Re: [Elecraft] KX3 digital
Don is spot on. I have filter macros built in DM780 to center my signal of choice and then narrow the filters SW needed. This greatly helps grabbing those weak signals of interest. 73 KD8NNU Don Sent from my HTC on the Now Network from Sprint! - Reply message - From: "Don Wilhelm" Date: Sat, Jan 12, 2013 1:25 am Subject: [Elecraft] KX3 digital To: It used to be that 5 watts on PSK31 was all that was needed, most all operators were using low power because it worked well. Most advice was to keep the power low - below 20 watts if I recall. As time went by, the power levels used on PSK31 have crept up and many operators are now using 100 watts or more. That kind of power in the narrow bandwidth of common PSK wattering holes will take over the AGC in the receiver because most are using bandwidths of 2.5 kHz or greater to see the full waterfall display. The AGC will respond to the strongest signal within the filter bandwidth and will make weaker stations more difficult to copy. Sometimes turning off the AGC will help, but concentrating on the station you wish to copy and narrowing the IF filter bandwidth will help even more. If you only want to work one station, there is no need to see the entire PSK31 band. Narrow the receiver filter and use the VFO to tune the desired station to the center of the IF passband. 73, Don W3FPR On 1/11/2013 6:13 PM, Ariel Jacala wrote: > 5 watts on PSK will work if you are in an empty section on the waterfall. In > a crowded situation with strong signals nearby, you will be stepped on and > obliterated by the strong signal. Certain DX stations are notorious for > overdriving the waterfall and wiping out other signals. You are better off > calling CQ in location away from nearby strong signals. At 5 watts your > printing on the waterfall can be faint depending on propagation. I did get > Hawaii once on PSK with my K2. My luck with PSK has always been better at > 25-30 watts. That is just the nature of this mode. At QRP power, CW is much > more efficient. Make sure you have enough drive to just trigger the ALC > circuit. You are also better off decoding the PSK signal with Fldigi or > DM780 - just a better PSK experience with the macros and all. > > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Elecraft Digest, Vol 104, Issue 47
you put enuf downward preassure on the screwdriver and it works everytime and get a good machined set of tools Holy Cow its not a big block v8 On 12/27/2012 6:00 PM, elecraft-requ...@mailman.qth.net wrote: Send Elecraft mailing list submissions to elecraft@mailman.qth.net To subscribe or unsubscribe via the World Wide Web, visit http://mailman.qth.net/mailman/listinfo/elecraft or, via email, send a message with subject or body 'help' to elecraft-requ...@mailman.qth.net You can reach the person managing the list at elecraft-ow...@mailman.qth.net When replying, please edit your Subject line so it is more specific than "Re: Contents of Elecraft digest..." Today's Topics: 1. KPA500 PWR Display (ac...@aol.com) 2. Re: Problem with a K3 screw - suggestions needed (Ian White GM3SEK) 3. test (ac...@aol.com) 4. Re: New Output Power Issue, and a new question (Richard Fjeld) 5. Re: KPA500 PWR Display (Jack Brindle) 6. Re: KPA500 PWR Display (ac...@aol.com) 7. Re: KPA500 PWR Display (Ken K3IU) 8. Fwd: KX3 Micro Manual Available in Apple App Store from Elecraft Digest, Vol 103, Issue 32 (Jeffrey Blumenfeld) 9. Re: Use of the subject line. (Jim Rhodes) 10. Re: KPA500 PWR Display (Jack Brindle) 11. Re: Problem with a K3 screw - suggestions needed (Doug Faunt N6TQS +1-510-717-1197) 12. Re: Problem with a K3 screw - suggestions needed (Ken Chandler) 13. Re: KPA500 PWR Display (Ken K3IU) 14. Re: KPA500 PWR Display (Jack Brindle) 15. Re: Fwd: KX3 Micro Manual Available in Apple App Store from Elecraft Digest, Vol 103, Issue 32 (Mike KS7D) 16. Re: Fwd: KX3 Micro Manual Available in Apple App Store from Elecraft Digest, Vol 103, Issue 32 (Chip Stratton) 17. Re: KPA500 PWR Display (Ken K3IU) 18. Reflector postings (khal...@aol.com) 19. Re: Price guesstimate on KXPA100 (Wayne Burdick) 20. Re: Fwd: KX3 Micro Manual Available in Apple App Store from Elecraft Digest, Vol 103, Issue 32 (Richard Gillingham) 21. Re: Reflector postings (Don Wilhelm) 22. K3 near salt water (Robert Fanfant) 23. Re: K3 near salt water (W4GRJ) 24. Re: K3 near salt water (Eric Swartz - WA6HHQ, Elecraft) 25. Re: K3 near salt water (Don Wilhelm) 26. Re: K3 near salt water (Ken G Kopp) 27. Re: K3 near salt water (Mike Harris) 28. Long Messages (David Dunn) 29. Rigblaster Plus with Elecraft K3 (Alfredo V?lez WP3C) 30. Re: Long Messages (K2GN) 31. Re: K3 near salt water (W4GRJ) 32. Re: Long Messages (Phil Kane) -- Message: 1 Date: Thu, 27 Dec 2012 12:07:39 -0500 (EST) From: ac...@aol.com To: elecraft@mailman.qth.net Subject: [Elecraft] KPA500 PWR Display Message-ID: <2535.60515ac3.3e0dd...