RE: Cat 2950-24 [7:37374]
to all who helped me , thanks allot I enabled the portfast and it works , my customer was very happy from me , I told him about you people but he could not imagine that I got the solution from a study group , thanks again -Original Message- From: Larry Letterman [mailto:[EMAIL PROTECTED]] Sent: Thursday, March 07, 2002 5:10 AM To: [EMAIL PROTECTED] Subject: RE: Cat 2950-24 [7:37374] Portfast does not disable spanning tree, it allows the port to go into forwarding a lot faster than the usual 50-70 seconds. WE run portfast on all our production switches and it will still disable a port if a loop is detected. It should only be used for host on the network, since other switch type devices have a better chance to cause a broadcast storm with port fast turned on. Larry Letterman Cisco Systems [EMAIL PROTECTED] -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Elijah Savage Sent: Wednesday, March 06, 2002 7:57 AM To: [EMAIL PROTECTED] Subject: RE: Cat 2950-24 [7:37374] >From my knowledge if you use this command (spanning-tree portfast) on a switch port it actually disable spanning tree for that port you should only do this if pc's are connected. So if you enable portfast you disable spanning tree for that port, if you disable portfast you enable spanning tree for that port. What this does with it enabled and a pc connected to it, it will keep the port from going through all the spanning tree phases you know like learning, listening, blocking etc it will take the switch 60 seconds to figure all this out before it starts passing traffic to that port. If portfast is enabled then it does not go through those phases and will only take approximately 3 seconds before traffic is passing according to Cisco. Someone please correct me if I am wrong here or missed something. Hope that helps www.digitalrage.org latest in Technical News and HowTo's www.digitalrage.org/phpBB Discussion Forums -Original Message- From: Cebuano [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 7:21 AM To: [EMAIL PROTECTED] Subject: Re: Cat 2950-24 [7:37374] You don't disable STP on the port to the PC because STP is only run between Layer2 devices. I believe you are referring to PortFast. Elmer - Original Message - From: "Brian" To: Sent: Wednesday, March 06, 2002 2:34 AM Subject: Re: Cat 2950-24 [7:37374] > If you connect a computer to a switch port, it takes spanning tree a bit to > allow traffic to pass. If this is an individual host being connected, you > could try disabling spanning tree on the port.. > > Bri > > - Original Message - > From: "Ismail Al-Shelh" > To: > Sent: Tuesday, March 05, 2002 10:44 PM > Subject: Cat 2950-24 [7:37374] > > > > Dear all > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed > > with Dos 6.22 Operating System. We used to connect this to our 3com > > Switch1100 with the dos driver provided by 3Com. The sequence of loading > > the 3com driver to connect to 3com Switch1100 is as follows: > > LSL.COM > > 3C90X.EXE > > IPXODI.COM > > NETX.EXE > > F: > > LOGIN > > This is in a batch file and when we run the batch file it will connect > > immediately. > > The problem I am facing while connect to CISCO CATALYST 2950-24 port is > that > > If I am > > running the same batch file it will not connect. > > I have to load the LSL.COM first and port on switch to which this computer > > is connected will be in Green color. But When > > I will load 3c90x.exe immediately the port on the switch color becomes > > amber. > > I have to wait for 1 to 1.5 minutes for the port color to become green > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > I can see this because I am sitting in front of the Cisco Switch. In > actual > > the end user will run the batch file sitting somewhere in his room and he > > will get a message "Novell Netware Server not > > Found". > > Why this delay in connecting to Novell Netware through Cisco Switch. The > > same > > delay is not happening while we are connecting to 3Com Switch. > > We need you help and guidance to sort out this problem. > > Ismail Al-shelh > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37716&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cat 2950-24 [7:37374]
Moreover, the 6509 complains (cat-os) if it hears BPDU's on a port configured for Portfast . That port is automatically, immediately disabled. Joseph Brunner ASN 21572 MortgageIT MITLending New York, NY 10038 (212) 651 - 7695 Voice (212) 651 - 7795 Fax -Original Message- From: Mike Mandulak [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 9:11 PM To: [EMAIL PROTECTED] Subject: Re: Cat 2950-24 [7:37374] The portfast command does not turn STP off. The following is from CCO: Cisco added a feature named "portfast" or "fast-start," which means the STP for this port will assume that the port is not part of a loop and will immediately move to the forwarding state, without going through the blocking, listening, or learning states. This command does not turn STP off. It just makes STP skip a few (unnecessary in this circumstance) steps in the beginning on the selected