Re: [OSL | CCIE_Voice] 0 Conf max sessions
: CISCO2811 , VID: V03 , SN: FHK103671CU NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC102540TY NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC1032054R NAME: NM-SE on Slot 1, DESCR: NM-SE PID: NM-CUE, VID: V03, SN: FOC10120B2E NAME: 40GB IDE Disc Daughter Card on Slot 1 SubSlot 0, DESCR: 40GB IDE Disc Daughter Card PID: , VID: 1.0, SN: FOC10170V2B On Mon, Jul 7, 2008 at 9:14 AM, Onur Tufekci [EMAIL PROTECTED] wrote: I actually configured all that right after I send this message but no luck. On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi [EMAIL PROTECTED] wrote: try configuring sccp ccm and sccp ccm group before you set the max sessions. Vik Malhi – CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mehmet Tufekci Sent: Sunday, July 06, 2008 9:17 AM To: ccievoice1 Cc: OSL CCIE Voice Lab Exam Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
show inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V03 , SN: FHK103671CU NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC102540TY NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC1032054R NAME: NM-SE on Slot 1, DESCR: NM-SE PID: NM-CUE, VID: V03, SN: FOC10120B2E NAME: 40GB IDE Disc Daughter Card on Slot 1 SubSlot 0, DESCR: 40GB IDE Disc Daughter Card PID: , VID: 1.0, SN: FOC10170V2B On Mon, Jul 7, 2008 at 9:14 AM, Onur Tufekci [EMAIL PROTECTED] wrote: I actual ly configured all that right after I send this message but no luck. On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi [EMAIL PROTECTED] wrote: try configuring sccp ccm and sccp ccm group before you set the max sessions. Vik Malhi �C CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mehmet Tufekci Sent: Sunday, July 06, 2008 9:17 AM To: ccievoice1 Cc: OSL CCIE Voice Lab Exam Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown ! _ NEW! Get Windows Live FREE. http://www.get.live.com/wl/all
Re: [OSL | CCIE_Voice] 0 Conf max sessions
Daughter Card PID: , VID: 1.0, SN: FOC10170V2B On Mon, Jul 7, 2008 at 9:14 AM, Onur Tufekci [EMAIL PROTECTED] wrote: I actually configured all that right after I send this message but no luck. On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi [EMAIL PROTECTED] wrote: try configuring sccp ccm and sccp ccm group before you set the max sessions. Vik Malhi – CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communitieshttp://www.ipexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mehmet Tufekci Sent: Sunday, July 06, 2008 9:17 AM To: ccievoice1 Cc: OSL CCIE Voice Lab Exam Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
You need to blow away your controllers (remove the pri or ds0 group) and THEN create your conf bridges then you can create your pri or ds0 groups. Jonathan On Sun, Jul 6, 2008 at 11:17 AM, Mehmet Tufekci [EMAIL PROTECTED] wrote: I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
I actually configured all that right after I send this message but no luck. On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi [EMAIL PROTECTED] wrote: try configuring sccp ccm and sccp ccm group before you set the max sessions. Vik Malhi – CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: [EMAIL PROTECTED] [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communities http://www.ipexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- *From:* [EMAIL PROTECTED] [mailto: [EMAIL PROTECTED] *On Behalf Of *Mehmet Tufekci *Sent:* Sunday, July 06, 2008 9:17 AM *To:* ccievoice1 *Cc:* OSL CCIE Voice Lab Exam *Subject:* Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
Here is the configuration and results: router2(config)#do show run Building configuration... Current configuration : 2938 bytes ! ! Last configuration change at 15:11:09 UTC Mon Jul 7 2008 ! NVRAM config last updated at 14:49:04 UTC Mon Jul 7 2008 ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname router2 ! boot-start-marker boot-end-marker ! card type t1 0 0 no logging console enable secret 5 $1$7cJ4$U9gWuPCv.H1DPdXYIyWJD0 ! no aaa new-model ! resource policy ! network-clock-participate wic 0 ! ! ip cef ! ! no ip domain lookup ! isdn switch-type primary-ni ! voice-card 0 dspfarm dsp services dspfarm ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! controller T1 0/0/0 framing esf linecode b8zs ! controller T1 0/0/1 framing esf linecode b8zs ! ! ! ! interface FastEthernet0/0 ip address 192.168.2.1 255.255.255.0 duplex full speed 100 h323-gateway voip bind srcaddr 192.168.2.1 ! interface FastEthernet0/1 description Management_IP ip address 192.168.10.2 255.255.255.0 duplex full speed 100 ! interface Service-Engine1/0 no ip address shutdown ! ip route 192.168.1.0 255.255.255.0 192.168.10.1 ip route 192.168.3.0 255.255.255.0 192.168.10.3 ! ip http server no ip http secure-server ! ! ! ! control-plane ! ! ! ! ! sccp local FastEthernet0/0 sccp ccm 192.168.2.1 identifier 1 sccp ! sccp ccm group 1 associate ccm 1 priority 1 associate profile 2 register xcoder associate profile 1 register conference ! dspfarm profile 2 transcode codec g711ulaw codec