Congigure the ATM LS 100 ! [7:63328]
Hi all, Does anyone know how to configure the LightStream LS 100 switch to work between 2 7200 routers with ATM interfaces? I am trying to set up the ATM lab practice but can't get the switch to pass traffic between 2 routers? Any help would be much appreciated. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=63328&t=63328 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Voice Over ATM for ccbootcamp lab. [7:64118]
Hi I need help on this particular problem. Here is the issue: I have 2 3620 with Voice Module intstalled in each router, but no ATM Module. I also have 2 7206 with ATM modules installed in each router but no Voice Module! The question is how am I going to do the Voice Over ATM lab without having to buy either the voice modules for the 72xx routers or ATM modules for the 36xx routers? Are there any voice modules made for the 72xx routers? Any suggestion is much appreciated. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64118&t=64118 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Router 2500 series crashed in BGP!!! [7:64554]
Hi, I have experienced the Cisco 25xx routers crashed many time when configuring BGP with the 26xx and 36xx routers, connected in a lab environment; most of time happened when I do the "clear ip bgp *" command. Does anyone have the same problem? The 25xx routers have 16RAM and 16 FLASH installed. Any suggestion to fix this problem is very much appreciated. Thanks, Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64554&t=64554 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
mpls, QoS, etc... [7:64810]
Hi All, Can anyone show me a few links to some good QoS, MPLS practice labs? Thanks in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=64810&t=64810 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
PROBLEM WITH ATM LABS, LS100 + 3 72XX ATM ROUTERS!! [7:65026]
Hi All, I've been trying to work on this particular ATM lab and unable to make the routers connect to each other via a LS100 LightStream Switch!! Could anyone with help me to solve this problem? Below is the configurartion, debug output of the three ATM routers and the LS100 switch: Here are the configuration of the 3 ATM routers connect to slot 0, 1, 2 of the LS100: RouterA# show run ! interface ATM5/0 no ip address atm pvc 1 0 5 qsaal no atm ilmi-keepalive ! interface ATM5/0.2 multipoint ip address 138.108.168.1 255.255.255.0 atm nsap-address 47..0001.00 atm arp-server nsap 47..0002.00 ! interface Serial6/0 no ip address shutdown serial restart-delay 0 RouterB# show run interface ATM1/0 no ip address atm pvc 1 0 5 qsaal no atm ilmi-keepalive ! interface ATM1/0.2 multipoint ip address 138.108.168.2 255.255.255.0 atm nsap-address 47..0002.00 atm arp-server self ! RouterC# ! interface ATM1/0 no ip address atm pvc 1 0 5 qsaal no atm ilmi-keepalive ! interface ATM1/0.1 multipoint ip address 138.108.168.3 255.255.255.0 atm nsap-address 47..0003.00 atm arp-server nsap 47..0002.00 ! interface FastEthernet2/0 no ip address shutdown duplex half ! LS10# SHOW ROUTE Destination Type PrimaryVPI Secondary VPI 47 00 00 000100 NSAP * 0 -- - 47 00 00 000200 NSAP * 2 -- - 47 00 00 000300 NSAP * 3 -- - LS10#SHOW ATMSIG Line U/N T303 T308 T309 T310 T313 T316 T317 T322 T398 T399 UNIver VPI 0 Network4 30 90 104 120 6044 143.0 0 1 Network4 30 90 104 120 6044 143.0 0 2 Network4 30 90 104 120 6044 143.0 0 3 Network4 30 90 104 120 6044 143.0 0 Debug output from routerA: RouterA#debug atm sig-all routerA#debug atm sig-all ATM Signalling Events debugging is on ATM Signalling Error debugging is on ATM Signalling IE debugging is on ATM Signalling Api debugging is on routerA#ping 138.108.168.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 138.108.168.2, timeout is 2 seconds: 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:0) API - alloc_connection_id 2E 00:42:08: ATMAPI: (c->s): SETUPv2 ci: 0x2E mp: 0 ei: 0x 00:42:08: ATMSIG: Called len 20 00:42:08: ATMSIG: Calling len 20 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:0) build Setup msg, Null(U0) stat e 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:0) API - from sig-client ATM_OWNE R_SMAP 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:47) Input event : Req Setup in Nu ll(U0) 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:47) Output Setup msg(XferAndTx), Null(U0) state 00:42:08: ATMSIG: Called Party Addr: 47..000 2.00 00:42:08: ATMSIG: Calling Party Addr: 47..000 1.00 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:47) Null(U0) -> Call Initiated(U1 ) 00:42:08: E164 