOS executing the VXML script, which was defined in the application/service definition. When you, however, press 1 to make the call and enter the number, the VXML script instructs the IOS to place the call to the MVA number defined under media resources. So if you don't have the MVA number defined under Media Resources, the initial prompts would work, but placing the call would fail. Sergey On Wed, Mar 27, 2013 at 1:07 PM, Barrera, Hugo hugo.barr...@nexusis.com wrote: But would the MVA number still work on the gateway when you dial in? May it would huh because the MVA AA on the IOS is separate? Regards, Hugo From: William Bell [mailto:b...@ucguerrilla.com] Sent: Wednesday, March 27, 2013 4:47 AM To: Barrera, Hugo Cc: Justin Carney; donny f; ccie_voice@onlinestudylist.com, (ccie_voice@onlinestudylist.com); michael.se...@compucom.com; networksanitytoinsan...@gmail.com Subject: Re: [OSL | CCIE_Voice] MVA partial match issue I have ran into a similar problem. In my case I would get a fast busy after entering the extension number followed by #. The issue was I neglected to provision Mobile Voice Access under Media Resources. On Tuesday, March 26, 2013, Barrera, Hugo wrote: Regarding MVA during my first attempt (real lab) I had it working except for when I dialed in and tried to call another 4-digit ext like SAPH1 or SBPH2 any ideas why that didn’t work? Regards, Hugo From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Justin Carney Sent: Monday, March 25, 2013 1:51 AM To: donny f Cc: ccie_voice@onlinestudylist.com, (ccie_voice@onlinestudylist.com); michael.se...@compucom.com; networksanitytoinsan...@gmail.com Subject: Re: [OSL | CCIE_Voice] MVA partial match issue You can have the rd with 7 digits only and without the 9 for pstn access - use either application dial rules (match 7 digits, prefix 9) or a translation pattern to modify the rd to match your existing local route pattern. I'm not sure if there's an MVA bug in this version of cucm, but its pretty easy to configure it so that you always have a full match since you will likely have only one rd. This is what I do for the lab. A real world (for nanp) example of MVA partial match would be using e164 address for all rd (+1 npa-nxx-) and set partial match to 10 or 7 depending on whether all sites receive inbound ani as 10d for local calls or if any sites receives only 7d. This would also work for lab, but takes extra steps if you aren't already required to use + dialing For partial match to work, the rd must be longer than the inbound ani (ani 7d and rd +11d). You cannot use partial match with an ani longer than the rd (ani 10d and rd 7d), in this case your options would be to apply inbound transformation on the gateway to make rd ani shorter (ie match the rd) or make your rd longer and manipulate outbound dnis to make it route. On Mar 25, 2013 2:00 AM, donny f f.faraday...@gmail.com wrote: hi, I config the Service parameter for MVA , using partial match 7 digit . However when I dial the RD using 7 digit ,it never works. seem like UCM only take Full match. I heard this is bug, Any suggestion for the work around if still want to use partial match ? d On Sun, Mar 17, 2013 at 9:58 AM, michael.se...@compucom.com wrote: Greetings, I think you are doing everything right just need a few tweaks. Place a call from the PSTN line 2 to 3033300 and do debug isdn q931 on gateway. What digits do you see for the calling number. 7 or 10? If seeing 7 digits inbound change your Remote Destination Number to 525, without the 9. If you are seeing 10 digits inbound the NPA, NXX, TNTN change your remote destination number to XXX525, in other words match what you're seeing in the isdn debug for calling party and make that you're Remote Destination Number. Do NOT require the prefix of 9 on the Remote Destination Number. Also, under Remote Destination Information make sure you are putting a tick in Mobile Phone checkbox and a tick in the Enable Mobile Connect checkbox. Otherwise your configuration looks good. Hope you find this helpful. Michael Sears CCIE 38404 Date: Sun, 17 Mar 2013 18:23:01 +0530 From: sanity insanity networksanitytoinsan...@gmail.com To: ccie_voice@onlinestudylist.com Subject: [OSL |
Re: [OSL | CCIE_Voice] IntegratedServicesEngine bound to Loopback can ping but can't http to it?