port. Note: The portfast feature should never be used on switch ports that connect to other switches, hubs, or routers. These connections may cause physical loops and it is very important that spanning tree go through the full initialization procedure in these situations. A spanning tree loop can bring your network down. If portfast is turned on for a port that is part of a physical loop, it can cause a window of time where packets could possibly be continuously forwarded (and even multiply) in such a way that the network cannot recover. - Original Message - From: "Elijah Savage" To: Sent: Wednesday, March 06, 2002 10:56 AM Subject: RE: Cat 2950-24 [7:37374] > From my knowledge if you use this command (spanning-tree portfast) on a > switch port it actually disable spanning tree for that port you should > only do this if pc's are connected. So if you enable portfast you > disable spanning tree for that port, if you disable portfast you enable > spanning tree for that port. > > What this does with it enabled and a pc connected to it, it will keep > the port from going through all the spanning tree phases you know like > learning, listening, blocking etc it will take the switch 60 seconds to > figure all this out before it starts passing traffic to that port. If > portfast is enabled then it does not go through those phases and will > only take approximately 3 seconds before traffic is passing according to > Cisco. Someone please correct me if I am wrong here or missed something. > Hope that helps > > www.digitalrage.org latest in Technical News and HowTo's > www.digitalrage.org/phpBB Discussion Forums > > > -Original Message- > From: Cebuano [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 06, 2002 7:21 AM > To: [EMAIL PROTECTED] > Subject: Re: Cat 2950-24 [7:37374] > > You don't disable STP on the port to the PC because > STP is only run between Layer2 devices. > I believe you are referring to PortFast. > > Elmer > > - Original Message - > From: "Brian" > To: > Sent: Wednesday, March 06, 2002 2:34 AM > Subject: Re: Cat 2950-24 [7:37374] > > > > If you connect a computer to a switch port, it takes spanning tree a > bit > to > > allow traffic to pass. If this is an individual host being connected, > you > > could try disabling spanning tree on the port.. > > > > Bri > > > > - Original Message - > > From: "Ismail Al-Shelh" > > To: > > Sent: Tuesday, March 05, 2002 10:44 PM > > Subject: Cat 2950-24 [7:37374] > > > > > > > Dear all > > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is > installed > > > with Dos 6.22 Operating System. We used to connect this to our 3com > > > Switch1100 with the dos driver provided by 3Com. The sequence of > loading > > > the 3com driver to connect to 3com Switch1100 is as follows: > > > LSL.COM > > > 3C90X.EXE > > > IPXODI.COM > > > NETX.EXE > > > F: > > > LOGIN > > > This is in a batch file and when we run the batch file it will > connect > > > immediately. > > > The problem I am facing while connect to CISCO CATALYST 2950-24 port > is > > that > > > If I am > > > running the same batch file it will not connect. > > > I have to load the LSL.COM first and port on switch to which this > computer > > > is connected will be in Green color. But When > > > I will load 3c90x.exe immediately the port on the switch color > becomes > > > amber. > > > I have to wait for 1 to 1.5 minutes for the port color to become > green > > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > > I can see this because I am sitting in front
RE: Cat 2950-24 [7:37374]
Portfast does not disable spanning tree, it allows the port to go into forwarding a lot faster than the usual 50-70 seconds. WE run portfast on all our production switches and it will still disable a port if a loop is detected. It should only be used for host on the network, since other switch type devices have a better chance to cause a broadcast storm with port fast turned on. Larry Letterman Cisco Systems [EMAIL PROTECTED] -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Elijah Savage Sent: Wednesday, March 06, 2002 7:57 AM To: [EMAIL PROTECTED] Subject: RE: Cat 2950-24 [7:37374] >From my knowledge if you use this command (spanning-tree portfast) on a switch port it actually disable spanning tree for that port you should only do this if pc's are connected. So if you enable portfast you disable spanning tree for that port, if you disable portfast you enable spanning tree for that port. What this does with it enabled and a pc connected to it, it will keep the port from going through all the spanning tree phases you know like learning, listening, blocking etc it will take the switch 60 seconds to figure all this out before it starts passing traffic to that port. If portfast is enabled then it does not go through those phases and will only take approximately 3 seconds before traffic is passing according to Cisco. Someone please correct me if I am wrong here or missed something. Hope that helps www.digitalrage.org latest in Technical News and HowTo's www.digitalrage.org/phpBB Discussion Forums -Original Message- From: Cebuano [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 7:21 AM To: [EMAIL PROTECTED] Subject: Re: Cat 2950-24 [7:37374] You don't disable STP on the port to the PC because STP is only run between Layer2 devices. I believe you are referring to PortFast. Elmer - Original Message - From: "Brian" To: Sent: Wednesday, March 06, 2002 2:34 AM Subject: Re: Cat 2950-24 [7:37374] > If you connect a computer to a switch port, it takes spanning tree a bit to > allow traffic to pass. If this is an individual host being connected, you > could try disabling spanning tree on the port.. > > Bri > > - Original Message - > From: "Ismail Al-Shelh" > To: > Sent: Tuesday, March 05, 2002 10:44 PM > Subject: Cat 2950-24 [7:37374] > > > > Dear all > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed > > with Dos 6.22 Operating System. We used to connect this to our 3com > > Switch1100 with the dos driver provided by 3Com. The sequence of loading > > the 3com driver to connect to 3com Switch1100 is as follows: > > LSL.COM > > 3C90X.EXE > > IPXODI.COM > > NETX.EXE > > F: > > LOGIN > > This is in a batch file and when we run the batch file it will connect > > immediately. > > The problem I am facing while connect to CISCO CATALYST 2950-24 port is > that > > If I am > > running the same batch file it will not connect. > > I have to load the LSL.COM first and port on switch to which this computer > > is connected will be in Green color. But When > > I will load 3c90x.exe immediately the port on the switch color becomes > > amber. > > I have to wait for 1 to 1.5 minutes for the port color to become green > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > I can see this because I am sitting in front of the Cisco Switch. In > actual > > the end user will run the batch file sitting somewhere in his room and he > > will get a message "Novell Netware Server not > > Found". > > Why this delay in connecting to Novell Netware through Cisco Switch. The > > same > > delay is not happening while we are connecting to 3Com Switch. > > We need you help and guidance to sort out this problem. > > Ismail Al-shelh > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37423&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cat 2950-24 [7:37374]
It does not actually disable spanning tree. PortFast causes a port to enter the forwarding state immediately, bypassing the listening and learning states. Spanning tree is still enabled and able detect loops. Fears -Original Message- From: Elijah Savage [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 8:57 AM To: [EMAIL PROTECTED] Subject: RE: Cat 2950-24 [7:37374] >From my knowledge if you use this command (spanning-tree portfast) on a switch port it actually disable spanning tree for that port you should only do this if pc's are connected. So if you enable portfast you disable spanning tree for that port, if you disable portfast you enable spanning tree for that port. What this does with it enabled and a pc connected to it, it will keep the port from going through all the spanning tree phases you know like learning, listening, blocking etc it will take the switch 60 seconds to figure all this out before it starts passing traffic to that port. If portfast is enabled then it does not go through those phases and will only take approximately 3 seconds before traffic is passing according to Cisco. Someone please correct me if I am wrong here or missed something. Hope that helps www.digitalrage.org latest in Technical News and HowTo's www.digitalrage.org/phpBB Discussion Forums -Original Message- From: Cebuano [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 7:21 AM To: [EMAIL PROTECTED] Subject: Re: Cat 2950-24 [7:37374] You don't disable STP on the port to the PC because STP is only run between Layer2 devices. I believe you are referring to PortFast. Elmer - Original Message - From: "Brian" To: Sent: Wednesday, March 06, 2002 2:34 AM Subject: Re: Cat 2950-24 [7:37374] > If you connect a computer to a switch port, it takes spanning tree a bit to > allow traffic to pass. If this is an individual host being connected, you > could try disabling spanning tree on the port.. > > Bri > > - Original Message - > From: "Ismail Al-Shelh" > To: > Sent: Tuesday, March 05, 2002 10:44 PM > Subject: Cat 2950-24 [7:37374] > > > > Dear all > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed > > with Dos 6.22 Operating System. We used to connect this to our 3com > > Switch1100 with the dos driver provided by 3Com. The sequence of loading > > the 3com driver to connect to 3com Switch1100 is as follows: > > LSL.COM > > 3C90X.EXE > > IPXODI.COM > > NETX.EXE > > F: > > LOGIN > > This is in a batch file and when we run the batch file it will connect > > immediately. > > The problem I am facing while connect to CISCO CATALYST 2950-24 port is > that > > If I am > > running the same batch file it will not connect. > > I have to load the LSL.COM first and port on switch to which this computer > > is connected will be in Green color. But When > > I will load 3c90x.exe immediately the port on the switch color becomes > > amber. > > I have to wait for 1 to 1.5 minutes for the port color to become green > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > I can see this because I am sitting in front of the Cisco Switch. In > actual > > the end user will run the batch file sitting somewhere in his room and he > > will get a message "Novell Netware Server not > > Found". > > Why this delay in connecting to Novell Netware through Cisco Switch. The > > same > > delay is not happening while we are connecting to 3Com Switch. > > We need you help and guidance to sort out this problem. > > Ismail Al-shelh > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37417&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cat 2950-24 [7:37374]