@aol.com> Content-Type: text/plain; charset="US-ASCII" I like to have the KPA500 display set to constantly show the PWR output. I just noticed that when I swtich bands from my K3, the KPA500 display stays set to display PWR output, but when I switch bands on the KPA500, the display always goes back to display the band. Then I always have to press PWR again to display the PWR output. Is there any way to keep the KPA500 display "stuck" on PWR output when changing bands directly from the KPA500 keypad? Mike -- Message: 2 Date: Thu, 27 Dec 2012 17:21:46 + From: Ian White GM3SEK To: elecraft@mailman.qth.net Subject: Re: [Elecraft] Problem with a K3 screw - suggestions needed Message-ID: Content-Type: text/plain;charset=us-ascii;format=flowed In Europe, make sure you are not using a Pozidriv screwdriver. A Pozidriv #1 screwdriver will kind-of work with the Phillips screws in the K3... right up to the moment when a screw gets stuck. Beyond that moment, a Pozidriv screwdriver is very likely to do damage. Even with a good-quality Phillips #1 driver, my 700-series K3 is now on its second set of case screws. The originals were worn out by opening up the K3 to show it to people :-) 73 from Ian GM3SEK http://www.ifwtech.co.uk/g3sek Tom H Childers wrote: Good advice Don. Another thing that will destroy Phillips head screws is the use of a reed and prince screw driver, so verify that you are REALY using a Phillips screw driver. The very tip of a Phillips screw driver is blunt, not sharp, but a reed and prince screw driver (which looks very much like a Phillips) is sharp on the tip and will not seat completely in a Phillips screw, thus slipping and destroying the socket. Beware when buying inexpensive screw drivers that are call Phillips screw drivers. Check the tip and make sure it's not sharp. 73, Tom Amateur Radio Operator N5GE ARRL Lifetime Member QCWA Lifetime Member On Wed, 26 Dec 2012 18:15:05 -0500, Don Wilhelm wrote: Fabio, That screw in into a 2D connector. You will be able to remove the front panel by removing the other 2 screws in the 2D connector, and then
Re: [Elecraft] RX IQ sound card problems KX3
Tabb. You are seeing images. That is a result of either imbalance in your soundcard gain settings for the I and Q settings or a failure ot the application to adjust for those images. If you are using NaP3 as your application, there are steps you can take to detect and cancel the images - tune to a strong signal and the cancellation process is automatic. I refer you to the archives on LP-Pan Yahoo group for more information. Most of the information on NaP3 and PowerSDR-IF can be found there. 73, Don W3FPR On 1/11/2013 11:10 PM, W9TTW Tabb Adams wrote: Hey I got it figured out just needed a isolator between the radio and computer. I do have one question on the scope I see the same signals up and down from the center frequency. One in upper side band and one in lower side band. Do I have a setting wrong in the option menu? __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Hey I got it figured out just needed a isolator between the radio and computer. I do have one question on the scope I see the same signals up and down from the center frequency. One in upper side band and one in lower side band. Do I have a setting wrong in the option menu? Sent from my iPad On Jan 11, 2013, at 7:19 PM, "Peter Eijlander (PA0PJE) [via Elecraft]" wrote: > OK, I don't understand the "digital modes" you are talking about. That > has nothing to do with SDR via the I/Q output. I'm afraid I can't help > you further with this. > > 73, > Peter - PA0PJE > > W9TTW Tabb Adams schreef: > > Right I just have the RX IQ plugged into the sound card not both, strange > > that I don't have problem when I am just using it for digital modes. Just > > got another email that another ham was having the same problem. > > > > Sent from my iPad > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > > If you reply to this email, your message will be added to the discussion > below: > http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568571.html > To unsubscribe from RX IQ sound card problems KX3, click here. > NAML - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568581.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 digital
I've only had my KX3 for a month. I tried for a week to make a contact without success. I was really getting frustrated. As it turned out, I was in PSK D mode rather than Data A. Once I figured out that mistake, everything was fine after that. Chris AB3QV On Fri, Jan 11, 2013 at 4:44 PM, wrote: > I have had my KX3 about a month now. I have never worked digital modes > before. It sounded very easy in the manual. So I listened to a few PSK31 > stations. Wow you have to read fast! I hear CQ's and try to reply. No > luck! Try > a few CQ's myself. No replies. I must be doing something wrong. I don't > have > any trouble making contacts on CW. I tried both 40 and 20 meters. Help! > 72 George/W2BPI > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 digital