I can ping the ISE from other sites. Just can't pull up the web page. Loking for cue command to view http traffic Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Andy Thanh tanthanh2...@gmail.com Date: 03/19/2013 7:31 PM (GMT-05:00) To: Sergey Heyphets ser...@heyphets.com Cc: Online Study (ccie_voice@onlinestudylist.com) ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] IntegratedServicesEngine bound to Loopback can ping but can't http to it? Did you advertise this network through ospf? This is for simple command: router ospf 1 network 0.0.0.0 255.255.255.255 area 0 On Wed, Mar 20, 2013 at 5:11 AM, Sergey Heyphets ser...@heyphets.com wrote: Jason, is your route to 110.32.60.253 ? On Tue, Mar 19, 2013 at 4:56 PM, Jason Aarons scubajas...@gmail.com wrote: What are some troubleshooting shooting steps for a CUE/IntegratedServicesEngine that is using ip unnumbered loopback0? I can ping the ISE locally and from remote sites, but I can’t get the http web page for the ISE to show (CME web page is good). I can ping 10.32.60.253 from another site but web page doesn’t come up in Internet Explorer. I can session to ISE (show tech page is correct), I have reset ISE, I have done a restore factory default. I have reloaded the router and the ISE. What else can I do? If I switch it to another interface, reload, etc it works fine (ping, web page, phones pilot number works fine). What are some CUE/ISE debug commands I should run to see if http traffic is making it to the CUE/ISE? Branch2# Int loopback0 Ip address 10.32.60.254 255.255.255.0 Ip ospf network point-to-point ! Int integrated-services-engine 1/0 Ip unnumbered loopback0 Ip ospf network point-to-point Service-module ip address 10.32.60.253 Service-module ip default-gateway 10.32.60.254 Keepalive 10 No shut ! Ip route 110.32.60.253 255.255.255.255 integrated-service-engine 1/0 Seems to me I’m missing something when using loopbacks for the CUE/ISE. -jason Could be some typo’s above this is from memory of my home lab, I’m not at home right now. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Question on Auto Qos WAN QoS
I've noticed this too, but don't have an explanation why. Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Ramcharan Arya ramcharan.a...@gmail.com Date: To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Question on Auto Qos WAN QoS Hi, I have noticed when I run AutoQoS on sub-interface it automatically add encapsulation CISCO on Inteface-dlci Config Prior to AutoQoS: interface Serial0/1/0 no ip address encapsulation frame-relay IETF no frame-relay inverse-arp frame-relay lmi-type ansi ! interface Serial0/1/0.1 point-to-point ip address 10.10.112.2 255.255.255.0 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 102 --- Configuration After AutoQoS interface Serial0/1/0.1 point-to-point ip address 10.10.112.2 255.255.255.0 ip ospf mtu-ignore snmp trap link-status frame-relay interface-dlci 102 CISCO - Encapsulation Cisco class AutoQoS-FR-Se0/1/0-1 auto qos voip trust Prior to auto configuration on my primary interface frame-relay encapsulation is IETF. I think encapsulation should be match after autoqos. Thanks Regards, Ramcharan Arya ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] cisco DocCD
I found memorizing as much as you can (e.g. urls) helps. Every minute you get helps. Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Chrysostomos Christofi ch.christ...@logicom.net Date: To: Jason Aarons scubajas...@gmail.com,'Cory Gray' corygray22...@hotmail.com,'CCIEing' aboaz...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: cisco DocCD yes we have to remind also and the urls J this will not be an expert , but a someone guy with 1000% memory From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Jason Aarons Sent: Δευτέρα, 14 Ιανουαρίου 2013 9:01 μμ To: 'Cory Gray'; 'CCIEing' Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] cisco DocCD As I found out via the CCIE Policies page there is no guarantee this page will be accessible. My first attempt the website was down both internal/external to Cisco. This is rather rare. However an expert can configure everything without access to the documentation site J http://www.cisco.com/cisco/web/psa/default.html?mode=prod http://www.cisco.com/web/learning/le3/ccie/policies/index.html#out CCIE Lab Exams: Equipment, System, or Network Outages ...Vouchers: Lab vouchers will only be extended if the lab equipment is rendered inoperable where a candidate cannot proceed with their exam within 2 hours by the CCIE Lab team. ... Unfortunately, while access to the documentation is an inconvenience it does not render the lab equipment itself inoperable such that you can not proceed with your exam. The CCIE Lab can only be responsible for equipment maintained in it's control, or the access to that equipment. We do have a case open regarding the issue, and IT is currently investigating it. From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Cory Gray Sent: Monday, January 14, 2013 11:23 AM To: CCIEing Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] cisco DocCD The doc cd was retired from the lab many years ago. It is now the support pages with the three windows for you to navigate through. Sent from my iPhone On Jan 14, 2013, at 11:18 AM, CCIEing aboaz...@gmail.com wrote: Hi All, I was practicing the cisco Documentation CD that will be available during the lab http://www.cisco.com/cisco/web/psa/default.html to get used on it, I was searching for the topic in unity connection How to set up the Phone View ,this topic is mentioned in the System Administration for Cisco Unity Connection Release 7.X (http://www.cisco.com/en/US/docs/voice_ip_comm/connection/7x/administration/guide/7xcucsag245.html) I was not able to find the path in the Doc CD, I used Google to fine this guide from cisco site. Do you guys practice the Doc CD - If not, then you have to, as this is the only documentation resource during the exam..-, do you know the Path to the system administration guide for the products. Awaiting your response, Appreciate that. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Passed
