Lab Purchase Deal
Hello Friend, I am negotiating to buy following routers from a student. These routers were purchased new one year ago and only used exclusively Lab practice. I would appreciate, if someone can guide me at what price to buy. One Cisco 2509 with async cable 1- 9 16RAM/8FLASH Two Cisco 2513 with three TR Cables with 16RAM/16FLASH One Cisco 2520 with 16RAM/16FLASH Two Cisco 2501's with 16RAM/16FLASH Six AUI to Ethernet Transceviers Six Back-to-Back DTE-DCE 3' Cables One 8 Port Token Ring Hub Anew1 & Anew2 Lab Configs Enterprise IOS 11.3.9 & 12.06 on CD Power Cords,Ears,& Console Cables 6 No for each Router Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2504 At what price to buy???????
Hello Gang, I am trying to negotiate the price for above router at USD.425 + shipping. Is the price reasonable. The router comes with 16R/8F and power cord. No other accessories included. Your input would be appreciated. Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Router 2513
Hello Gang, I am looking for 2513 with 16R/16F. There are quite a few at ebay. Most of the sellers are not interested shipping to Canada. Anybody on the list interested to sell one. Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2511
Hello Friends, I am planning to buy this router. What's the fair price? Your comments appreciated. 2511 16F/32R 2 Octal Cables + Rack Hardware 68030 Processor - Revision M 16384K bytes of processor board system flash (read only) Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2511
Hello Gang, Would appreciate your comment to the following. Router 2511 with 16R/8F - USD.950 1 Octal Cable, 1 power adapter, 1 Mounting Kit, 1 Serial to V.35 DCE, 1 Transceiver, 6 Modem adapters, 1 Console Cable, 1 Serial to Console Adapter, 1 Cisco IP Feature Pack 12.0 Kit & Free Shipping. Is it a good deal? Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2511 output
Hello Gang, I am trying to buy 2511 router. I asked for show line & show version output. Do you guy's see any error in the output. The seller upgraded the flash and failed. show line Tty TypTx/RxA Modem Roty AccO AccI UsesNoise Overruns * 0 CTY -- --- 000 1 AUX 9600/9600 -- --- 000 2 VTY 9600/9600 -- --- 000 3 VTY 9600/9600 -- --- 000 4 VTY 9600/9600 -- --- 000 5 VTY 9600/9600 -- --- 000 6 VTY 9600/9600 -- --- 000 3000 Bootstrap Software (IGS-RXBOOT), Version 9.14(9.b), MAINTENANCE INTERIM SOFTWARE Patchlevel = 9.1(12.6) Copyright (c) 1986-1995 by cisco Systems, Inc. Compiled Fri 03-Feb-95 07:11 by chansen show version System Bootstrap, Version 4.14(9.1), SOFTWARE Router uptime is 2 minutes System restarted by power-on Running default software cisco 2500 (68030) processor (revision D) with 16380K/2048K bytes of memory. Processor board serial number 01904229 DDN X.25 software, Version 2.0, NET2 and BFE compliant. 1 Ethernet/IEEE 802.3 interface. 2 Serial network interfaces. 32K bytes of non-volatile configuration memory. 8192K bytes of processor board System flash (Read/Write) Configuration register is 0x2102 Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Silly Question - Curious to know
Hello Gang, Is it possible to find how old is a router based on the show version or any other output. Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
2501 help
Hello Friends, I am new to this field. Received couple of routers today. Trying to learn basic commands.When I enter config t following is the output RouterA#config t Enter configuration commands, one per line. Edit with DELETE, CTRL/W, and CTRL/U; end with CTRL/Z I don't get RouterA prompt. What could be the problem? Thanks Gopal _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Anybody from Toronto
Hello Gang, Anybody on the list from Toronto studying for CCNA/CCNP/CCDP/CCIE. I have set up a massive lab at home. Facing few problems in configuration/upgrading. Over and above have no access to CCO. I even signed up for Consultant Program at Cisco site. It does not allow me to download latest version of ios. I understand Cisco does not want to give anything for free. Anybody willing to extend the help. I am willing to compensate financial for the time spent during set up. Thanks RamG _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Flash [7:713]
Hello Gang - I am looking for 8 MB flash for 2501 & 2502. Can someone help with the link. I tried browsing the net and found couple of sites where they sell 8MB flash for USD.199. I am looking for something less. I tried ebay. Either the shipping is way too high or the seller is not interested to ship to Canada. Any help would be appreciated. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=713&t=713 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Flash Upgrade Q's [7:1400]
Hello Gang - Hope some1 can help me on this. I am trying to upgrade ios. Following is the detail when command copy is issued. R2501#copy tftp flash You cannot copy to Flash address space while running code from it. The procedure below can be used to do the copy by reloading and using the ROM-based bootstrap image. Refer to the product documentation for a detailed description. 1. Save the system configuration (using 'write mem') if necessary. 2. Type in 'config term' to enter configuration mode. 3. Enter 'config 0x2101' to set the soft configuration register. 4. Enter '^Z' to exit configuration mode. 5. Enter 'reload' command to reload the system. 6. If you have a remote Telnet connection, terminate it, give the router some time to reload, then reconnect. 7. Enter 'enabled' mode and execute the copy command. 8. Repeat steps 2 to 6 above, but this time in step 3, enter 'config 0x2102'. Followed above procedure. Returned with this error. R2501(boot)>enable Password: R2501(boot)#copy tftp flash ERR: Device in READ-ONLY state What command to use to change the flash to READ/WRITE state. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1400&t=1400 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
BOOT-2500= bios [7:1412]