g729r8 maximum sessions 4 associate application SCCP shutdown ! dspfarm profile 1 conference codec g711ulaw codec g729r8 maximum sessions 1 associate application SCCP shutdown ! ! dial-peer voice 1000 voip answer-address 1... destination-pattern 1... session target ipv4:192.168.1.1 codec g711ulaw ! dial-peer voice 9 pots destination-pattern 9T incoming called-number 14345552... direct-inward-dial ! ! ! telephony-service max-ephones 2 max-dn 2 ip source-address 192.168.2.1 port 2000 auto assign 1 to 2 system message Your current options sdspfarm units 5 sdspfarm tag 1 xcoder sdspfarm tag 2 conference dialplan-pattern 1 14345552... extension-length 4 max-conferences 8 gain -6 call-forward pattern .T web admin system name cisco password cisco dn-webedit time-webedit transfer-system full-consult transfer-pattern .T secondary-dialtone 9 ! ! ephone-dn 1 dual-line number 2001 description 14345552001 name Gil Grissom ! ! router2(config)#dspfarm router2(config)# router2(config)# router2(config)# router2(config)#dspfarm pro 2 router2(config-dspfarm-profile)#no shut router2(config-dspfarm-profile)#dspfarm pro 1 router2(config-dspfarm-profile)#no shut Enabling profile failed due to insufficient CONFERENCING resources, resources available to support 0 sessions; please modify the configuration and retry router2(config-dspfarm-profile)#do show inv NAME: 2811 chassis, DESCR: 2811 chassis PID: CISCO2811 , VID: V03 , SN: FHK103671CU NAME: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot 0, DESCR: VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1 PID: VWIC2-2MFT-T1/E1 , VID: V01 , SN: FOC102540TY NAME: PVDMII DSP SIMM with one DSP on Slot 0 SubSlot 4, DESCR: PVDMII DSP SIMM with one DSP PID: PVDM2-16 , VID: V01 , SN: FOC1032054R NAME: NM-SE on Slot 1, DESCR: NM-SE PID: NM-CUE, VID: V03, SN: FOC10120B2E NAME: 40GB IDE Disc Daughter Card on Slot 1 SubSlot 0, DESCR: 40GB IDE Disc Daughter Card PID: , VID: 1.0, SN: FOC10170V2B On Mon, Jul 7, 2008 at 9:14 AM, Onur Tufekci [EMAIL PROTECTED] wrote: I actually configured all that right after I send this message but no luck. On Sun, Jul 6, 2008 at 11:23 PM, Vik Malhi [EMAIL PROTECTED] wrote: try configuring sccp ccm and sccp ccm group before you set the max sessions. Vik Malhi – CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: [EMAIL PROTECTED] [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communities http://www.ipexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- *From:* [EMAIL PROTECTED] [mailto: [EMAIL PROTECTED] *On Behalf Of *Mehmet Tufekci *Sent:* Sunday, July 06, 2008 9:17 AM *To:* ccievoice1 *Cc:* OSL CCIE Voice Lab Exam *Subject:* Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run
Re: [OSL | CCIE_Voice] 0 Conf max sessions
PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communitieshttp://www.ipexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. -- *From:* [EMAIL PROTECTED] [mailto: [EMAIL PROTECTED] *On Behalf Of *Mehmet Tufekci *Sent:* Sunday, July 06, 2008 9:17 AM *To:* ccievoice1 *Cc:* OSL CCIE Voice Lab Exam *Subject:* Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
before you set the max sessions. Vik Malhi – CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mehmet Tufekci Sent: Sunday, July 06, 2008 9:17 AM To: ccievoice1 Cc: OSL CCIE Voice Lab Exam Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
Re: [OSL | CCIE_Voice] 0 Conf max sessions
try configuring sccp ccm and sccp ccm group before you set the max sessions. Vik Malhi - CCIE #13890 Senior Technical Instructor - IPexpert, Inc. Telephone: +1.810.326.1444 Fax: +1.810.454.0130 Mailto: mailto:[EMAIL PROTECTED] [EMAIL PROTECTED] Join our free online support and peer group communities: http://www.IPexpert.com/communities IPexpert - The Global Leader in Self-Study, Classroom-Based, Video-On-Demand and Audio Certification Training Tools for the Cisco CCIE RS Lab, CCIE Security Lab, CCIE Service Provider Lab , CCIE Voice Lab and CCIE Storage Lab Certifications. _ From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Mehmet Tufekci Sent: Sunday, July 06, 2008 9:17 AM To: ccievoice1 Cc: OSL CCIE Voice Lab Exam Subject: Re: [OSL | CCIE_Voice] 0 Conf max sessions I have 1-3 configured under controller. I am able to see 1-8 available resources under my transcoder profile but no luck with conference. I know conference will not show up if you enable transcoder profile first. No matter what I tried I can not get it to run. On Jul 6, 2008, at 11:44 AM, ccievoice1 wrote: have you utilized all the dsp resources for your pri-group? On Sun, Jul 6, 2008 at 11:31 PM, Mehmet Tufekci [EMAIL PROTECTED] wrote: Hi All, I can not figure out why maximum session 0-0 is showing under conference profile. I did not enable transcoding profile yet. voice-card 0 dspfarm dsp services dspfarm ! ! ! interface Loopback0 ip address 172.3.102.1 255.255.255.255 ip ospf network point-to-point ! ! sccp local Loopback0 sccp ! dspfarm profile 1 transcode codec g711ulaw codec g729r8 shutdown ! dspfarm profile 2 conference codec g711ulaw codec g729r8 shutdown !
