IPX Problem [7:42735]
I have a network where corporate is connected to 3 branch offices through Point to Point. The branch office are also connected together in a full mesh frame-relay toplogy as a backup. The corporate office is also connected to few other small branches in a hub and spoke frame-relay topology. I was running IPX RIP by default between those networks and response time between IPX hosts and servers was not really bad. I decided to make some more changes to decrease the latency by configuring IPX eigrp between WAN Links only and left RIP on LAN interfaces. Instead of decreasing the latency it increased it by 4 times. Before EIGRP I copied a file and it took about 20 seconds. Now it's taking almost 4 minutes. I am curious where I went wrong. All I did to enable IPX Router eigrp 2 advertised all my WAN networks. network network and so on. I then removed those WAN networks from RIP routing by IPX router rip no network no network and so on. Note: I am also running EIGRP 1 for IP network. I don't think that it will conflict since both have under different Autonomous systems. Any suggestions folks. Regards, Ab Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=42735t=42735 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX Problem [7:42735]
did anything else change? I ask because on the surface, everything is fine. IPX EIGRP should have no effect on your throughput. I ran an eight site dual homed IPX network for several years, with no WAN issues other than the usual telco related problems. I've done numerous labs. the so called AS numbers in EIGRP are not relevant. IPX and IP are different router processes, and there is no conflict there. are you seeing all routes in all router's tables? got a loop in there somewhere? accidentally shut down some interfaces? got a telco problem that occurred coincidentally? checked your interface counters, your process counters? done some debugs while doing the file transfers? HTH Ali, Abbas wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... I have a network where corporate is connected to 3 branch offices through Point to Point. The branch office are also connected together in a full mesh frame-relay toplogy as a backup. The corporate office is also connected to few other small branches in a hub and spoke frame-relay topology. I was running IPX RIP by default between those networks and response time between IPX hosts and servers was not really bad. I decided to make some more changes to decrease the latency by configuring IPX eigrp between WAN Links only and left RIP on LAN interfaces. Instead of decreasing the latency it increased it by 4 times. Before EIGRP I copied a file and it took about 20 seconds. Now it's taking almost 4 minutes. I am curious where I went wrong. All I did to enable IPX Router eigrp 2 advertised all my WAN networks. network network and so on. I then removed those WAN networks from RIP routing by IPX router rip no network no network and so on. Note: I am also running EIGRP 1 for IP network. I don't think that it will conflict since both have under different Autonomous systems. Any suggestions folks. Regards, Ab Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=42748t=42735 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX Problem [7:42735]
Did you know you can do trace route with IPX on Cisco routers? It's not just an IP thing. I suggest you try this. Maybe you caused some weird routing somehow. Your network sounds sort of complicated and non-hierarchical. Maybe the branch offices used to communicate directly and how they go through the core and out into the outer reaches and back again. Trace route would let you determine if this is happening. Good luck. Let us know what you discover. This is an interesting problem. Priscilla At 03:52 AM 4/27/02, Ali, Abbas wrote: I have a network where corporate is connected to 3 branch offices through Point to Point. The branch office are also connected together in a full mesh frame-relay toplogy as a backup. The corporate office is also connected to few other small branches in a hub and spoke frame-relay topology. I was running IPX RIP by default between those networks and response time between IPX hosts and servers was not really bad. I decided to make some more changes to decrease the latency by configuring IPX eigrp between WAN Links only and left RIP on LAN interfaces. Instead of decreasing the latency it increased it by 4 times. Before EIGRP I copied a file and it took about 20 seconds. Now it's taking almost 4 minutes. I am curious where I went wrong. All I did to enable IPX Router eigrp 2 advertised all my WAN networks. network network and so on. I then removed those WAN networks from RIP routing by IPX router rip no network no network and so on. Note: I am also running EIGRP 1 for IP network. I don't think that it will conflict since both have under different Autonomous systems. Any suggestions folks. Regards, Ab Priscilla Oppenheimer http://www.priscilla.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=42752t=42735 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: NDS- IPX problem [7:12020]