I will be getting couple of 8MB flash {3rd Party}. As per seller BOOT-2500 bios will be needed to recognize the flash upgrade. I heard Cisco provides this item for free but have to pay shipping charge. I am unable to find the link at Cisco site. Does any one has the link. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1412&t=1412 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IOS for Home Lab [7:1531]
I have home lab of 7 routers with 16RAM/16FLASH. Which ios should I install on these routers to practice each and every ccie lab scenarios. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1531&t=1531 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Beware of VINCENT CHONG [7:1631]
Hello Gang Just want to keep you all informed on the board not to deal in any form of TRADE {CCIE Material }or BUYING accessories from VINCENT CHONG. I had a bad experience today. We had entered into an agreement to trade CCIE materials. I sent him soft copy of my materials and requested him to make hard copy of his material. The price for hard copy of his material was mutually agreed at USD.22. I sincerely sent him the money through pay pal. To my surprise he has declined accepting the money and is not interested to send the material. Like a KID he sent me this reply Quote "I will send back your material and I do not want to trade anymore. I will removed from my hard disk." Is this the way CHINESE behave. Surprised. This is not a complaint. Beware of this GUY - VINCENT CHONG. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1631&t=1631 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Beware of VINCENT CHONG [7:1634]
Hello Gang Don't want to waste the bandwidth. This will be my last response on this subject. Solution Lab price as quoted by Vincent is true, but it was not part of the trade. He showed interest and I quoted the price. The photo copying of 435 Pages & postage is costing way more than my quote. Hence, I revised the price. I repeat Solution Lab was not part of the trade. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1634&t=1634 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
4MB Flash [7:1642]
Hello Friends - With the help of a friend, I will be upgrading all my Routers this week. As a result, I will be left with FIVE 4 MB flash. Anybody on the list would be interested, is so, contact me directly. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=1642&t=1642 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
MGS 2513 - Yr suggestions Pls [7:2090]
Hello Gang - Can this router be purchased to be part of my lab. Price seems to be very attractive compared to 2513 at ebay which are around USD.850+. Your suggestions appreciated. Thanks / RamG Cisco MGS Router with 11.0(22) IOS, 2 Ethernet, 2 Serial, and 1 Token Ring Ports This router contains the following cards: 1 MC+ 4MB Flash Card 1 CSC/4 Processor Card with 16 MB RAM, 68040 Processor, and IOS 11.0(22) in Flash 1 CSC-1E2T Ethernet/Serial Controller, the fast kind, for speeds up to 4Mbps 1 CSC-1E Ethernet Controller 1 CSC-R16M Token Ring Controller And has the following interfaces: 2 V.35 High Density Serial Ports, these ports easily do DCE & DTE with clockrate commands. 2 Ethernet AUI Ports 1 Token Ring Port 1 DB-25 Console Port Cisco Internetwork Operating System Software IOS (tm) GS Software (GS3-AK-M), Version 11.0(22), RELEASE SOFTWARE (fc1) Copyright (c) 1986-1998 by cisco Systems, Inc. Compiled Tue 08-Dec-98 04:54 by jaturner Image text-base: 0x1000, data-base: 0x006EAC94 cisco CSC4 (68040) processor with 16384K bytes of memory. Bridging software. X.25 software, Version 2.0, NET2, BFE and GOSIP compliant. 2 MCI controllers (2 Ethernet, 2 Serial). 2 Ethernet/IEEE 802.3 interfaces. 1 Token Ring/IEEE 802.5 interface. 32K bytes of non-volatile configuration memory. 4096K bytes of flash memory on MC+ card (via MCI). Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=2090&t=2090 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Flash Partition [7:2769]
How to combine the flash partition into ONE 16F R2501#show flash System flash directory, partition 1: No files in System flash [0 bytes used, 8388608 available, 8388608 total] 8192K bytes of processor board System flash (Read/Write) System flash directory, partition 2: File Length Name/status 1 4554932 igs-ir-l.110-10.3 [4554996 bytes used, 3833612 available, 8388608 total] 8192K bytes of processor board System flash (Read/Write) Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=2769&t=2769 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Flash for sale - 2500 Series [7:3026]
After upgrading my routers, I am left with TWO 8 MB flash & TWO 4MB flash. I would like to sell them. If anyone is interested contact me directly. Details of Flash: 8MB - Intel - E28F008SA - U40124PI - 1991 8MB - Transcend - AM29F016D - TS8MCS1X8F - 0049ABD H - 1999 - Made in Taiwan 4MB - Intel - E28F008SA - U52112T7D - 1991 4MB - Intel - E28F008SA - U52112T7D - 1991 Guaranteed not DOA. Payable in Money Order OR Cash. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=3026&t=3026 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Last minute Tips on CCIE written Exam [7:3085]
He is expressing the bad experience he had with VC in trading CCIE materials "I think". I was also a victim. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=3193&t=3085 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
ios 12.2 upgrade errrrrrrr [7:4396]
I upgraded the ios to 12.2. When the router start following error appears. Any idea what it is? Trying R2501 (1.1.1.1, 2001)... Open cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of memory. Processor board ID 01560991, with hardware revision Bridging software. X.25 software, Version 3.0.0. SuperLAT software (copyright 1990 by Meridian Technology Corp). TN3270 Emulation software. 1 Ethernet/IEEE 802.3 interface(s) 2 Serial network interface(s) 32K bytes of non-volatile configuration memory. 16384K bytes of processor board System flash (Read ONLY) ip kerberos source-interface any - {This is the error Invalid input} ^% Invalid input detected at '^' marker. Press RETURN to get started! Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4396&t=4396 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Router 2523 [7:4829]
