Re: BRI Problem
This is a bit of a shot in the dark - I use a different switch type and no SPIDs so things may show up differently. I notice that you have three activated CCBs, but only one active call. If I make a call in my setup, I only expect to see one activated CCB per active call. However there is a bug that affects primary rate services (don't know if it also affects BRI) where sometimes the CCBs are not released after a call. This means you can't use that channel until the interface is reset and the CCBs cleared. This is probably not what is causing your problem, but if you want to rule it out, shut/no shut the BRI interface and check that there are no activated CCBs and no active calls. Then try again. JMcL -- Forwarded by Jenny Mcleod/NSO/CSDA on 08/02/2001 08:46 am --- John Neiberger <[EMAIL PROTECTED]>@groupstudy.com on 08/02/2001 04:14:42 am Please respond to John Neiberger <[EMAIL PROTECTED]> Sent by: [EMAIL PROTECTED] To: [EMAIL PROTECTED] cc: [EMAIL PROTECTED] Subject: Re: BRI Problem I've read that for certain switch types, for both channels to work you need to add the LDN for each B channel to your spid statements. That might be worth checking into a little further. John > > I have 2 Cisco routers connected by 1 ISDN link between the two. Router A is > setup to receive calls and Router B is setup to place the calls. What is > happening is Router B makes the call but only 1 B channel is coming up. Both > B channels on router B are good and I get the following > > Layer 1 Status: > ACTIVE > Layer 2 Status: > TEI = 69, State = MULTIPLE_FRAME_ESTABLISHED > TEI = 70, State = MULTIPLE_FRAME_ESTABLISHED > Layer 3 Status: > 1 Active Layer 3 Call(s) > Activated dsl 0 CCBs = 3 > CCB:callid=0, sapi=0, ces=1, B-chan=0 > CCB:callid=E1B6, sapi=0, ces=1, B-chan=1 > CCB:callid=E4C6, sapi=0, ces=2, B-chan=0 > > I have set the dialer load threshold to 1 on Router B and it is using PPP > Multilink > > I have two dialer map statements on router B that calls the SPIDS on Router > A. > > When I do a Show dialer I get the following > > BRI0 - dialer type = ISDN > > Dial String Successes FailuresLast called Last status > 9825 7 128930:00:29 successful > 98254445 3 129000:00:05 failed > 0 incoming call(s) have been screened. > BRI0: B-Channel 1 > Idle timer (2147483 secs), Fast idle timer (30 secs) > Wait for carrier (30 secs), Re-enable (15 secs) > Time until disconnect 2147482 secs > Current call connected 3:17:59 > Connected to 9825444(FIRE) > BRI0: B-Channel 2 > Idle timer (2147483 secs), Fast idle timer (30 secs) > Wait for carrier (30 secs), Re-enable (15 secs) > > Router B constantly dials. Anybody have any Ideas? > Spids on Router A are ok > > Thanks > > _ > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Find the best deals on the web at AltaVista Shopping! http://www.shopping.altavista.com _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: BRI Problem
Hi, You need to have the dialer-load and/or ppp multi set on both routers. You debug seems to indicate the ISDN service is fine. Oh make sure your dialer-load thresholds work for for both directions. Teunis Hobart, Tasmania Australia On Wednesday, February 07, 2001 at 09:14:42 AM, John Neiberger wrote: > I've read that for certain switch types, for both channels to work you need to add >the LDN for each B channel to your spid statements. That might be worth checking >into a little further. > > John > > > > > I have 2 Cisco routers connected by 1 ISDN link between the two. Router A is > > setup to receive calls and Router B is setup to place the calls. What is > > happening is Router B makes the call but only 1 B channel is coming up. Both > > B channels on router B are good and I get the following > > > > Layer 1 Status: > > ACTIVE > > Layer 2 Status: > > TEI = 69, State = MULTIPLE_FRAME_ESTABLISHED > > TEI = 70, State = MULTIPLE_FRAME_ESTABLISHED > > Layer 3 Status: > > 1 Active Layer 3 Call(s) > > Activated dsl 0 CCBs = 3 > > CCB:callid=0, sapi=0, ces=1, B-chan=0 > > CCB:callid=E1B6, sapi=0, ces=1, B-chan=1 > > CCB:callid=E4C6, sapi=0, ces=2, B-chan=0 > > > > I have set the dialer load threshold to 1 on Router B and it is using PPP > > Multilink > > > > I have two dialer map statements on router B that calls the SPIDS on Router > > A. > > > > When I do a Show dialer I get the following > > > > BRI0 - dialer type = ISDN > > > > Dial String Successes FailuresLast called Last status > > 9825 7 128930:00:29 successful > > 98254445 3 129000:00:05 failed > > 0 incoming call(s) have been screened. > > BRI0: B-Channel 1 > > Idle timer (2147483 secs), Fast idle timer (30 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > Time until disconnect 2147482 secs > > Current call connected 3:17:59 > > Connected to 9825444(FIRE) > > BRI0: B-Channel 2 > > Idle timer (2147483 secs), Fast idle timer (30 secs) > > Wait for carrier (30 secs), Re-enable (15 secs) > > > > Router B constantly dials. Anybody have any Ideas? > > Spids on Router A are ok > > > > Thanks > > > > _ > > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. > > > > _ > > FAQ, list archives, and subscription info: >http://www.groupstudy.com/list/cisco.html > > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > > Find the best deals on the web at AltaVista Shopping! > http://www.shopping.altavista.com > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] > > -- www.tasmail.com _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
Re: BRI Problem
I've read that for certain switch types, for both channels to work you need to add the LDN for each B channel to your spid statements. That might be worth checking into a little further. John > > I have 2 Cisco routers connected by 1 ISDN link between the two. Router A is > setup to receive calls and Router B is setup to place the calls. What is > happening is Router B makes the call but only 1 B channel is coming up. Both > B channels on router B are good and I get the following > > Layer 1 Status: > ACTIVE > Layer 2 Status: > TEI = 69, State = MULTIPLE_FRAME_ESTABLISHED > TEI = 70, State = MULTIPLE_FRAME_ESTABLISHED > Layer 3 Status: > 1 Active Layer 3 Call(s) > Activated dsl 0 CCBs = 3 > CCB:callid=0, sapi=0, ces=1, B-chan=0 > CCB:callid=E1B6, sapi=0, ces=1, B-chan=1 > CCB:callid=E4C6, sapi=0, ces=2, B-chan=0 > > I have set the dialer load threshold to 1 on Router B and it is using PPP > Multilink > > I have two dialer map statements on router B that calls the SPIDS on Router > A. > > When I do a Show dialer I get the following > > BRI0 - dialer type = ISDN > > Dial String Successes FailuresLast called Last status > 9825 7 128930:00:29 successful > 98254445 3 129000:00:05 failed > 0 incoming call(s) have been screened. > BRI0: B-Channel 1 > Idle timer (2147483 secs), Fast idle timer (30 secs) > Wait for carrier (30 secs), Re-enable (15 secs) > Time until disconnect 2147482 secs > Current call connected 3:17:59 > Connected to 9825444(FIRE) > BRI0: B-Channel 2 > Idle timer (2147483 secs), Fast idle timer (30 secs) > Wait for carrier (30 secs), Re-enable (15 secs) > > Router B constantly dials. Anybody have any Ideas? > Spids on Router A are ok > > Thanks > > _ > Get Your Private, Free E-mail from MSN Hotmail at http://www.hotmail.com. > > _ > FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html > Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] Find the best deals on the web at AltaVista Shopping! http://www.shopping.altavista.com _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]