Are you using all cisco equipment or are you mixing cisco with other vendors? If you are using multiple vendors, make sure the sap and rip updates are happening at the same time. (either when changes are made, or every so many seconds) a lot of vendors' default configs are to allow updates when changes are made, where cisco is every so many seconds. Either will work, but both have to be configured the same. If they aren't you'll have sporadic problems and neither equipment will hold sap and rip updates properly. -Patrick Keith Townsend 07/11/01 05:59PM Where are you seeing the two different trees. Are you seeing them from Display Servers or from the SAP list on the router or from a Netware Client. If you are seeing this from a Router or Server this is pretty normal. But if you are seeing this from the client then this points to a communications problem between the Servers or a NDS corruption. Try doing a Reset Router on all the NetWare boxes within 15 seconds of each other. Then try running DSRepairs on each individual box that has a copy of the DS. Start with the Master. I hope this helps. Keith Townsend MCSE, CNE, CCNA AISA Technologies 312-629-1100 www.aisatech.com nusrat khwaja wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... 1. One of my Netware5 server is showing two NDS trees instead of our single tree. The only difference is that the name of the real one is : a-b and the other one shown is a|b. a|b can not be opened but a-b is working. 2. At the same time, SHO IPX server on a Netware5 server shows only a few IPX servers but if I RESET ROUTER it shows all my IPX servers but only for about 15 minutes and then all except a few ipx servers disappear from sho ipx server. What could be wrong ?? _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=12130t=12020 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
NDS- IPX problem [7:12020]
1. One of my Netware5 server is showing two NDS trees instead of our single tree. The only difference is that the name of the real one is : a-b and the other one shown is a|b. a|b can not be opened but a-b is working. 2. At the same time, SHO IPX server on a Netware5 server shows only a few IPX servers but if I RESET ROUTER it shows all my IPX servers but only for about 15 minutes and then all except a few ipx servers disappear from sho ipx server. What could be wrong ?? _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=12020t=12020 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: NDS- IPX problem [7:12020]
Where are you seeing the two different trees. Are you seeing them from Display Servers or from the SAP list on the router or from a Netware Client. If you are seeing this from a Router or Server this is pretty normal. But if you are seeing this from the client then this points to a communications problem between the Servers or a NDS corruption. Try doing a Reset Router on all the NetWare boxes within 15 seconds of each other. Then try running DSRepairs on each individual box that has a copy of the DS. Start with the Master. I hope this helps. Keith Townsend MCSE, CNE, CCNA AISA Technologies 312-629-1100 www.aisatech.com nusrat khwaja wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... 1. One of my Netware5 server is showing two NDS trees instead of our single tree. The only difference is that the name of the real one is : a-b and the other one shown is a|b. a|b can not be opened but a-b is working. 2. At the same time, SHO IPX server on a Netware5 server shows only a few IPX servers but if I RESET ROUTER it shows all my IPX servers but only for about 15 minutes and then all except a few ipx servers disappear from sho ipx server. What could be wrong ?? _ Do You Yahoo!? Get your free @yahoo.com address at http://mail.yahoo.com Message Posted at: http://www.groupstudy.com/form/read.php?f=7i=12034t=12020 -- FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco1601R and IPX problem
Yes I have but then it doesn't work .
I've logged a call with TAC now so lets see what they can come up with .
Ive done copy pastes all the way to ensure no mistakes .
I'll keep you up so speed .
Cheers
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email: [EMAIL PROTECTED] mailto:[EMAIL PROTECTED]
Web:http://www.westcon.co.za http://www.westcon.co.za
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola, Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached thereto ("the
message") may contain confidential information, and is intended for a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit, review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all copies thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form whatsoever, without
the sender's expressed written consent, is prohibited. No opinion expressed
or implied by the sender necessarily constitutes the opinion of WESTCON.
This message does not constitute a guarantee or proof of the facts mentioned
therein. WESTCON accepts no responsibility or liability in respect of:-
* any opinion or guarantee of fact, whether expressed or implied; or
any action or failure to act as a result of any information contained in
this message, unless such information or opinion has been confirmed in
writing by an authorised WESTCON director.
-Original Message-
From: [EMAIL PROTECTED] [SMTP:[EMAIL PROTECTED]]
Sent: Saturday, December 16, 2000 10:34 AM
To: Olden Pieterse
Subject:Re: Cisco1601R and IPX problem
That's very strange. Are you sure that image in the flash
is named exactly as 'system boot' command specifies ? Have
you tried to remove 'system boot' command to see will it
boot from flash ?