Hello Gang - I am planning to buy 2523. Before, I do that, I would like to have your opinions/suggestions. The purpose of buying 2523 is to practice FR config from All In One Study Guide Book. I have 2501/02/03/04/11 routers. Can I connect serial int of these routers to 2523 - 8 Low speed serial(sync/async) interfaces. Any command to be used? Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=4829&t=4829 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
R 2523 [7:5280]
Gang - Is USD.590 for above router without flash is worth buying? Thanks for your feedback. RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=5280&t=5280 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Media Filters For Sale [7:6109]
I have FOUR Media Filters for sale {Black Box/Simware}. Interested buyers contact me directly. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6109&t=6109 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
TR Int Errr [7:6112]
Hello Gang - I am having problem bring up TR int. Following is the output. R2502#show interface tokenring0 TokenRing0 is initializing, line protocol is down Hardware is TMS380, address is .30ba.4a52 (bia .30ba.4a52) MTU 4464 bytes, BW 16000 Kbit, DLY 630 usec, rely 255/255, load 1/255 Encapsulation SNAP, loopback not set, keepalive set (10 sec) ARP type: SNAP, ARP Timeout 04:00:00 Ring speed: 16 Mbps Duplex: half Mode: Classic token ring station Group Address: 0x, Functional Address: 0x0800 Ethernet Transit OUI: 0x00 Last input never, output never, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 54 interface resets 0 output buffer failures, 0 output buffers swapped out 59 transitions R2502#show config Using 774 out of 32762 bytes ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption service udp-small-servers service tcp-small-servers ! hostname R2502 ! no logging console enable password ram ! ip subnet-zero no ip domain-lookup ! ! ! interface Serial0 bandwidth 64 no ip address no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache ! interface Serial1 bandwidth 64 ip address 10.1.5.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache ! interface TokenRing0 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache ring-speed 16 ! ip classless ! ! line con 0 transport input none line aux 0 transport input all line vty 0 4 login ! end Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6112&t=6112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Curious Q [7:6114]
I have 5 routers. When I issue show ver each router returns different output regarding how the router was started. Is something wrong? R2501 uptime is 23 minutes System returned to ROM by power-on System image file is "flash:c2500-js-l.122-1.bin" R2502 uptime is 26 minutes System restarted by power-on System image file is "flash:c2500-i-l.120-9.bin" R2503 uptime is 24 minutes System returned to ROM by power-on System image file is "flash:c2500-js-l.122-1.bin" R2504 uptime is 26 minutes System restarted by power-on System image file is "igs-ir-l.110-10.3", booted via flash 2511 uptime is 27 minutes System restarted by power-on System image file is "c2500-js-l.112-9.bin", booted via flash Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6114&t=6114 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: TR Int Errr [7:6112]
Hello Gang - I am having problem bring up TR int. Following is the debug output. R2502#debug token ring Token Ring Interface debugging is on R2502# 02:46:48: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring beaconing 02:46:50: TR0 starting. 02:47:12: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring beaconing 02:47:14: TR0 starting. 02:47:35: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring beaconing 02:47:37: TR0 starting. 02:47:59: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring beaconing 02:48:01: TR0 starting. I browsed through cisco site to figure out what is the problem with TR based on above debug output. Following is the answer. Can somebody help me to bring up the TR. Ring Beacon The interface is transmitting beacon frames onto the ring. Something is wrong with the ring. R2502#show interface tokenring0 TokenRing0 is initializing, line protocol is down Hardware is TMS380, address is .30ba.4a52 (bia .30ba.4a52) MTU 4464 bytes, BW 16000 Kbit, DLY 630 usec, rely 255/255, load 1/255 Encapsulation SNAP, loopback not set, keepalive set (10 sec) ARP type: SNAP, ARP Timeout 04:00:00 Ring speed: 16 Mbps Duplex: half Mode: Classic token ring station Group Address: 0x, Functional Address: 0x0800 Ethernet Transit OUI: 0x00 Last input never, output never, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 0 packets input, 0 bytes, 0 no buffer Received 0 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort 0 packets output, 0 bytes, 0 underruns 0 output errors, 0 collisions, 54 interface resets 0 output buffer failures, 0 output buffers swapped out 59 transitions R2502#show config Using 774 out of 32762 bytes ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption service udp-small-servers service tcp-small-servers ! hostname R2502 ! no logging console enable password ram ! ip subnet-zero no ip domain-lookup ! ! ! interface Serial0 bandwidth 64 no ip address no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache ! interface Serial1 bandwidth 64 ip address 10.1.5.1 255.255.255.0 no ip directed-broadcast encapsulation ppp no ip route-cache no ip mroute-cache ! interface TokenRing0 no ip address no ip directed-broadcast no ip route-cache no ip mroute-cache ring-speed 16 ! ip classless ! ! line con 0 transport input none line aux 0 transport input all line vty 0 4 login ! end Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6132&t=6112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: TR Int Errr [7:6112]