NOT Converted 00:42:08: ATMSIG(ATM5/0 0,0 - 0046/00): (vcnum:47) Input event : Rcvd Call Proce eding in Call Initiated(U1) 00:42:08: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Connection Identifier IE: associated sig = 88 vpi = 0 vci = 128 00:42:08: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Call Initiated(U1) -> Outgo ing Call Proceeding(U3) 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Input event : Rcvd Release in Outgoing Call Proceeding(U3) 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47)cause = Invalid, location = User 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Outgoing Call Proceeding(U3 ) -> Release Indication(U12) 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) API - notifying Release eve nt to client ATM5/0.2 00:42:16: ATMAPI: (cs): RELEASE_COMPv2 ci: 0x2E cause: 0x0 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) API - from sig-client ATM_O WNER_SMAP 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Input event : Req Release C omplete in Release Indication(U12) 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) building cause code - cause = (0x1B)destination out of order, IE_cause = (0x1B)destination out of order, lo cation = User 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Output Release Complete msg , Release Indication(U12) state 00:42:16: ATMSIG(ATM5/0 0,128 - 0046/00): (vcnum:47) Release Indication(U12) -> Dead 00:42:16: ATMSIG(ATM5/0 0,0 - 0047/00): (vcnum:0) API - alloc_connection_id 2F 00:42:16: ATMAPI: (c->s): SETUPv2 ci: 0x2F mp: 0 ei: 0x 00:42:16: ATMSIG: Called len 20 00:42:16: ATMSIG: Calling len 20 00:42:16: ATMSIG(ATM5/0 0,0 - 0047/00): (vcnum:0) build Setup msg, Null(U0) stat e 00:42:16: ATMSIG(ATM5/0 0,0 - 0047/
7206 encapsulation failed at every interface!!! [7:65081]
Hi All, Do anybody know why the encapsulation always failed on every type of interfaces on my 7206 router? I have replaced the I/O and the encapsulation is still FAILED!!! Below is the "debug ip packet" of the interface e1/0 pinging the default-gateway with the encapsulation FAILED and pinging itself successfully: routerB#debug ip packet IP packet debugging is on routerB#ping 192.168.0.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.0.1, timeout is 2 seconds: 00:02:31: IP: s=192.168.0.192 (local), d=192.168.0.1, len 100, cef process switc hed 00:02:31: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, sen ding 00:02:31: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, enc apsulation failed. 00:02:33: IP: s=192.168.0.192 (local), d=192.168.0.1, len 100, cef process switc hed 00:02:33: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, sen ding 00:02:33: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, enc apsulation failed. 00:02:35: IP: s=192.168.0.192 (local), d=192.168.0.1, len 100, cef process switc hed 00:02:35: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, sen ding 00:02:35: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, enc apsulation failed. 00:02:37: IP: s=192.168.0.192 (local), d=192.168.0.1, len 100, cef process switc hed 00:02:37: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, sen ding 00:02:37: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, enc apsulation failed. 00:02:39: IP: s=192.168.0.192 (local), d=192.168.0.1, len 100, cef process switc hed 00:02:39: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, sen ding 00:02:39: IP: s=192.168.0.192 (local), d=192.168.0.1 (Ethernet1/0), len 100, enc apsulation failed. Success rate is 0 percent (0/5) routerB#ping 192.168.0.192 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 192.168.0.192, timeout is 2 seconds: ! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms routerB# 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 2.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192, len 100, cef process swi tched 00:02:57: IP: s=192.168.0.192 (local), d=192.168.0.192 (Ethernet1/0), len 100, s ending 00:02:57: IP: s=192.168.0.192 (Ethernet1/0), d=192.168.0.192 (Ethernet1/0), len 100, rcvd 3 routerB# routerB# I am suspecting the version of the IOS image have something to do with it but not sure. I purchase this router without IOS image and running a 12.2.10a image. Thanks in advance for all your help XL Message Pos
MII media-type connector for 72xx routers? [7:65246]
Hi Everyone, I have a 7206 with a built-in FastEthernet interface which is an MII media-type connector. What type of cable and connector do I need to convert it to a regular RJ45 connection? Thank you all, Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=65246&t=65246 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IP packets unroutable???? [7:65250]