Sasa
Olden Pieterse wrote:
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-RBOOT-R), Version 12.0(3)T, RELEASE
SOFTWARE
(fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 22-Feb-99 23:05 by ccai
Image text-base: 0x04020060, data-base: 0x02005000
Here is the show ver of the failed session
ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Router uptime is 0 minutes
System restarted by power-on
System image file is "bootflash:"
cisco 1601 (68360) processor (revision C) with 7680K/512K bytes of
memory.
Processor board ID 17549539, with hardware revision 0002
1 Ethernet/IEEE 802.3 interface(s)
Unrecognized interface found (0-1 = Motherboard interfaces 2 =
WIC)
Interface 1 unrecognized by boothelper
System/IO memory with parity disabled
8192K bytes of DRAM onboard
System running from ROM
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read/Write)
Configuration register is 0x2102
As you can see it tries to boot off bootflash .
The config states that it must boot off the flash as youwill see
below
-- show running-config --
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
boot system flash c1600-ny-mz.120-13.bin
!
ip subnet-zero
!
!
interface Ethernet0
ip address 192.168.10.194 255.255.255.0
no ip directed-broadcast
no ip route-cache
!
no ip http server
!
line con 0
transport input none
line vty 0 4
login
!
end
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Cisco1601R and IPX problem
Hi there gang
I've got a customer's 1601r and for the life of it it does not like to boot
the ios image from flash (c1600-ny-mz) coldly
If I make it boot from tftp then its fine (cold and warm boot )
If I cold boot it from flash it goes into boot mode i.e boot from the
bootstrap
If I warm boot (reload) it from flash it works fine .
If anyone has similar problems plse let me know and if so , what image is
the most suitable
Its got enough flash ram in it .
Thanks in advance
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email: [EMAIL PROTECTED] mailto:[EMAIL PROTECTED]
Web:http://www.westcon.co.za http://www.westcon.co.za
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola, Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached thereto ("the
message") may contain confidential information, and is intended for a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit, review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all copies thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form whatsoever, without
the sender's expressed written consent, is prohibited. No opinion expressed
or implied by the sender necessarily constitutes the opinion of WESTCON.
This message does not constitute a guarantee or proof of the facts mentioned
therein. WESTCON accepts no responsibility or liability in respect of:-
* any opinion or guarantee of fact, whether expressed or implied; or
any action or failure to act as a result of any information contained in
this message, unless such information or opinion has been confirmed in
writing by an authorised WESTCON director.
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: Cisco1601R and IPX problem
Olden Pieterse wrote: I've got a customer's 1601r and for the life of it it does not like to boot the ios image from flash (c1600-ny-mz) coldly Send us output from 'show version'. Saa _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco1601R and IPX problem
The register is 0x2102 if that's what ur looking for .
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email: [EMAIL PROTECTED] mailto:[EMAIL PROTECTED]
Web:http://www.westcon.co.za http://www.westcon.co.za
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola, Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached thereto ("the
message") may contain confidential information, and is intended for a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit, review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all copies thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form whatsoever, without
the sender's expressed written consent, is prohibited. No opinion expressed
or implied by the sender necessarily constitutes the opinion of WESTCON.
This message does not constitute a guarantee or proof of the facts mentioned
therein. WESTCON accepts no responsibility or liability in respect of:-
* any opinion or guarantee of fact, whether expressed or implied; or
any action or failure to act as a result of any information contained in
this message, unless such information or opinion has been confirmed in
writing by an authorised WESTCON director.
-Original Message-
From: [EMAIL PROTECTED] [SMTP:[EMAIL PROTECTED]]
Sent: Tuesday, December 12, 2000 4:34 PM
To: Olden Pieterse
Cc: [EMAIL PROTECTED]
Subject:Re: Cisco1601R and IPX problem
Olden Pieterse wrote:
I've got a customer's 1601r and for the life of it it does not
like to boot
the ios image from flash (c1600-ny-mz) coldly
Send us output from 'show version'.
Sasa
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco1601R and IPX problem
Cisco Internetwork Operating System Software
IOS (tm) 1600 Software (C1600-RBOOT-R), Version 12.0(3)T, RELEASE SOFTWARE
(fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Mon 22-Feb-99 23:05 by ccai
Image text-base: 0x04020060, data-base: 0x02005000
Here is the show ver of the failed session
ROM: System Bootstrap, Version 12.0(3)T, RELEASE SOFTWARE (fc1)
Router uptime is 0 minutes
System restarted by power-on
System image file is "bootflash:"
cisco 1601 (68360) processor (revision C) with 7680K/512K bytes of memory.