It is startup-config info. I tried changing ring speed to 4 & later to 16 to see it could fix the problem. Changing the ring speed did not do any good. Thanks / RamG ""Larry trav"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Newbie question, > > On your router is the "show conf" giving us the contents of the > startup-config or the running-config? On your router are they both the same? > Saved? > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6135&t=6112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Curious Q [7:6114]
Thanks to I & others for the feedback. Learnt that different ios can show different output in show ver. I was curious to find out is something wrong after upgrade. I did not notice this before. Thanks / RamG ""ElephantChild"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > On Mon, 28 May 2001, RamG wrote: > > > > > E - Output of show ver for one of the router which returned to ROM by > > power-on. I recently upgraded ios to 12.2 ver. Did I make any mistake > > during upgrade. > > 1. Please share with the list. Just because I answered your initial > question doesn't mean that I will answer the followup. And even if I do, > others may learn from the thread. I cc'd the list on this. Please do so > on any follow-up. > > 2. Again, not necessarily. Compare *all* the information that show ver > gives you across all routers, and I'm pretty sure you will see different > ROM versions, or different IOS versions, or both, that explain the > slightly different messages that you see. > > 3. Is this your only cause for worry? Or are there other problems that > you think may be linked to this one? If so, what are they? > > > RamG > > > > R2501#show ver > > Cisco Internetwork Operating System Software > > IOS (tm) 2500 Software (C2500-JS-L), Version 12.2(1), RELEASE SOFTWARE > (fc2) > > Copyright (c) 1986-2001 by cisco Systems, Inc. > > Compiled Fri 27-Apr-01 16:11 by cmong > > Image text-base: 0x03076B18, data-base: 0x1000 > > > > ROM: System Bootstrap, Version 11.0(10c)XB1, PLATFORM SPECIFIC RELEASE > > SOFTWARE (fc1) > > BOOTFLASH: 3000 Bootstrap Software (IGS-BOOT-R), Version 11.0(10c)XB1, > > PLATFORM SPECIFIC RELEA > > SE SOFTWARE (fc1) > > > > R2501 uptime is 1 hour, 41 minutes > > System returned to ROM by power-on > > System image file is "flash:c2500-js-l.122-1.bin" > > > > cisco 2500 (68030) processor (revision D) with 16384K/2048K bytes of > memory. > > Processor board ID 01560991, with hardware revision > > Bridging software. > > X.25 software, Version 3.0.0. > > SuperLAT software (copyright 1990 by Meridian Technology Corp). > > TN3270 Emulation software. > > 1 Ethernet/IEEE 802.3 interface(s) > > 2 Serial network interface(s) > > 32K bytes of non-volatile configuration memory. > > 16384K bytes of processor board System flash (Read ONLY) > > > > Configuration register is 0x2102 > > > > -Original Message- > > From: ElephantChild [mailto:[EMAIL PROTECTED]] > > Sent: Monday, May 28, 2001 8:49 AM > > To: RamG > > Cc: [EMAIL PROTECTED] > > Subject: Re: Curious Q [7:6114] > > > > > > On Mon, 28 May 2001, RamG wrote: > > > > > I have 5 routers. When I issue show ver each router returns different > > > output regarding how the router was started. Is something wrong? > > > > Not necessarily. It could be nothing more than a difference in ROM > > versions or IOS versions. Have you looked at the rest of what show ver > > tells you? > > > > > R2501 uptime is 23 minutes > > > System returned to ROM by power-on > > > System image file is "flash:c2500-js-l.122-1.bin" > > > > > > R2502 uptime is 26 minutes > > > System restarted by power-on > > > System image file is "flash:c2500-i-l.120-9.bin" > > > > > > R2503 uptime is 24 minutes > > > System returned to ROM by power-on > > > System image file is "flash:c2500-js-l.122-1.bin" > > > > > > R2504 uptime is 26 minutes > > > System restarted by power-on > > > System image file is "igs-ir-l.110-10.3", booted via flash > > > > > > 2511 uptime is 27 minutes > > > System restarted by power-on > > > System image file is "c2500-js-l.112-9.bin", booted via flash > > > > -- > > "Someone approached me and asked me to teach a javascript course. I was > > about to decline, saying that my complete ignorance of the subject made > > me unsuitable, then I thought again, that maybe it doesn't, as driving > > people away from it is a desirable outcome." --Me > > > > > > > > > -- > "Someone approached me and asked me to teach a javascript course. I was > about to decline, saying that my complete ignorance of the subject made > me unsuitable, then I thought again, that maybe it doesn't, as driving > people away from it is a desirable outcome." --Me > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6137&t=6114 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: TR Int Errr [7:6112]
I have TWO routers with TR interface - 2502/2504. I am using IBM MAU. Connected both the routers TR int to MAU port 1 & 2. Router 2504 TR Int is up and running fine. I am having problem with 2502. There is no fault on MAU. What else could be the problem? I even changed ring speed on 2502. Yet it is still initializing and protocol is DOWN. I even tried changing media filters. Still no luck in troubleshooting. I am worried is my TR int gone for good, if so, then I will have to report the defect to the seller ASAP. Would appreciate any help. Hello Gang - I am having problem bring up TR int. Following is the output. > > R2502#show interface tokenring0 > TokenRing0 is initializing, line protocol is down > Hardware is TMS380, address is .30ba.4a52 (bia .30ba.4a52) > MTU 4464 bytes, BW 16000 Kbit, DLY 630 usec, rely 255/255, load 1/255 > Encapsulation SNAP, loopback not set, keepalive set (10 sec) > ARP type: SNAP, ARP Timeout 04:00:00 > Ring speed: 16 Mbps > Duplex: half > Mode: Classic token ring station > Group Address: 0x, Functional Address: 0x0800 > Ethernet Transit OUI: 0x00 > Last input never, output never, output hang never > Last clearing of "show interface" counters never > Queueing strategy: fifo > Output queue 0/40, 0 drops; input queue 0/75, 0 drops > 5 minute input rate 0 bits/sec, 0 packets/sec > 5 minute output rate 0 bits/sec, 0 packets/sec > 0 packets input, 0 bytes, 0 no buffer > Received 0 broadcasts, 0 runts, 0 giants, 0 throttles > 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort > 0 packets output, 0 bytes, 0 underruns > 0 output errors, 0 collisions, 54 interface resets > 0 output buffer failures, 0 output buffers swapped out > 59 transitions > > R2502#show config > Using 774 out of 32762 bytes > ! > version 12.0 > service timestamps debug uptime > service timestamps log uptime > no service password-encryption > service udp-small-servers > service tcp-small-servers > ! > hostname R2502 > ! > no logging console > enable password ram > ! > ip subnet-zero > no ip domain-lookup > ! > ! > ! > interface Serial0 > bandwidth 64 > no ip address > no ip directed-broadcast > encapsulation ppp > no ip route-cache > no ip mroute-cache > ! > interface Serial1 > bandwidth 64 > ip address 10.1.5.1 255.255.255.0 > no ip directed-broadcast > encapsulation ppp > no ip route-cache > no ip mroute-cache > ! > interface TokenRing0 > no ip address > no ip directed-broadcast > no ip route-cache > no ip mroute-cache > ring-speed 16 > ! > ip classless > ! > ! > line con 0 > transport input none > line aux 0 > transport input all > line vty 0 4 > login > ! > end Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6201&t=6112 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Required TR for Lab Practice [7:6601]
Hello - General Q - How many TR int required for CCIE lab practice? I have 2 routers with TR. Thanks / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=6601&t=6601 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Troubleshooting question? [7:7763]
IMO it is not possible to clear the lab without sufficient exposure to various tech. You would be better off spending the lab money on short training course and get equipped with all that is required to pass the lab on first attempt. HTH / RamG wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > He is my situation in a nutshell. Can some one help me troubleshoot this. > > I. I don't have any router's with token ring interface. > 2. I don't have any VIC modules so I can't do VOICE. > 3. I don't have a CAT with a LS1010. > 4. I don't have extra money for equipment > 5. I don't have extra money for online time with virtual racks. > > I do how ever have access to 1600, 2500 and a 7000 with Ethernet, serial and > BRI interfaces. I also have a Atlas 550 so I can practice Frame and ISDN > material. > > I still want my CCIE. > > Can I pass the Token Ring (DLSw RSRB), ATM and Voice portions of the LAB with > book knowledge alone? > > I passed the CCNA, CCDA and CCNP with book knowledge. > > Is anyone else in a similar situation? Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=7775&t=7763 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
TR Error [7:8554]
I have 2 routers {2502 & 2504}. Both TR are connected to ANDREW MAU 8228. I am unable to bring up the interface. I tried setting ring speed to 4 & 16 but unsuccessful. I am using black box LT 056A Media Filters. I did check the archives. Mr. Vincent Chong faced similar problem on 29th March 2001 but there was no solution posted at the archive. This is what I found - Problem fixed. Just follow Cisco recommendation and it works. Would appreciate, if he can share whatever info he was referring too. Msg being copied to VINCENT CHONG for help. What is meant by wrong idb state? I see this in debug event output Following is the interface & debug events output. 2504#show ip int brief Interface IP-Address OK? Method Status Protocol BRI0 unassigned YES NVRAM administratively down down BRI0:1 unassigned YES unset administratively down down BRI0:2 unassigned YES unset administratively down down Serial0192.1.1.2 YES NVRAM down down Serial1193.1.1.2 YES NVRAM down down TokenRing0 unassigned YES NVRAM initializing down 00:43:02: TR0 starting. 00:43:23: TR0 receive SRB_FREE, state=2, if_state=6 00:43:24: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring beaconing 00:43:24: %TR-3-BADSTART: Unit 0, Start completion and wrong idb state - state= 0 00:43:25: TR0: reset from 308F4F6 00:43:25: TR0: txtmr: 0x0, msclk: 0x27C15C, qt: 0x0 (2605400ms) Following is the condensed startup config output. R2504#show config Using 918 out of 32762 bytes ! version 12.2 no service single-slot-reload-enable service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname R2504 interface TokenRing0 no ip address ring-speed 4 TX / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=8554&t=8554 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: TR Error [7:8554]
Hello Friends - Its me again with TR problem. I tried each router individually with different media filters. Still unsuccessful in getting the int up. I ran through Cisco site with the error code - idb state. That is what I found. Can someone tell me what kind of media filters, I should use. I have a strong feeling it is the media filter causing the trouble. Any thoughts would be appreciated. Cisco site search feedback: On Error code idb state: Error Message: %TR-3-BADSTART Unit [dec], Start completion and wrong idb state -state= [dec] %TR-4-BKGND Unit [dec], bkgnd int: last packet out [dec]ms %TR-4-BKGNDINT Unit [dec], bkgnd int: [hex][hex] [hex][hex][hex][hex] [hex][hex] %TR-3-COMPFAIL Unit [dec], Tbuf completion failure, result 0x[hex] %TR-3-FILTFAIL Unit [dec], SRB filter set failed: 0x[hex] 0x[hex]0x[hex] 0x[hex] (blk 0x[hex]) downing %TR-3-GETCONF Unit [dec], get_config failed, result 0x[hex] 0x[hex] Explanation: The Token Ring interface contains firmware that is incompatible with the system software. Recommended Action: Call Cisco Systems to upgrade the Token Ring Monitor firmware and/or the system software. I don't have maintenance contract with Cisco. It's my home lab that I am trying to fix. TIA / RamG ""RamG"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > I have 2 routers {2502 & 2504}. Both TR are connected to ANDREW MAU 8228. > I am unable to bring up the interface. I tried setting ring speed to 4 & 16 > but unsuccessful. I am using black box LT 056A Media Filters. > > I did check the archives. Mr. Vincent Chong faced similar problem on 29th > March 2001 but there was no solution posted at the archive. This