Again, just a minor correction. Portfast DOES NOT disable STP on the port. It just causes the port to go from disabled to forwarding as soon as the link is sensed by the port. STP still is active on the said port. So when a loop is detected after the port is set to "forwarding", STP will change the port status to "blocking" state. Since this "portfast" works ONLY the first time the port initializes, this also proves that STP is enabled as this port will transition through the entire blocking to forwarding states when the loop disappears. Hope this clears up the topic. Elmer - Original Message - From: "Elijah Savage" To: Sent: Wednesday, March 06, 2002 10:56 AM Subject: RE: Cat 2950-24 [7:37374] > From my knowledge if you use this command (spanning-tree portfast) on a > switch port it actually disable spanning tree for that port you should > only do this if pc's are connected. So if you enable portfast you > disable spanning tree for that port, if you disable portfast you enable > spanning tree for that port. > > What this does with it enabled and a pc connected to it, it will keep > the port from going through all the spanning tree phases you know like > learning, listening, blocking etc it will take the switch 60 seconds to > figure all this out before it starts passing traffic to that port. If > portfast is enabled then it does not go through those phases and will > only take approximately 3 seconds before traffic is passing according to > Cisco. Someone please correct me if I am wrong here or missed something. > Hope that helps > > www.digitalrage.org latest in Technical News and HowTo's > www.digitalrage.org/phpBB Discussion Forums > > > -Original Message- > From: Cebuano [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 06, 2002 7:21 AM > To: [EMAIL PROTECTED] > Subject: Re: Cat 2950-24 [7:37374] > > You don't disable STP on the port to the PC because > STP is only run between Layer2 devices. > I believe you are referring to PortFast. > > Elmer > > - Original Message - > From: "Brian" > To: > Sent: Wednesday, March 06, 2002 2:34 AM > Subject: Re: Cat 2950-24 [7:37374] > > > > If you connect a computer to a switch port, it takes spanning tree a > bit > to > > allow traffic to pass. If this is an individual host being connected, > you > > could try disabling spanning tree on the port.. > > > > Bri > > > > - Original Message - > > From: "Ismail Al-Shelh" > > To: > > Sent: Tuesday, March 05, 2002 10:44 PM > > Subject: Cat 2950-24 [7:37374] > > > > > > > Dear all > > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is > installed > > > with Dos 6.22 Operating System. We used to connect this to our 3com > > > Switch1100 with the dos driver provided by 3Com. The sequence of > loading > > > the 3com driver to connect to 3com Switch1100 is as follows: > > > LSL.COM > > > 3C90X.EXE > > > IPXODI.COM > > > NETX.EXE > > > F: > > > LOGIN > > > This is in a batch file and when we run the batch file it will > connect > > > immediately. > > > The problem I am facing while connect to CISCO CATALYST 2950-24 port > is > > that > > > If I am > > > running the same batch file it will not connect. > > > I have to load the LSL.COM first and port on switch to which this > computer > > > is connected will be in Green color. But When > > > I will load 3c90x.exe immediately the port on the switch color > becomes > > > amber. > > > I have to wait for 1 to 1.5 minutes for the port color to become > green > > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > > I can see this because I am sitting in front of the Cisco Switch. > In > > actual > > > the end user will run the batch file sitting somewhere in his room > and > he > > > will get a message "Novell Netware Server not > > > Found". > > > Why this delay in connecting to Novell Netware through Cisco Switch. > The > > > same > > > delay is not happening while we are connecting to 3Com Switch. > > > We need you help and guidance to sort out this problem. > > > Ismail Al-shelh > > > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37497&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cat 2950-24 [7:37374]