Hello Everyone, I have this router which will give me the debug message everytime I ping a connected network: Every interfaces, ATM, FastEthernet, Serial etc are same results. Seemed like there are no arp cache for the connect interfaces, but I do not know the solution to solve this problem!!! Anyone with the same problem and solutions??? Help routerC#debug ip packet de IP packet debugging is on (detailed) routerC#ping 138.168.108.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 138.168.108.2, timeout is 2 seconds: 00:13:17: IP: s=138.108.168.3 (local), d=138.168.108.2, len 100, unroutable 00:13:17: ICMP type=8, code=0. 00:13:19: IP: s=138.108.168.3 (local), d=138.168.108.2, len 100, unroutable 00:13:19: ICMP type=8, code=0. 00:13:21: IP: s=138.108.168.3 (local), d=138.168.108.2, len 100, unroutable 00:13:21: ICMP type=8, code=0. 00:13:23: IP: s=138.108.168.3 (local), d=138.168.108.2, len 100, unroutable 00:13:23: ICMP type=8, code=0. 00:13:25: IP: s=138.108.168.3 (local), d=138.168.108.2, len 100, unroutable 00:13:25: ICMP type=8, code=0. Success rate is 0 percent (0/5) routerC# Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=65250&t=65250 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
ATM LS100 PROBLEM! [7:65585]
Hi all, I have an LS100 ATM LIGHTSTREAM (NOT LS1010) in between 2 ATM routers configured as follow: interface ATM2/0 ip address 10.1.1.2 255.255.255.0 ip ospf network point-to-multipoint map-group atm atm pvc 1 0 16 ilmi atm pvc 2 2 48 aal5snap no atm ilmi-keepalive map-list atm ip 10.1.1.1 atm-vc 2 broadcast ATM SWITCH LS100 IN BETWEEN interface ATM2/0 ip address 10.1.1.1 255.255.255.0 ip ospf network point-to-multipoint map-group atm atm pvc 1 0 16 ilmi atm pvc 2 2 49 aal5snap no atm ilmi-keepalive map-list atm ip 10.1.1.2 atm-vc 2 broadcast ! I don't know how to configure the LS100 LIGHTSTREAM SWITCH to connect the 2 routers. Can someone with the experience of LS100 send me a configuration of this switch? Thank you all in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=65585&t=65585 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
7206 PROBLEM! [7:65950]
Dear All member, Does anyone know how the procedure of how to recover a BOOTLDR image for a cisco 7206 router? When I boot this router up, it did not see the boot image and reboot with image store in flash card. Thanks you all in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=65950&t=65950 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Problem with 7206 router [7:66036]
Hi everyone, I have a very unique problem with this particular 7206 which I can't solve it for the last 2 weeks!!! I can only ping the local interfaces of this router but it won't communicate with any other routers connected to it!!! The "show ip interface atm2/0" output show that the broadcast address is 255.255.255.255 and determined by setup, while other routers connect to it all stated that: Address determined by non-volatile memory. Here are the examples of the 2 ATM interfaces' output "show ip int" connected via an ATM switch: r9#sh ip int atm1/0 ATM1/0 is up, line protocol is up Internet address is 10.1.1.1/24 Broadcast address is 255.255.255.255 Address determined by non-volatile memory (THIS ROUTER WOULD WORK) MTU is 4470 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP CEF switching is enabled IP Fast switching turbo vector IP Normal CEF switching turbo vector IP multicast fast switching is enabled r9# R3#sh ip int atm2/0 ATM2/0 is up, line protocol is up Internet address is 10.1.1.2/24 Broadcast address is 255.255.255.255 Address determined by setup command (THIS ROUTER WILL FAIL) MTU is 4470 bytes Helper address is not set Directed broadcast forwarding is disabled Multicast reserved groups joined: 224.0.0.5 224.0.0.6 Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is disabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP Fast switching turbo vector IP Null turbo vector IP multicast fast switching is disabled IP multicast distributed fast switching is disabled IP route-cache flags are None Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Probe proxy name replies are disabled Policy routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled R3# Any member with experience on this particular problem or any idea will help tremendously, and I thank you all in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66036&t=66036 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