Processor board ID 17549539, with hardware revision 0002
1 Ethernet/IEEE 802.3 interface(s)
Unrecognized interface found (0-1 = Motherboard interfaces 2 = WIC)
Interface 1 unrecognized by boothelper
System/IO memory with parity disabled
8192K bytes of DRAM onboard
System running from ROM
8K bytes of non-volatile configuration memory.
4096K bytes of processor board PCMCIA flash (Read/Write)
Configuration register is 0x2102
As you can see it tries to boot off bootflash .
The config states that it must boot off the flash as youwill see below
-- show running-config --
Building configuration...
Current configuration:
!
version 12.0
no service pad
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname Router
!
boot system flash c1600-ny-mz.120-13.bin
!
ip subnet-zero
!
!
interface Ethernet0
ip address 192.168.10.194 255.255.255.0
no ip directed-broadcast
no ip route-cache
!
no ip http server
!
line con 0
transport input none
line vty 0 4
login
!
end
Thanks a stack !
Cheers
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email: [EMAIL PROTECTED] mailto:[EMAIL PROTECTED]
Web:http://www.westcon.co.za http://www.westcon.co.za
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola, Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached thereto ("the
message") may contain confidential information, and is intended for a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit, review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all copies thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form whatsoever, without
the sender's expressed written consent, is prohibited. No opinion expressed
or implied by the sender necessarily constitutes the opinion of WESTCON.
This message does not constitute a guarantee or proof of the facts mentioned
therein. WESTCON accepts no responsibility or liability in respect of:-
* any opinion or guarantee of fact, whether expressed or implied; or
any action or failure to act as a result of any information contained in
this message, unless such information or opinion has been confirmed in
writing by an authorised WESTCON director.
-Original Message-
From: [EMAIL PROTECTED] [SMTP:[EMAIL PROTECTED]]
Sent: Tuesday, December 12, 2000 4:34 PM
To: Olden Pieterse
Cc: [EMAIL PROTECTED]
Subject: Re: Cisco1601R and IPX problem
Olden Pieterse wrote:
I've got a customer's 1601r and for the life of it it does not
like to boot
the ios image from flash (c1600-ny-mz) coldly
Send us output from 'show version'.
Sasa
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: Cisco1601R and IPX problem
Hello Olden,
Just a few ideas that came to mind:
Did you check a configuration register value in "show ver" ? Is it 0x2102 or
something else ?
Do you have any "boot system flash XXX" config command in case when boot
from flash fails ?
Do you see any messages on the console when flash boot fails ?
WBR,
Alexander Krastelev
Systems Engineer
Uniplace AG
Förrlibuckstrasse 178
8005 Zürich
Tel. +41 1 276 19 25
Fax. +41 1 276 19 20
www.uniplace.com
-Original Message-
From: Olden Pieterse [mailto:[EMAIL PROTECTED]]
Sent: Tuesday, December 12, 2000 2:19 PM
Cc: [EMAIL PROTECTED]
Subject: Cisco1601R and IPX problem
Importance: High
Hi there gang
I've got a customer's 1601r and for the life of it it does
not like to boot
the ios image from flash (c1600-ny-mz) coldly
If I make it boot from tftp then its fine (cold and warm boot )
If I cold boot it from flash it goes into boot mode i.e boot from the
bootstrap
If I warm boot (reload) it from flash it works fine .
If anyone has similar problems plse let me know and if so ,
what image is
the most suitable
Its got enough flash ram in it .
Thanks in advance
Olden Pieterse
Pre-Sales Consultant
Westcon
Tel: +27 21 415 7211
Fax: +27 21 419 7537
Mobile: +27 82 564 0709
Email:[EMAIL PROTECTED] mailto:[EMAIL PROTECTED]
Web: http://www.westcon.co.za http://www.westcon.co.za
Remember, our product range includes:
3Com, Addtron, APC, IMC, Cisco, Extreme, Lucent, Motorola,
Nortel-Networks
and Ramp.