The portfast command does not turn STP off. The following is from CCO: Cisco added a feature named "portfast" or "fast-start," which means the STP for this port will assume that the port is not part of a loop and will immediately move to the forwarding state, without going through the blocking, listening, or learning states. This command does not turn STP off. It just makes STP skip a few (unnecessary in this circumstance) steps in the beginning on the selected port. Note: The portfast feature should never be used on switch ports that connect to other switches, hubs, or routers. These connections may cause physical loops and it is very important that spanning tree go through the full initialization procedure in these situations. A spanning tree loop can bring your network down. If portfast is turned on for a port that is part of a physical loop, it can cause a window of time where packets could possibly be continuously forwarded (and even multiply) in such a way that the network cannot recover. - Original Message - From: "Elijah Savage" To: Sent: Wednesday, March 06, 2002 10:56 AM Subject: RE: Cat 2950-24 [7:37374] > From my knowledge if you use this command (spanning-tree portfast) on a > switch port it actually disable spanning tree for that port you should > only do this if pc's are connected. So if you enable portfast you > disable spanning tree for that port, if you disable portfast you enable > spanning tree for that port. > > What this does with it enabled and a pc connected to it, it will keep > the port from going through all the spanning tree phases you know like > learning, listening, blocking etc it will take the switch 60 seconds to > figure all this out before it starts passing traffic to that port. If > portfast is enabled then it does not go through those phases and will > only take approximately 3 seconds before traffic is passing according to > Cisco. Someone please correct me if I am wrong here or missed something. > Hope that helps > > www.digitalrage.org latest in Technical News and HowTo's > www.digitalrage.org/phpBB Discussion Forums > > > -Original Message- > From: Cebuano [mailto:[EMAIL PROTECTED]] > Sent: Wednesday, March 06, 2002 7:21 AM > To: [EMAIL PROTECTED] > Subject: Re: Cat 2950-24 [7:37374] > > You don't disable STP on the port to the PC because > STP is only run between Layer2 devices. > I believe you are referring to PortFast. > > Elmer > > - Original Message - > From: "Brian" > To: > Sent: Wednesday, March 06, 2002 2:34 AM > Subject: Re: Cat 2950-24 [7:37374] > > > > If you connect a computer to a switch port, it takes spanning tree a > bit > to > > allow traffic to pass. If this is an individual host being connected, > you > > could try disabling spanning tree on the port.. > > > > Bri > > > > - Original Message - > > From: "Ismail Al-Shelh" > > To: > > Sent: Tuesday, March 05, 2002 10:44 PM > > Subject: Cat 2950-24 [7:37374] > > > > > > > Dear all > > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is > installed > > > with Dos 6.22 Operating System. We used to connect this to our 3com > > > Switch1100 with the dos driver provided by 3Com. The sequence of > loading > > > the 3com driver to connect to 3com Switch1100 is as follows: > > > LSL.COM > > > 3C90X.EXE > > > IPXODI.COM > > > NETX.EXE > > > F: > > > LOGIN > > > This is in a batch file and when we run the batch file it will > connect > > > immediately. > > > The problem I am facing while connect to CISCO CATALYST 2950-24 port > is > > that > > > If I am > > > running the same batch file it will not connect. > > > I have to load the LSL.COM first and port on switch to which this > computer > > > is connected will be in Green color. But When > > > I will load 3c90x.exe immediately the port on the switch color > becomes > > > amber. > > > I have to wait for 1 to 1.5 minutes for the port color to become > green > > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > > I can see this because I am sitting in front of the Cisco Switch. > In > > actual > > > the end user will run the batch file sitting somewhere in his room > and > he > > > will get a message "Novell Netware Server not > > > Found". > > > Why this delay in connecting to Novell Netware through Cisco Switch. > The > > > same > > > delay is not happening while we are connecting to 3Com Switch. > > > We need you help and guidance to sort out this problem. > > > Ismail Al-shelh > > > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37431&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
OT:RE: Cat 2950-24 [7:37374]
Reminds me of a funny story about this.. I was new to Cisco eq, and switches in general. I searched and searched to find out why this was Happening to me. Finally found the answer of port fast. Was I happy ...until the next morning when The config was blank and problem was back. I put the port fast back in and all was well until the next morning. Same thing kept happening for 2 weeks. I was going nuts trying to figure out what was going on until someone Was kind enough to tell me about the mysterious command " write memory ". That fixed the problem for a week or So until one morning I get a call that nobody can log in again. I go to telnet into the switch and I cant reach it. Hm. Quick walk to the maintenance cage revealed the answer. You see this was a new enclosure