type 4 LSA updates OSPF question [7:66089]
Hi everyone, Can someone tell me that only ABR will ORIGINATE type 4 LSA in OSPF or both ABR and ASBR do? Thanks Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66089&t=66089 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Router ID? [7:66108]
Hi all, Two routing protocols: OSPF and EIGRP DO need to have their own router ID reachable by other routers to have proper network connectivity, or am I incorrect? Any confirmation on this is much appreciated. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66108&t=66108 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
EIGRP SUMMARY ROUTE METRIC [7:66344]
Hi, I have a question that need to be clarified regarding the metric of EIGRP summary metric: The metric of EIGRP summarized route derived from the component route that has the biggest or smallest metric? Any clarification on this matter is much appreciated. I could not find answer in any of the Cisco Press books or any web site at all. Thanks in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66344&t=66344 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Seeking for a lab partner or groupstudy in Honolulu, Hawaii. [7:66361]
Anyone in Honolulu, Hawaii looking for a Lab partner, or interest to form a CCIE group study for the Lab Exam? Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66361&t=66361 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
CCIE written exam passed! [7:66364]
To all, I passed the CCIE written exam passed today, thanks for everybody helps! Now I need some advice of where and how to start for my Lab exam which will be schedule somewhere by October or November of 2003. Any suggestion or input regarding this matter is very much appreciated! Again, thanks to all the members this group. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66364&t=66364 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Ping fail at all interfaces! [7:66472]
I have an issue that took me almost a month and still not figure out what's the problem? I can ping out to a connected router (fastethernet or any type of interfaces) and can only ping the local interface. For example, if I connect this router FastEthernet F3/0 to another router FastEthernet 4/0. both routers' fastethernets shown UP/UP status but none can ping each other. this particular router only can ping itself and refuse to ping any other... Here is the configurations and pinging with "debug ip packet detail": Router#sh run Building configuration... Current configuration: ! version 12.0 service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname Router ! ! ! ! ! ! ip subnet-zero no ip domain-lookup ! ! ! ! ! ! ! ! interface FastEthernet0/0 no ip address no ip directed-broadcast shutdown media-type MII half-duplex ! interface TokenRing1/0 ip address 150.50.18.100 255.255.255.0 no ip directed-broadcast shutdown ring-speed 16 ! interface TokenRing1/1 no ip address no ip directed-broadcast shutdown ring-speed 16 ! interface TokenRing1/2 no ip address no ip directed-broadcast shutdown ring-speed 16 ! interface TokenRing1/3 no ip address no ip directed-broadcast shutdown ring-speed 16 ! interface ATM2/0 no ip address no ip directed-broadcast shutdown no atm ilmi-keepalive ! interface FastEthernet3/0 ip address 1.1.1.2 255.255.255.0 no ip directed-broadcast half-duplex ! ip classless no ip http server ! ! line con 0 transport input none line aux 0 line vty 0 4 login ! end Router#sh ip int f3/0 FastEthernet3/0 is up, line protocol is up Internet address is 1.1.1.2/24 Broadcast address is 255.255.255.255 Address determined by setup command MTU is 1500 bytes Helper address is not set Directed broadcast forwarding is disabled Outgoing access list is not set Inbound access list is not set Proxy ARP is enabled Security level is default Split horizon is enabled ICMP redirects are always sent ICMP unreachables are always sent ICMP mask replies are never sent IP fast switching is enabled IP fast switching on the same interface is disabled IP Flow switching is disabled IP Fast switching turbo vector IP Null turbo vector IP multicast fast switching is enabled IP multicast distributed fast switching is disabled IP route-cache flags are Fast Router Discovery is disabled IP output packet accounting is disabled IP access violation accounting is disabled TCP/IP header compression is disabled RTP/IP header compression is disabled Probe proxy name replies are disabled Policy routing is disabled Network address translation is disabled WCCP Redirect outbound is disabled WCCP Redirect exclude is disabled BGP Policy Mapping is disabled Router#ping 1.1.1.1 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.1, timeout is 2 seconds: 00:28:06: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, sending 00:28:06: ICMP type=8, code=0 00:28:06: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, encapsula tion failed 00:28:06: ICMP type=8, code=0. 