is what I > found - Problem fixed. Just follow Cisco recommendation and it works. > Would appreciate, if he can share whatever info he was referring too. Msg > being copied to VINCENT CHONG for help. > > What is meant by wrong idb state? I see this in debug event output > > Following is the interface & debug events output. > > 2504#show ip int brief > Interface IP-Address OK? Method Status > Protocol > BRI0 unassigned YES NVRAM administratively down > down > BRI0:1 unassigned YES unset administratively down > down > BRI0:2 unassigned YES unset administratively down > down > Serial0192.1.1.2 YES NVRAM down > down > Serial1193.1.1.2 YES NVRAM down > down > TokenRing0 unassigned YES NVRAM initializing > down > > 00:43:02: TR0 starting. > 00:43:23: TR0 receive SRB_FREE, state=2, if_state=6 > 00:43:24: %TR-3-OPENFAIL: Unit 0, open failed: Phys. Insertion, ring > beaconing > 00:43:24: %TR-3-BADSTART: Unit 0, Start completion and wrong idb state - > state= 0 > 00:43:25: TR0: reset from 308F4F6 > 00:43:25: TR0: txtmr: 0x0, msclk: 0x27C15C, qt: 0x0 (2605400ms) > > Following is the condensed startup config output. > > R2504#show config > Using 918 out of 32762 bytes > ! > version 12.2 > no service single-slot-reload-enable > service timestamps debug uptime > service timestamps log uptime > no service password-encryption > ! > hostname R2504 > > interface TokenRing0 > no ip address > ring-speed 4 > > TX / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=8720&t=8554 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RIP Update [7:8897]
I was practicing Lab 19 from All In One Study Guide. I did the configuration exactly as stated but the RIP is not advertising. Following is the debug ip rip & config details. Hope someone can help me. 01:12:59: RIP: ignored v1 update from bad source 193.1.1.1 on Serial1 01:13:13: RIP: ignored v1 update from bad source 152.1.1.1 on Ethernet0 01:13:19: RIP: sending v1 update to 255.255.255.255 via Ethernet0 (148.1.1.1) 01:13:19: RIP: build update entries 01:13:19: network 10.0.0.0 metric 1 01:13:19: network 192.1.1.0 metric 1 01:13:19: RIP: sending v1 update to 255.255.255.255 via Loopback0 (10.1.1.1) 01:13:19: RIP: build update entries 01:13:19: network 148.1.0.0 metric 1 01:13:19: network 192.1.1.0 metric 1 01:13:19: RIP: sending v1 update to 255.255.255.255 via Serial1 (192.1.1.1) 01:13:19: RIP: build update entries 01:13:19: network 10.0.0.0 metric 1 01:13:19: network 148.1.0.0 metric 1 R 2501 interface Loopback0 ip address 10.1.1.1 255.255.255.0 interface Ethernet0 ip address 148.1.1.1 255.255.255.0 no ip route-cache no ip mroute-cache no keepalive interface Serial1 ip address 192.1.1.1 255.255.255.0 no ip route-cache no ip mroute-cache router rip network 10.0.0.0 network 148.1.0.0 network 192.1.1.0 ip kerberos source-interface any no ip classless no ip http server end R 2511 p host R2503 2003 1.1.1.1 ip host R2504 2004 1.1.1.1 ip host R2502 2002 1.1.1.1 ip host R2501 2001 1.1.1.1 interface Loopback0 ip address 1.1.1.1 255.0.0.0 - This is being used for Terminal Server interface Serial0 ip address 192.1.1.2 255.255.255.0 no fair-queue clockrate 64000 interface Serial1 ip address 193.1.1.1 255.255.255.0 no fair-queue clockrate 64000 router rip network 192.1.1.0 network 193.1.1.0 ip kerberos source-interface any no ip classless no ip http server end R 2503 interface Ethernet0 ip address 152.1.1.1 255.255.255.0 no keepalive interface Serial0 ip address 193.1.1.2 255.255.255.0 no ip mroute-cache no ip address router rip network 152.1.0.0 network 193.1.1.0 ip kerberos source-interface any no ip classless no ip http server end TIA / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=8897&t=8897 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: RIP Update [7:8897]
Thanks Circusnuts. Problem solved. The interface connection was wrong between the routers. By the way can someone clarify on this one - Is it wrong to connect Serial 0 of Router A to Serial 1 of Router B. I did come across this problem while playing on my home lab with rip configuration. Tx / RamG ""Circusnuts"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Are you taking into account RIP v1 assumes the only viable subnet mask is > the one on the interface it advertises out of ??? Are you summarizing & > does it follow the natural bit boundaries (so as not to advertise a > blackhole). > > Am I close to the issue ??? > > Phil > - Original Message - > From: RamG > To: > Sent: Sunday, June 17, 2001 3:20 PM > Subject: RIP Update [7:8897] > > > > I was practicing Lab 19 from All In One Study Guide. I did the > > configuration exactly as stated but the RIP is not advertising. Following > > is the debug ip rip & config details. Hope someone can help me. > > > > 01:12:59: RIP: ignored v1 update from bad source 193.1.1.1 on Serial1 > > 01:13:13: RIP: ignored v1 update from bad source 152.1.1.1 on Ethernet0 > > 01:13:19: RIP: sending v1 update to 255.255.255.255 via Ethernet0 > > (148.1.1.1) > > 01:13:19: RIP: build update entries > > 01:13:19: network 10.0.0.0 metric 1 > > 01:13:19: network 192.1.1.0 metric 1 > > 01:13:19: RIP: sending v1 update to 255.255.255.255 via Loopback0 > (10.1.1.1) > > 01:13:19: RIP: build update entries > > 01:13:19: network 148.1.0.0 metric 1 > > 01:13:19: network 192.1.1.0 metric 1 > > 01:13:19: RIP: sending v1 update to 255.255.255.255 via Serial1 > (192.1.1.1) > > 01:13:19: RIP: build update entries > > 01:13:19: network 10.0.0.0 metric 1 > > 01:13:19: network 148.1.0.0 metric 1 > > > > R 2501 > > > > interface Loopback0 > > ip address 10.1.1.1 255.255.255.0 > > interface Ethernet0 > > ip address 148.1.1.1 255.255.255.0 > > no ip route-cache > > no ip mroute-cache > > no keepalive > > interface Serial1 > > ip address 192.1.1.1 255.255.255.0 > > no ip route-cache > > no ip mroute-cache > > router rip > > network 10.0.0.0 > > network 148.1.0.0 > > network 192.1.1.0 > > ip kerberos source-interface any > > no ip classless > > no ip http server > > end > > > > R 2511 > > > > p host R2503 2003 1.1.1.1 > > ip host R2504 2004 1.1.1.1 > > ip host R2502 2002 1.1.1.1 > > ip