that didn't have power directly to it yet, So an extension cord was run to power the 2924's. Turns out that were we plugged into was the location that the night maintenance man Also happened to plug he coffee maker into. Seems he forgot to plug it back in when he left for the night and the cabinet was dead. Since the Building Manager AND the Maintenance Manager all happened to be connected to those switches power was ran that afternoon Like I had originally requested. I bought the night guy a thing of coffee for the assistance! Thanks Larry -Original Message- From: Cebuano [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 7:21 AM To: [EMAIL PROTECTED] Subject: Re: Cat 2950-24 [7:37374] You don't disable STP on the port to the PC because STP is only run between Layer2 devices. I believe you are referring to PortFast. Elmer - Original Message - From: "Brian" To: Sent: Wednesday, March 06, 2002 2:34 AM Subject: Re: Cat 2950-24 [7:37374] > If you connect a computer to a switch port, it takes spanning tree a > bit to > allow traffic to pass. If this is an individual host being connected, > you could try disabling spanning tree on the port.. > > Bri > > - Original Message - > From: "Ismail Al-Shelh" > To: > Sent: Tuesday, March 05, 2002 10:44 PM > Subject: Cat 2950-24 [7:37374] > > > > Dear all > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is > > installed with Dos 6.22 Operating System. We used to connect this > > to our 3com Switch1100 with the dos driver provided by 3Com. The > > sequence of loading > > the 3com driver to connect to 3com Switch1100 is as follows: LSL.COM > > 3C90X.EXE > > IPXODI.COM > > NETX.EXE > > F: > > LOGIN > > This is in a batch file and when we run the batch file it will connect > > immediately. > > The problem I am facing while connect to CISCO CATALYST 2950-24 port is > that > > If I am > > running the same batch file it will not connect. > > I have to load the LSL.COM first and port on switch to which this computer > > is connected will be in Green color. But When > > I will load 3c90x.exe immediately the port on the switch color > > becomes amber. I have to wait for 1 to 1.5 minutes for the port > > color to become green and after that if load IPXODI.COM and NETX.EXE > > then it will connect. I can see this because I am sitting in front > > of the Cisco Switch. In > actual > > the end user will run the batch file sitting somewhere in his room > > and he > > will get a message "Novell Netware Server not > > Found". > > Why this delay in connecting to Novell Netware through Cisco Switch. The > > same > > delay is not happening while we are connecting to 3Com Switch. We > > need you help and guidance to sort out this problem. Ismail Al-shelh > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37485&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cat 2950-24 [7:37374]
>From my knowledge if you use this command (spanning-tree portfast) on a switch port it actually disable spanning tree for that port you should only do this if pc's are connected. So if you enable portfast you disable spanning tree for that port, if you disable portfast you enable spanning tree for that port. What this does with it enabled and a pc connected to it, it will keep the port from going through all the spanning tree phases you know like learning, listening, blocking etc it will take the switch 60 seconds to figure all this out before it starts passing traffic to that port. If portfast is enabled then it does not go through those phases and will only take approximately 3 seconds before traffic is passing according to Cisco. Someone please correct me if I am wrong here or missed something. Hope that helps www.digitalrage.org latest in Technical News and HowTo's www.digitalrage.org/phpBB Discussion Forums -Original Message- From: Cebuano [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 7:21 AM To: [EMAIL PROTECTED] Subject: Re: Cat 2950-24 [7:37374] You don't disable STP on the port to the PC because STP is only run between Layer2 devices. I believe you are referring to PortFast. Elmer - Original Message - From: "Brian" To: Sent: Wednesday, March 06, 2002 2:34 AM Subject: Re: Cat 2950-24 [7:37374] > If you connect a computer to a switch port, it takes spanning tree a bit to > allow traffic to pass. If this is an individual host being connected, you > could try disabling spanning tree on the port.. > > Bri > > - Original Message - > From: "Ismail Al-Shelh" > To: > Sent: Tuesday, March 05, 2002 10:44 PM > Subject: Cat 2950-24 [7:37374] > > > > Dear all > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed > > with Dos 6.22 Operating System. We used to connect this to our 3com > > Switch1100 with the dos driver provided by 3Com. The sequence of loading > > the 3com driver to connect to 3com Switch1100 is as follows: > > LSL.COM > > 3C90X.EXE > > IPXODI.COM > > NETX.EXE > > F: > > LOGIN > > This is in a batch file and when we run the batch file it will connect > > immediately. > > The problem I am facing while connect to CISCO CATALYST 2950-24 port is > that > > If I am > > running