Re[2]: gsr12012 show command..
> The following is from a GSR 12012, running 12.0(10)S1 > router#sho int ser 1/0 > router#sho controllers serial 1/0 there also: r1#sh gsr Slot 0 type = Route Processor state = IOS Running PRIMARY Slot 1 type = 1 port ATM Over SONET OC12c/STM-4c state = Line Card Enabled Slot 2 type = 4 port ATM Over SONET OC-3c/STM-1 state = Line Card Enabled [...] LC-Slot1#show ver Cisco Internetwork Operating System Software IOS (tm) GS Software (GLC1-LC-M), Version 12.0(15)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) TAC Support: http://www.cisco.com/cgi-bin/ibld/view.pl?i=support Copyright (c) 1986-2001 by cisco Systems, Inc. Compiled Fri 26-Jan-01 18:42 by pwade Image text-base: 0x40010950, data-base: 0x4048 ROM: System Bootstrap, Version 12.0(2609:183828) [bdelaney-blizzard.commit 104], DEVELOPMENT SOFTWARE ROM: GS Software (GLC1-LC-M), Version 12.0(15)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1) LC-Slot1 uptime is 17 hours, 37 minutes System restarted at 16:14:09 MET Tue Jan 30 2001 Running default software cisco OC12-ATM (R5000) processor (revision 0x02) with 262144K bytes of memory. R5000 CPU at 200Mhz, Implementation 35, Rev 2.1 Last reset from mbus reset Configuration register is 0x0 LC-Slot1#sh contr TX SAR (Patch 3.2.2) is Operational; RX SAR (Patch 3.2.2) is Operational; Interface Configuration Mode: STM-4 Active Maker Channels: total # 5 VCID VPI ChID Type OutputInfoInPkts InOAMs MacString 1 0 2D08 UBR0C019120 152740 2D08200003000800 00 2 0 2D28 UBR0C019140 00 2D28200003000800 00 3 0 2D48 UBR0C0191604020 2D48200003000800 00 4 0 2E88 UBR0C019180 3314750 2E88200003000800 00 5 0 2EA8 UBR0C0191A0 1522480 2EA8200003000800 00 SAR Counters: tx_paks459851 tx_abort_paks 0 tx_idle_cells 2584471704 rx_paks499189 rx_drop_paks 0 rx_discard_cells10 Host Counters: rx_crc_err_paks 0 rx_giant_paks 0 rx_abort_paks0 rx_crc10_cells 0 rx_tmout_paks0 rx_unknown_paks0 rx_out_buf_paks 0 rx_unknown_vc_paks 0 rx_len_err_paks 0 rx_len_crc32_err_paks 0 LC-Slot1#sh contr ? atmShow ATM controllers events LC event counters fiaFabric Interface ASIC info frfab From Fab (TX) io IO information l3 L3 information ratelimit Rate limit information rewrites L2 rewrite table tofab To Fab (RX) | Output modifiers -- Regards, Adam Obszyñski ATM Inc. +48-22-5156418 _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
RE: gsr12012 show command..
Wow, you sound desperate! I hope this tells you something mate. The following is from a GSR 12012, running 12.0(10)S1 ___ router#sho int ser 1/0 Serial1/0 is up, line protocol is up Hardware is Packet over DS3 Description: Internet address is x.x.x.x /30 MTU 4470 bytes, BW 44210 Kbit, DLY 200 usec, rely 255/255, load 1/255 Encapsulation HDLC, crc 16, loopback not set Keepalive set (10 sec) Last input 00:00:07, output 00:00:02, output hang never Last clearing of "show interface" counters never Queueing strategy: fifo Output queue 0/40, 0 drops; input queue 0/75, 0 drops 5 minute input rate 6000 bits/sec, 20 packets/sec 5 minute output rate 6000 bits/sec, 12 packets/sec 43343044 packets input, 417655339 bytes, 0 no buffer Received 0 broadcasts, 267 runts, 0 giants, 0 throttles 0 parity 777 input errors, 57 CRC, 242 frame, 0 overrun, 0 ignored, 211 abort 42328073 packets output, 594197015 bytes, 0 underruns 0 output errors, 0 applique, 0 interface resets 0 output buffer failures, 0 output buffers swapped out 1 carrier transitions router#sho controllers serial 1/0 Interface Serial1/0 (DS3 port 0) hwidb = 0x61614360 ssb = , ds = x Line state is up rxLOS inactive, rxLOF inactive, rxAIS inactive txAIS inactive, rxRAI inactive, txRAI inactive Current configurable parameter settings: Loopback is none, Framing is c-bit Clock source is line, Cable length is 50 DSU mode is cisco, DSU bandwidth limit is 44210 Payload scrambling is disabled, CRC is 16 Bert pattern is disabled, Bert interval is 0 Transmitter delay is 0, Encapsulation is HDLC Idle character is flags, Invert data is disabled Remote fullrate has no request outstanding Remote accept is enabled, MTU is 4470 MIB information: Data in current interval (517 seconds elapsed): 0 Line Code Violations, 0 P-bit Coding Violations 0 C-bit Coding Violations 0 P-bit Err Secs, 0 P-bit Sev Err Secs 0 Sev Err Framing Secs, 0 Unavailable Secs 0 Line Errored Secs, 0 C-bit Errored Secs, 0 C-bit Sev Err Secs No alarms detected. -Original Message- From: ? To: cisco group study Sent: 1/30/2001 5:40 PM Subject: gsr12012 show command.. in the gsr12012, what show command will give us a information of specific line.. etc.. oc3 or oc12.. show line ? or show port ? or show interface ? plz, let me know about it... if possible, could you give me some dump of that show command? it's so urgent.. plz.. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED] _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]
gsr12012 show command..
in the gsr12012, what show command will give us a information of specific line.. etc.. oc3 or oc12.. show line ? or show port ? or show interface ? plz, let me know about it... if possible, could you give me some dump of that show command? it's so urgent.. plz.. _ FAQ, list archives, and subscription info: http://www.groupstudy.com/list/cisco.html Report misconduct and Nondisclosure violations to [EMAIL PROTECTED]