E-mail Disclaimer:
Any email message from a WESTCON employee, and all attached
thereto ("the
message") may contain confidential information, and is intended for a
specific addressee and purpose. If you are not the addressee
* you may not use, disclose, copy, distribute, retransmit, review,
disseminate or take any action based on the contents thereof;
* kindly inform the sender immediately and destroy all
copies thereof.
Any copying, publication, dissemination, retransmission or
disclosure of this message, or part thereof, in any form
whatsoever, without
the sender's expressed written consent, is prohibited. No
opinion expressed
or implied by the sender necessarily constitutes the opinion
of WESTCON.
This message does not constitute a guarantee or proof of the
facts mentioned
therein. WESTCON accepts no responsibility or liability in
respect of:-
* any opinion or guarantee of fact, whether expressed or
implied; or
any action or failure to act as a result of any information
contained in
this message, unless such information or opinion has been confirmed in
writing by an authorised WESTCON director.
_
FAQ, list archives, and subscription info:
http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
_
FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html
Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX Problem
Shane, It seems you have an IP only image. You may have been confused by the L in the image, but as far as I know when the L appears in that position it just indicates a relocatable image, not IPX. Appletalk isn't anywhere in there. Cheers, Gareth ""Shane Stockman"" [EMAIL PROTECTED] wrote in message [EMAIL PROTECTED]">news:[EMAIL PROTECTED]... This might seem silly but I am trying to enable ipx routing on my router and it just keeps telling unrecog command , even though I am in global config mode.When I do a ipx ? , i get unrecog command in global config mode.Same with apple IOS (tm) 1600 Software (C1600-Y-L), Version 12.0(3), RELEASE SOFTWARE (fc1) Thanks _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. Share information about yourself, create your own public profile at http://profiles.msn.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
IPX Problem
This might seem silly but I am trying to enable ipx routing on my router and it just keeps telling unrecog command , even though I am in global config mode.When I do a ipx ? , i get unrecog command in global config mode.Same with apple IOS (tm) 1600 Software (C1600-Y-L), Version 12.0(3), RELEASE SOFTWARE (fc1) Thanks _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. Share information about yourself, create your own public profile at http://profiles.msn.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: IPX Problem
You need a desktop or enterprise image. It seems you only have an IP IOS image. -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]On Behalf Of Shane Stockman Sent: Friday, November 03, 2000 11:38 AM To: [EMAIL PROTECTED] Subject: IPX Problem This might seem silly but I am trying to enable ipx routing on my router and it just keeps telling unrecog command , even though I am in global config mode.When I do a ipx ? , i get unrecog command in global config mode.Same with apple IOS (tm) 1600 Software (C1600-Y-L), Version 12.0(3), RELEASE SOFTWARE (fc1) Thanks _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. Share information about yourself, create your own public profile at http://profiles.msn.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX Problem
The IOS may not support IPX. Go to the CCO site and research it, but more than likely that is the problem. Raul -Original Message- From: Shane Stockman [EMAIL PROTECTED] To: [EMAIL PROTECTED] [EMAIL PROTECTED] Date: Friday, November 03, 2000 3:06 PM Subject: IPX Problem This might seem silly but I am trying to enable ipx routing on my router and it just keeps telling unrecog command , even though I am in global config mode.When I do a ipx ? , i get unrecog command in global config mode.Same with apple IOS (tm) 1600 Software (C1600-Y-L), Version 12.0(3), RELEASE SOFTWARE (fc1) Thanks _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. Share information about yourself, create your own public profile at http://profiles.msn.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: IPX Problem
It sounds like your running an IOS that doesn't have IPX includedtry upgrading your IOS Thanks, Chris Boyd Network Support CCNA Alex Lee, Inc. 120 4th Street SW Hickory, NC 28601 (828) 323-4103 http://www.alexlee.com - Original Message - From: "Shane Stockman" [EMAIL PROTECTED] To: [EMAIL PROTECTED] Sent: Friday, November 03, 2000 2:38 PM Subject: IPX Problem This might seem silly but I am trying to enable ipx routing on my router and it just keeps telling unrecog command , even though I am in global config mode.When I do a ipx ? , i get unrecog command in global config mode.Same with apple IOS (tm) 1600 Software (C1600-Y-L), Version 12.0(3), RELEASE SOFTWARE (fc1) Thanks _ Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. Share information about yourself, create your own public profile at http://profiles.msn.com. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