the same batch file it will not connect. > > I have to load the LSL.COM first and port on switch to which this computer > > is connected will be in Green color. But When > > I will load 3c90x.exe immediately the port on the switch color becomes > > amber. > > I have to wait for 1 to 1.5 minutes for the port color to become green > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > I can see this because I am sitting in front of the Cisco Switch. In > actual > > the end user will run the batch file sitting somewhere in his room and he > > will get a message "Novell Netware Server not > > Found". > > Why this delay in connecting to Novell Netware through Cisco Switch. The > > same > > delay is not happening while we are connecting to 3Com Switch. > > We need you help and guidance to sort out this problem. > > Ismail Al-shelh > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37391&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cat 2950-24 [7:37374]
Try turning spanning tree off for the port being used on the Cisco switch. Mike Dickson MCSE+Internet, MCDBA, CCNP, CCDP Dickson Network Designs voice (512)-422-3192 fax (512) 394-0320 www.dicksonnetworks.com -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Wednesday, March 06, 2002 12:45 AM To: [EMAIL PROTECTED] Subject: Cat 2950-24 [7:37374] Dear all We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed with Dos 6.22 Operating System. We used to connect this to our 3com Switch1100 with the dos driver provided by 3Com. The sequence of loading the 3com driver to connect to 3com Switch1100 is as follows: LSL.COM 3C90X.EXE IPXODI.COM NETX.EXE F: LOGIN This is in a batch file and when we run the batch file it will connect immediately. The problem I am facing while connect to CISCO CATALYST 2950-24 port is that If I am running the same batch file it will not connect. I have to load the LSL.COM first and port on switch to which this computer is connected will be in Green color. But When I will load 3c90x.exe immediately the port on the switch color becomes amber. I have to wait for 1 to 1.5 minutes for the port color to become green and after that if load IPXODI.COM and NETX.EXE then it will connect. I can see this because I am sitting in front of the Cisco Switch. In actual the end user will run the batch file sitting somewhere in his room and he will get a message "Novell Netware Server not Found". Why this delay in connecting to Novell Netware through Cisco Switch. The same delay is not happening while we are connecting to 3Com Switch. We need you help and guidance to sort out this problem. Ismail Al-shelh [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37399&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cat 2950-24 [7:37374]
You don't disable STP on the port to the PC because STP is only run between Layer2 devices. I believe you are referring to PortFast. Elmer - Original Message - From: "Brian" To: Sent: Wednesday, March 06, 2002 2:34 AM Subject: Re: Cat 2950-24 [7:37374] > If you connect a computer to a switch port, it takes spanning tree a bit to > allow traffic to pass. If this is an individual host being connected, you > could try disabling spanning tree on the port.. > > Bri > > - Original Message - > From: "Ismail Al-Shelh" > To: > Sent: Tuesday, March 05, 2002 10:44 PM > Subject: Cat 2950-24 [7:37374] > > > > Dear all > > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed > > with Dos 6.22 Operating System. We used to connect this to our 3com > > Switch1100 with the dos driver provided by 3Com. The sequence of loading > > the 3com driver to connect to 3com Switch1100 is as follows: > > LSL.COM > > 3C90X.EXE > > IPXODI.COM > > NETX.EXE > > F: > > LOGIN > > This is in a batch file and when we run the batch file it will connect > > immediately. > > The problem I am facing while connect to CISCO CATALYST 2950-24 port is > that > > If I am > > running the same batch file it will not connect. > > I have to load the LSL.COM first and port on switch to which this computer > > is connected will be in Green color. But When > > I will load 3c90x.exe immediately the port on the switch color becomes > > amber. > > I have to wait for 1 to 1.5 minutes for the port color to become green > > and after that if load IPXODI.COM and NETX.EXE then it will connect. > > I can see this because I am sitting in front of the Cisco Switch. In > actual > > the end user will run the batch file sitting somewhere in his room and he > > will get a message "Novell Netware Server not > > Found". > > Why this delay in connecting to Novell Netware through Cisco Switch. The > > same > > delay is not happening while we are connecting to 3Com Switch. > > We need you help and guidance to sort out this problem. > > Ismail Al-shelh > > > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37388&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cat 2950-24 [7:37374]