00:28:08: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, sending 00:28:08: ICMP type=8, code=0 00:28:08: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, encapsula tion failed 00:28:08: ICMP type=8, code=0. 00:28:10: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, sending 00:28:10: ICMP type=8, code=0 00:28:10: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, encapsula tion failed 00:28:10: ICMP type=8, code=0. 00:28:12: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, sending 00:28:12: ICMP type=8, code=0 00:28:12: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, encapsula tion failed 00:28:12: ICMP type=8, code=0. 00:28:14: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, sending 00:28:14: ICMP type=8, code=0 00:28:14: IP: s=1.1.1.2 (local), d=1.1.1.1 (FastEthernet3/0), len 100, encapsula tion failed 00:28:14: ICMP type=8, code=0. Success rate is 0 percent (0/5) Router# Router#ping 1.1.1.2 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 1.1.1.2, timeout is 2 seconds: ! Success rate is 100 percent (5/5), round-trip min/avg/max = 1/2/4 ms Router# 00:28:34: IP: s=1.1.1.2 (local), d=1.1.1.2 (FastEthernet3/0), len 100, sending 00:28:34: ICMP type=8, code=0 00:28:34: IP: s=1.1.1.2 (FastEthernet3/0), d=1.1.1.2 (FastEthernet3/0), len 100, rcvd 3 00:28:34: ICMP type=8, code=0 00:28:34: IP: s=1.1.1.2 (local), d=1.1.1.2 (FastEthernet3/0), len 100, sending 00:28:34: ICMP type=0, code=0 00:28:34: IP: s=1.1.1.2 (FastEthernet3/0), d=1.1.1.2 (FastEthernet3/0), len 100, rcvd 3 00:28:34: ICMP type=0, code=0 00:28:34: IP: s=1.1.1.2 (local), d=1.1.1.2 (FastEthernet3/0), len 100, sending 00:28:34: ICMP type=8, code=0 00:28:34: IP: s=1.1.1.2 (FastEthernet3/0), d=
Re: Ping fail at all interfaces! [7:66472]
I have swapped the FastEthernet modules of both routers and still NO WORK If I remove the FastEthernet from the TROUBLED router and install it in another identical model router with identical IOS and both worked just fine Could be hardware problem with the chassis (it is a 7206 chassis) Thank you all xy - Original Message - From: "richard dumoulin" To: Sent: Sunday, March 30, 2003 10:43 AM Subject: Re: Ping fail at all interfaces! [7:66472] > To me everything seems well configured plus Xy says he has been > troubleshooting for one month now. > I would suggest that you upgrade the IOS on this particular router. > > Also, does it happens the same if you ping from the other router ? > > Regards. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=66515&t=66472 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
HELP ON THE 3550 SWITCH [7:70892]
I have this problem with this CS-C3550-24PWR-SMI Here is what happened: I tried to upgrade this switch to EMI image: c3550-i5q3l2-mz.121-11.EA1.bin. After loading the new EMI image I then issue the command: boot system flash:c3550-i5q3l2-mz.121-11.EA1.bin. When reboot after upgrading, it keep recycling the booting process as shown below: Loading "flash:c3550-i5q3l2-mz.121-11.EA1.bin"...### # ### # ### # ### # ### # # File "flash:c3550-i5q3l2-mz.121-11.EA1.bin" uncompressed and installed, entry po int: 0x3000 executing... Error: hardware not supported by firmware. Try loading newer software instead. System Resetting... Evidently, the switch allowed me to upgrade with this EMI image but not compatible. I have upgraded several of the regular 3550s in the pass without any problem, I think this particular switch with the PWR suffix has something to do with this problem. Any one know how to reverse this mistake or setting this switch to boot with the original IOS which still install in the flash. Any input to resolve this problem is very much appreciated. Thank you all in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=70892&t=70892 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
HELP ON THE CS-C3550-24PWR-SMI [7:70893]