host R2501 2001 1.1.1.1 > > interface Loopback0 > > ip address 1.1.1.1 255.0.0.0 - This is being used for Terminal Server > > interface Serial0 > > ip address 192.1.1.2 255.255.255.0 > > no fair-queue > > clockrate 64000 > > interface Serial1 > > ip address 193.1.1.1 255.255.255.0 > > no fair-queue > > clockrate 64000 > > router rip > > network 192.1.1.0 > > network 193.1.1.0 > > ip kerberos source-interface any > > no ip classless > > no ip http server > > end > > > > R 2503 > > > > interface Ethernet0 > > ip address 152.1.1.1 255.255.255.0 > > no keepalive > > interface Serial0 > > ip address 193.1.1.2 255.255.255.0 > > no ip mroute-cache > > no ip address > > router rip > > network 152.1.0.0 > > network 193.1.1.0 > > ip kerberos source-interface any > > no ip classless > > no ip http server > > end > > > > TIA / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=8903&t=8897 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: RIP Update [7:8897]
Thanks John. Y'day night I played around by connecting the interface vice versa. It works. You are correct. I have noted your clockrate comment which I will implement when I purchase 2522. RamG ""John Neiberger"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > It does not matter which serial interfaces you use, so you should have > no problem connecting Serial 0 on one router to Serial 1 on another > router. There is one caveat, though. Usually the first two serial > interfaces are high-speed and the rest are low speed. If you connected > Serial 0 to Serial 2 and tried to run at T-1 speeds it would fail. The > low speed ports aren't capable of clockrates higher than 115k. > > Regards, > John > > >>> "RamG" 6/17/01 5:02:39 PM >>> > Thanks Circusnuts. Problem solved. The interface connection was > wrong > between the routers. > > By the way can someone clarify on this one - Is it wrong to connect > Serial 0 > of Router A to Serial 1 of Router B. I did come across this problem > while > playing on my home lab with rip configuration. > > Tx / RamG > > ""Circusnuts"" wrote in message > [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > > Are you taking into account RIP v1 assumes the only viable subnet > mask is > > the one on the interface it advertises out of ??? Are you > summarizing & > > does it follow the natural bit boundaries (so as not to advertise a > > blackhole). > > > > Am I close to the issue ??? > > > > Phil > > - Original Message - > > From: RamG > > To: > > Sent: Sunday, June 17, 2001 3:20 PM > > Subject: RIP Update [7:8897] > > > > > > > I was practicing Lab 19 from All In One Study Guide. I did the > > > configuration exactly as stated but the RIP is not advertising. > Following > > > is the debug ip rip & config details. Hope someone can help me. > > > > > > 01:12:59: RIP: ignored v1 update from bad source 193.1.1.1 on > Serial1 > > > 01:13:13: RIP: ignored v1 update from bad source 152.1.1.1 on > Ethernet0 > > > 01:13:19: RIP: sending v1 update to 255.255.255.255 via Ethernet0 > > > (148.1.1.1) > > > 01:13:19: RIP: build update entries > > > 01:13:19: network 10.0.0.0 metric 1 > > > 01:13:19: network 192.1.1.0 metric 1 > > > 01:13:19: RIP: sending v1 update to 255.255.255.255 via Loopback0 > > (10.1.1.1) > > > 01:13:19: RIP: build update entries > > > 01:13:19: network 148.1.0.0 metric 1 > > > 01:13:19: network 192.1.1.0 metric 1 > > > 01:13:19: RIP: sending v1 update to 255.255.255.255 via Serial1 > > (192.1.1.1) > > > 01:13:19: RIP: build update entries > > > 01:13:19: network 10.0.0.0 metric 1 > > > 01:13:19: network 148.1.0.0 metric 1 > > > > > > R 2501 > > > > > > interface Loopback0 > > > ip address 10.1.1.1 255.255.255.0 > > > interface Ethernet0 > > > ip address 148.1.1.1 255.255.255.0 > > > no ip route-cache > > > no ip mroute-cache > > > no keepalive > > > interface Serial1 > > > ip address 192.1.1.1 255.255.255.0 > > > no ip route-cache > > > no ip mroute-cache > > > router rip > > > network 10.0.0.0 > > > network 148.1.0.0 > > > network 192.1.1.0 > > > ip kerberos source-interface any > > > no ip classless > > > no ip http server > > > end > > > > > > R 2511 > > > > > > p host R2503 2003 1.1.1.1 > > > ip host R2504 2004 1.1.1.1 > > > ip host R2502 2002 1.1.1.1 > > > ip host R2501 2001 1.1.1.1 > > > interface Loopback0 > > > ip address 1.1.1.1 255.0.0.0 - This is being used for Terminal > Server > > > interface Serial0 > > > ip address 192.1.1.2 255.255.255.0 > > > no fair-queue > > > clockrate 64000 > > > interface Serial1 > > > ip address 193.1.1.1 255.255.255.0 > > > no fair-queue > > > clockrate 64000 > > > router rip > > > network 192.1.1.0 > > > network 193.1.1.0 > > > ip kerberos source-interface any > > > no ip classless > > > no ip http server > > > end > > > > > > R 2503 > > > > > > interface Ethernet0 > > > ip address 152.1.1.1 255.255.255.0 > > > no keepalive > > > interface Serial0 > > > ip address 193.1.1.2 255.255.255.0 > > > no ip mroute-cache > > > no ip address > > > router rip > > > network 152.1.0.0 > > > network 193.1.1.0 > > > ip kerberos source-interface any > > > no ip classless > > > no ip http server > > > end > > > > > > TIA / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=8952&t=8897 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Accessories for sale [7:9510]
I have following items for sale. a) 4 Pairs of Rack Mount Kit - 2500 series - USD.7 Each b) Two 4MB Flash Intel - 2500 series - USD.20 Each c) 4 Black Box Media Filters - USD.6 Each d) 1 Type 3 Media Filter - USD.6 e) 4 LAN UPT Cat 5 Patch Cable - USD.2 Each If it interests anybody contact me directly. Pls note shipping will be extra. TX / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=9510&t=9510 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Five-in-one synchronous serial [7:10312]