you have a delay of 50 seconds or so because cisco uses the spanning tree protocol on most switches. This causes the port to not activate your pc for that amount of time. To resolve this, enable the port fast function on the port you have the pc connected to. I am sure someone here will explain it better than this, but this the issue in a nutshell. Larry Letterman Cisco Systems [EMAIL PROTECTED] -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]] Sent: Tuesday, March 05, 2002 10:45 PM To: [EMAIL PROTECTED] Subject: Cat 2950-24 [7:37374] Dear all We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed with Dos 6.22 Operating System. We used to connect this to our 3com Switch1100 with the dos driver provided by 3Com. The sequence of loading the 3com driver to connect to 3com Switch1100 is as follows: LSL.COM 3C90X.EXE IPXODI.COM NETX.EXE F: LOGIN This is in a batch file and when we run the batch file it will connect immediately. The problem I am facing while connect to CISCO CATALYST 2950-24 port is that If I am running the same batch file it will not connect. I have to load the LSL.COM first and port on switch to which this computer is connected will be in Green color. But When I will load 3c90x.exe immediately the port on the switch color becomes amber. I have to wait for 1 to 1.5 minutes for the port color to become green and after that if load IPXODI.COM and NETX.EXE then it will connect. I can see this because I am sitting in front of the Cisco Switch. In actual the end user will run the batch file sitting somewhere in his room and he will get a message "Novell Netware Server not Found". Why this delay in connecting to Novell Netware through Cisco Switch. The same delay is not happening while we are connecting to 3Com Switch. We need you help and guidance to sort out this problem. Ismail Al-shelh [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37379&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cat 2950-24 [7:37374]
If you connect a computer to a switch port, it takes spanning tree a bit to allow traffic to pass. If this is an individual host being connected, you could try disabling spanning tree on the port.. Bri - Original Message - From: "Ismail Al-Shelh" To: Sent: Tuesday, March 05, 2002 10:44 PM Subject: Cat 2950-24 [7:37374] > Dear all > We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed > with Dos 6.22 Operating System. We used to connect this to our 3com > Switch1100 with the dos driver provided by 3Com. The sequence of loading > the 3com driver to connect to 3com Switch1100 is as follows: > LSL.COM > 3C90X.EXE > IPXODI.COM > NETX.EXE > F: > LOGIN > This is in a batch file and when we run the batch file it will connect > immediately. > The problem I am facing while connect to CISCO CATALYST 2950-24 port is that > If I am > running the same batch file it will not connect. > I have to load the LSL.COM first and port on switch to which this computer > is connected will be in Green color. But When > I will load 3c90x.exe immediately the port on the switch color becomes > amber. > I have to wait for 1 to 1.5 minutes for the port color to become green > and after that if load IPXODI.COM and NETX.EXE then it will connect. > I can see this because I am sitting in front of the Cisco Switch. In actual > the end user will run the batch file sitting somewhere in his room and he > will get a message "Novell Netware Server not > Found". > Why this delay in connecting to Novell Netware through Cisco Switch. The > same > delay is not happening while we are connecting to 3Com Switch. > We need you help and guidance to sort out this problem. > Ismail Al-shelh > > [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37375&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cat 2950-24 [7:37374]
Dear all We have Pc with 3Com 3c90x-Tx 10/100 Network Card. This PC is installed with Dos 6.22 Operating System. We used to connect this to our 3com Switch1100 with the dos driver provided by 3Com. The sequence of loading the 3com driver to connect to 3com Switch1100 is as follows: LSL.COM 3C90X.EXE IPXODI.COM NETX.EXE F: LOGIN This is in a batch file and when we run the batch file it will connect immediately. The problem I am facing while connect to CISCO CATALYST 2950-24 port is that If I am running the same batch file it will not connect. I have to load the LSL.COM first and port on switch to which this computer is connected will be in Green color. But When I will load 3c90x.exe immediately the port on the switch color becomes amber. I have to wait for 1 to 1.5 minutes for the port color to become green and after that if load IPXODI.COM and NETX.EXE then it will connect. I can see this because I am sitting in front of the Cisco Switch. In actual the end user will run the batch file sitting somewhere in his room and he will get a message "Novell Netware Server not Found". Why this delay in connecting to Novell Netware through Cisco Switch. The same delay is not happening while we are connecting to 3Com Switch. We need you help and guidance to sort out this problem. Ismail Al-shelh [GroupStudy.com removed an attachment of type application/ms-tnef] Message Posted at: http://www.groupstudy.com/form/read.php?f=7&i=37374&t=37374 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
