Re: [slim] Gross Failure - Barcode in display
DoomWolf;436331 Wrote: I'd recommend you contact Logitech support. Remember, this forum isn't an official support channel. There could be a more fundamental fault with your SB3. I followed your advice and after a number of conversations it was decided I had a hardware problem. I have been sent a new SB3 which I have now installed. May I publicly thanks the support team for their help, and the European Depot for their prompt delivery once the decision had been taken to give me new SB. Top marks for all. -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
Your original post shows you were using a very old version of 7.3.3 with old firmware. Bugs that could cause what you were seeing were fixed in the official 7.3.3 firmware, especially bugs related to Ogg Vorbis which you also mentioned. So you will probably be fine now. -- andyg andyg's Profile: http://forums.slimdevices.com/member.php?userid=3292 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
andyg;444896 Wrote: Your original post shows you were using a very old version of 7.3.3 with old firmware. Bugs that could cause what you were seeing were fixed in the official 7.3.3 firmware, especially bugs related to Ogg Vorbis which you also mentioned. So you will probably be fine now. The problems continued even with the latest 7.3.3 I have put the old SB3 to bed, but when I have time I might see if I can make it behave. Off topic A couple of days ago I received a Special Edition Beresford 7520 (Caiman) Very, very nice. See . . . No. I will start a new thread. -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
OK, if you still see it on the released 7.3.3, does it occur only when playing a specific file or radio stream? File a bug and attach the file or list the radio stream it occurs on. -- andyg andyg's Profile: http://forums.slimdevices.com/member.php?userid=3292 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
andyg;444904 Wrote: OK, if you still see it on the released 7.3.3, does it occur only when playing a specific file or radio stream? File a bug and attach the file or list the radio stream it occurs on. This was the subject of a few conversations with Dan Evans. See Gross failure of SB3 - barcode in display [Incident: 090629-003132] on your own database. Most of the time it was fine, but if I powered down (or if the supply failed) the factory test barcode would appear. With some persistence I would be able to force the SB3 to re-initialise, but to get it to talk to SC I would have to re-install 7.3.3 over the last installation - I never found another way to get going. Ben was not happy with that - I guess my prefs file might be quite messy now. In the end Dan said, probably a hardware fault - have a new one. I wasn't going to argue! -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
I'd recommend you contact Logitech support. Remember, this forum isn't an official support channel. There could be a more fundamental fault with your SB3. -- DoomWolf DoomWolf's Profile: http://forums.slimdevices.com/member.php?userid=8839 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
Repeat problem as reported at the top of this post. This time everything went silent. I unplugged the SB3 power supply and rebooted. The scrolling bar code appeared, but in the scroll the prompts for re-registering to the network appear. Once that was effected I was listening again. Any gurus with ideas? Perhaps one of the Logitech team could comment? -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
[slim] Gross Failure - Barcode in display
I leave my six month old SB3 on all the time, but this morning I had problems when turning on the power amp. The SB3 would not respond to commands from either the IR remote or the laptop on which Squeezecentre is hosted. I powered down the SB3 for a few seconds and re-started. I now see a slowly scrolling display of vertical and diagonal lines. The lines appear as blocks of varying density showing upper and lower squares in the display - I see 4,6 or 8 squares followed by a diagonal. Fiddling around I can get the SB3 to play radio for a few seconds, and it will attempt to re-register after a hard reset, but what is going on? Gross hardware failure? No. Not hardware failure. I have managed a hard reset (powerdown, powerup). Everything now seems to be working except alien BBC. Ideas please. -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
Try a Xilinx reset on the SB3? (from the wiki): 1. Disconnect the power 2. Press and hold 1 on the remote 3. Reconnect the power 4. Release the 1 button when you see Programming xilinx on the screen -- tcutting tcutting's Profile: http://forums.slimdevices.com/member.php?userid=17402 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
tcutting;433701 Wrote: Try a Xilinx reset on the SB3? Thanks. Tried that. Scrolling Barcode appeared again. Holding down Brightness button on remote pushed the SB3 into setup mode, but the barcode was scrolling as a puctuation to the nromal text prompts for setup. with very little running. Squeezecentre is very tardy in responding to any mouse clicks and the SB3 is unpredictable in its obedience to commands from the IR remote. I noticed my laptop was quite warm - 70% CPU usage at one pont On the other hand it is processing OGG internet radio and will downsample a hibit track from 2L with the CPU running at 24%. I haven't a clue? Should I re-install Squeezecentre? -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
A few hours later: Reinstalled Squeezecenter and that forced a firmware upgrade. All seems well. A corrupted Squeezecenter installation? But why? And what was the scrolling barcode about in the display. If one of the development team would offer a view I would be grateful. Squeezecentre now reports Version: 7.3.3 - 27044 @ Mon Jun 15 15:14:08 PDT 2009 so I am now using a slightly later 7.3.3 -- Labarum Brian Squeezebox 3 Classic and Virgin Cable Box Beresford DAC TC-7510 MK6/4 - Quad 405-2 refurbished by 405man Quart 980s Speakers Boom in kitchen. Labarum's Profile: http://forums.slimdevices.com/member.php?userid=19963 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
Re: [slim] Gross Failure - Barcode in display
Perhaps the SB3 firmware corrupted? Installing a newer release of Squeezecenter (finished 7.3.3 release, build 27044) then would have caused it to push out the latest firmware version 127 which would overwrite the previous corrupted one. -- DoomWolf DoomWolf's Profile: http://forums.slimdevices.com/member.php?userid=8839 View this thread: http://forums.slimdevices.com/showthread.php?t=64704 ___ discuss mailing list discuss@lists.slimdevices.com http://lists.slimdevices.com/mailman/listinfo/discuss