Can we not use 2523 which also has 10 serial ports like 2522. I am planning to buy 2523 to connect 2501/02/03/04 & 2511 serial ports to 2523 using DTE/DCE cables. Would that be possible or not. Any comments from the group would be appreciated. Tx / RamG ""Ole Drews Jensen"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > I am looking for a router with 3 or more synchronous serial ports for my > lab, but all the fixed 2500 models only have a max of two. > > I can see that you can get a five-in-one synchronous serial WAN interface > card for the 2524 and 2525, but does that mean that I can connect five > different 2501's (to take an example) to this one port with a special cable? > > Also, would that be the best and/or cheapest solution, or can some of you > with labs at home throw me a good idea what to look for? > > I need the same kind of synchronous DB60 serial ports as my 2501's/2502's > have. > > Thanks, > > Ole > > ~~~ > Ole Drews Jensen > Systems Network Manager > CCNA, MCSE, MCP+I > RWR Enterprises, Inc. > [EMAIL PROTECTED] > ~~~ > http://www.OleDrews.com/CCNP > ~~~ > NEED A JOB ??? > http://www.oledrews.com/job > ~~~ Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=10339&t=10312 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: price of 2514 [7:10776]
C - Do you have any 2523 or 2521. What's the price? I am from Toronto/Canada. Tx / RamG ""Cisco Nuts"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Hi Charles, > If you want one for $700.00 + $20.00 s/h, please contact me. > Kind regards. > > BTW: I also have a bunch of other routers including a 2511 at great > reasonable prices. > > > >From: "Circusnuts" > >Reply-To: "Circusnuts" > >To: [EMAIL PROTECTED] > >Subject: Re: price of 2514 [7:10776] > >Date: Tue, 3 Jul 2001 08:46:43 -0400 > > > >Just about anyone on Ebay would sell for $700. A lot of the sought after > >25xx are $500 & below @ this point. The prices will return come to cooler > >weather... > > > >Phil > > > >- Original Message - > >From: "Charles Peter" > >To: > >Sent: Tuesday, July 03, 2001 3:53 AM > >Subject: OT : price of 2514 [7:10776] > > > > > > > I saw a post days ago saying that a 2514 (used one) costs around US$700. > > > Could you please let me know which vendor sell at this price ? > > > > >_ > > > Get Your Private, Free E-mail from MSN Hotmail at > >http://www.hotmail.com. > _ > Get your FREE download of MSN Explorer at http://explorer.msn.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=10932&t=10776 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
MAU & Flash for sale [7:11337]
Hello Friends, Following are for sale. Interested people can contact me directly. ONE Andrew 8228 MAU- 8 Port FOUR db9 - rj45 Media Filter (Black Box) TWO 4MB Flash - Intel - 2500 Series SIX Cat5 Patch Cables I don't need any of these items. So quote your best offer. I will get rid of everything. Tx / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=11337&t=11337 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Accessories for sale [7:9510]
Message addressed to Mr. Mark Rose Pls watch your mail for refund towards two mismatch rack mount sold. Tx / RamG ""RamG"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > I have following items for sale. > > a) 4 Pairs of Rack Mount Kit - 2500 series - USD.7 Each > > b) Two 4MB Flash Intel - 2500 series - USD.20 Each > > c) 4 Black Box Media Filters - USD.6 Each > > d) 1 Type 3 Media Filter - USD.6 > > e) 4 LAN UPT Cat 5 Patch Cable - USD.2 Each > > If it interests anybody contact me directly. Pls note shipping will be > extra. > > TX / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=12474&t=9510 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Your advise pls! [7:60327]
Hello Group, I finished NP/DA in Oct 2000. Since then, I have been looking for job in networking. I know my drawback for being unsuccessful. It is my past experience {as Accountant} and real world experience with Cisco routers. In order to get some experience, I had setup 5 router home lab and gained little experience by practicing / solving lab exercise from Satterlee book. Even that did not help me to get entry level positions. The job market in Toronto is so bad that, I am unable to find Tech support job too. Now it is time for me to recertify {Oct}. What should, I do? I have already spent a lot of money on books/routers. I cannot spend any more on books/routers. Any advise appreciated. / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=60327&t=60327 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Your advise pls! [7:60327]
Thanks to the advise of Mr. Howard & Mr.Kaminski. My recertification date are due at end of this year. Since the IT market all over the globe is very bad and it is my feeling it will take a while till 2004 to stabilize. As a result, I have decided to spend valuable time preparing for Nov 2003 CPA. Trying to upgrade my skill depending on the market requirement. That does not mean, I will give up my cisco recertification. I will eventually recertify and will keep looking for entry level opening within Toronto. I still have my home lab to play around which does not meet the current CCIE lab specification, however, good the NP/DA recertification. Tx / RamG Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=60723&t=60327 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: OT: Where are the networking jobs? (was: question [7:48701]
Hello, I have been looking for junior to entry level position in Middle East for quite a while. Would appreciate, if you can share any links. Tx / RamG ""Shaheen Gagan"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Saudi Arabia would be a good place to start. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=48818&t=48701 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: CCNP dumps????????????? [7:55156]
I completely agree with Mark. Erwin do not refer your comments towards a country. Raju is my country men and I will not tolerate any one on the list bashing the country for his dump request. Tx / RamG ""Vinod Raju"" wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... > Could someone please tell me where to avail latest CCNP dumps especially for > BSCI (routing) and BSCSN (switching)? > > Please reply fast > > Thanx in advance, > > Raj Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=55180&t=55156 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]