Congrats! Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Steffen Bruening stbruen...@gmail.com Date: To: ccie_voice ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Passed I went on Thursday to Brussels for my 2nd attempt and I got my results suprisingly today. I passed. CCIE 37891. I like to say thank you to all on you on the list which shares your questions and answers about the blueprint task and ipexpert labs. I also wanna say thank you to IPexpert for their really really good learning materials. Regards Steffen___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Question for test class
I would doubt a proctor would allow it. Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Chrysostomos Christofi ch.christ...@logicom.net Date: To: Online Study (ccie_voice@onlinestudylist.com) ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Question for test class For many peoples this question maybe it’s funny , but if you know I would like to know if I can bring an electronic cigarette into the class ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] UCCX one button login
Paste your one button login url. I bet you don't have IPAgentLogin.jsp Sent from my Verizon Wireless 4G LTE Smartphone Original message From: singh singh8...@in.com Date: To: whl...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] UCCX one button login hi Bill, Those fields are added to the users under the subscricption for each phone. However when I press the services button on the phone it still prompts me for the... Name Password Extension Instead of directly logging into the service. -- Original message -- From:Bill whl...@gmail.com Date: 31 Dec 12 23:28:24 Subject: Re: [OSL | CCIE_Voice] UCCX one button login To: Cc: ccie_voice@onlinestudylist.com So when you assign the service to the phone add those fields for each user, also when you create the service you can set defaults so one user works right away and you just edit the rest Bill On Dec 31, 2012, at 5:19 AM, singh singh8...@in.com wrote: hi Guys, I have configured 1 button login for my agent phones however when I press the services button it takes me to name , ext and password . I would like to configure it so that it directly logs in after I press the services button instead of having to enter the name , password and id -singh Get Yourself a cool, short @in.com Email ID now! ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com Get Yourself a cool, short @in.com Email ID now!___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUPS- Presence - deskphone mode not active
Ctigw is for OCS/Lync. You don't need to set it up unless you have OCS or Lync deskphone control. Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Gurpreet Singh Kukreja tycoononway1...@gmail.com Date: To: virajith vir...@rediffmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] CUPS- Presence - deskphone mode not active Just to add, the CtiGw application user on the CM should also have these roles and Deskphone user's phone assigned. On Tue, Dec 25, 2012 at 6:36 PM, Gurpreet Singh Kukreja tycoononway1...@gmail.com wrote: Does your end user have CTI Enabled and CTI controlled roles assigned? If not, then assign them. Make sure that you've assigned the TCP profile in the CUPS server for the Deskphone user. - Gurpreet On Wed, Dec 19, 2012 at 12:56 AM, virajith vir...@rediffmail.com wrote: hi Guys, In the client I get the option of deskphone mode in CUPC but when I select it the mode does not get applied. In show server health I see the Desk phone mode says Partially Connected(Primary) - Cannot Connect to Phone. I have checked the cti server / gateway profile and it is fine. What else to check? -Vir Catch India as it happens with the Rediff News App. To download it for FREE, click here ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUCM slow while changing service parameter
Is multicast moh enabled? Seems enabling multicast slows my vmware workstation down. Floods 239.x.x.x nonstop. Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Ramcharan Arya ramcharan.a...@gmail.com Date: To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] CUCM slow while changing service parameter Hello, My CUCM response is very slow when I update Cisco Callmanager service paramter. It is running on vm. Can you please suggest is there any setting on vm to improve the performance. Rest everything works normal. Please suggest if you have any technical detail to share about this. Regards, Ramcharan Arya ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CUCM slow while changing service parameter
Dors stopping multicast moh resolve the issue? Sent from my Verizon Wireless 4G LTE Smartphone Original message From: Ramcharan Arya ramcharan.a...@gmail.com Date: To: scubajasona scubajas...@gmail.com Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] CUCM slow while changing service parameter Yes MOH is configured as per task. Is there any workaroun/solution to fix this problem. Regards, Ramcharan Arya On Sat, Dec 22, 2012 at 9:04 AM, scubajasona scubajas...@gmail.com wrote: Is multicast moh enabled? Seems enabling multicast slows my vmware workstation down. Floods 239.x.x.x nonstop. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com