Hi all, I have this problem with this CS-C3550-24PWR-SMI Here is what happened: I tried to upgrade this switch to EMI image: c3550-i5q3l2-mz.121-11.EA1.bin. After loading the new EMI image I then issue the command: boot system flash:c3550-i5q3l2-mz.121-11.EA1.bin. When reboot after upgrading, it keep recycling the booting process as shown below: Loading "flash:c3550-i5q3l2-mz.121-11.EA1.bin"...### # ### # ### # ### # ### # # File "flash:c3550-i5q3l2-mz.121-11.EA1.bin" uncompressed and installed, entry po int: 0x3000 executing... Error: hardware not supported by firmware. Try loading newer software instead. System Resetting... Evidently, the switch allowed me to upgrade with this EMI image but not compatible. I have upgraded several of the regular 3550s in the pass without any problem, I think this particular switch with the PWR suffix has something to do with this problem. Any one know how to reverse this mistake or setting this switch to boot with the original IOS which still install in the flash. Any input to resolve this problem is very much appreciated. Thank you all in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=70893&t=70893 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Content Engine CE-505 [7:71313]
Hi, Does anyone know the procedure of how to recover a corrupted software of a Content Engine CE-505? Any help or link is very much appreciated. Thanks in advance. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=71313&t=71313 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: how about ccie salary in US? [7:71143]
dear n rf, area you still in networking business, and are you a CCIE? Just curious :) Xy - Original Message - From: "n rf" To: Sent: Tuesday, June 24, 2003 4:46 PM Subject: RE: how about ccie salary in US? [7:71143] > douglas mizell wrote: > > not. I honestly cannot comment on the job market at home except > > to say it > > sounds dismal, if there really are CCIE's out there fighting > > over $35K jobs > > than to hell with this whole idea, open a taco stand. > > > > Which is why a growing number of them are leaving the industry. Without > naming names (I want to respect their privacy), I can now count in double > figures the number of CCIE's who have left the field for othe work. Some > have gone back to being UNIX admins, which is what they had been doing > before they got into networks. Some are in graduate school. Some have > finished graduate school and are in entirely different fields - strategy > consulting, Wall Street, etc. I know one who became a real-estate agent. > > Invariably they all say the same thing, which is that while networks are > interesting, they gotta do what they gotta do to pay the bills, and if > networks aren't going to butter their bread, they have to find something > that will. And in some cases, they butter their bread with Lurpak. The guy > who's a real-estate agent now makes several times more than he ever made as > a network guy even during the dotcom boom. Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=71329&t=71143 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
password recovery for ATM Light Stream LS 100 [7:61838]
Does any one know the procedure of how to do the password recovery for an ATM LightStream LS 100? Any help is appreciated. Can't find any link on CCO. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61838&t=61838 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
password recovery for ATM Light Stream LS 100 [7:61837]
Does any one know the procedure of how to do the password recovery for an ATM LightStream LS 100? Any help is appreciated. Can't find any link on CCO. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=61837&t=61837 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
flow timer [7:62294]
Hello everyone, Could someone explain to me what the heck is "flow timer"? Thanks, Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=62294&t=62294 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
problem with 7206 router. [7:72177]
Hi everyone, I bought a 7206 router and it booted up as follow before booting by the Flash Card contains IOS. I think the internal flash device is missing or corrupted. Anyone have any sugestion how I can fix this? Here is the boot up output: System Bootstrap, Version 11.1(5) [mkamson 5], RELEASE SOFTWARE (fc1) Copyright (c) 1994 by cisco Systems, Inc. C7200 processor with 65536 Kbytes of main memory monlib does not contain a valid magic number boot: cannot open "bootflash:" an alternate boot helper program is not specified (monitor variable "BOOTLDR" is not set) and unable to determine first file in bootflash loadprog: error - on file open boot: cannot load "cisco2-C7200" And it will booted with the image installed in the Flash Card... Any sugestion is much apreciated. Xy Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=72177&t=72177 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