George, Before you become discouraged, let me clue you in on a fairly common, yet silly, problem. Make sure your sound card is set up and calibrated so that you are receiving and then transmitting on the same frequency. I have seen a number of locals have this problem of actually operating split and not know it. What will happen is that the station you are answering will not hear you as you won't be on his frequency. My AC97 in my laptop has that problem, for instance. Have a look and best of luck. 73, Barry K3NDM - Original Message - From: w2b...@aol.com To: Elecraft@mailman.qth.net Sent: Friday, January 11, 2013 4:44:14 PM Subject: [Elecraft] KX3 digital I have had my KX3 about a month now. I have never worked digital modes before. It sounded very easy in the manual. So I listened to a few PSK31 stations. Wow you have to read fast! I hear CQ's and try to reply. No luck! Try a few CQ's myself. No replies. I must be doing something wrong. I don't have any trouble making contacts on CW. I tried both 40 and 20 meters. Help! 72 George/W2BPI __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 digital
I have done most of my QSOs on PSK31 and 5 watts. They include 49 states (still missing Rhode Island), and about 16 DXCC entities including Japan, Cuba, Brasil, and Australia. You can have a lot of fun with 5 watts, and with QRP you'll have stories about the ones that got away. Don's advice about narrowing your bandwidth is very good advice. I generally use the HI/Low bandwidth adjustments on my K3 to narrow the bandwidth around the station I am trying to contact until my 250Hz filter kicks in. (I lock the K3 VFO to avoid bumping it and moving the station on my computer waterfall.) Your KX3 has similar controls for the DSP bandwidth. I find my dynamic range limit is in the audio interface to the computer, and narrowing the bandwidth in the DSP gets rid of most of the other stations which overload the computer sound input. Have fun with the digital modes. Cheers - Bill, AE6JV On 1/11/13 at 3:13 PM, n...@hotmail.com (Ariel Jacala) wrote: 5 watts on PSK will work if you are in an empty section on the waterfall. In a crowded situation with strong signals nearby, you will be stepped on and obliterated by the strong signal. Certain DX stations are notorious for overdriving the waterfall and wiping out other signals. You are better off calling CQ in location away from nearby strong signals. At 5 watts your printing on the waterfall can be faint depending on propagation. I did get Hawaii once on PSK with my K2. My luck with PSK has always been better at 25-30 watts. That is just the nature of this mode. At QRP power, CW is much more efficient. Make sure you have enough drive to just trigger the ALC circuit. You are also better off decoding the PSK signal with Fldigi or DM780 - just a better PSK experience with the macros and all. --- Bill Frantz|Security, like correctness, is| Periwinkle (408)356-8506 |not an add-on feature. - Attr-| 16345 Englewood Ave www.pwpconsult.com |ibuted to Andrew Tanenbaum| Los Gatos, CA 95032 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] What CW Filters do others have
I am impressed with the turn around time at Elecraft! I ordered the parts on Saturday night and they were at my door step Tuesday when I got home from work. I ordered the internal antenna tuner and the 400hz 8 pole cw filter. I was in and out of the K3 with the new parts in 30 minutes. After some updates to the rig's software I was off and running. My impressions of the 400hz filter are high! it really "hugs" the signal and cuts out background band noise. Its amazing the stark difference when I open the width up from 400hz to 450hz. I am very glad I made the choice to get this filter! 73! AC8JD -- View this message in context: http://elecraft.365791.n2.nabble.com/What-CW-Filters-do-others-have-tp7568250p7568577.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 KSB2 help please
Keith, That is good news. Enjoy. 73, Don W3FPR On 1/11/2013 7:34 PM, N8CEP wrote: Don - thanks for your help. My new Microcontroller U1 and new ceramic resonator Z1 arrived in the mail this afternoon. Installed them tonight and everything works! Must remember to be more careful with static precautions in the future! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K2 KSB2 help please
Don - thanks for your help. My new Microcontroller U1 and new ceramic resonator Z1 arrived in the mail this afternoon. Installed them tonight and everything works! Must remember to be more careful with static precautions in the future! 73 Keith N8CEP -- View this message in context: http://elecraft.365791.n2.nabble.com/K2-KSB2-help-please-tp7568383p7568575.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Right I understand that part I only use the phones connection for digital modes may try an isolator thanks. Sent from my iPad On Jan 11, 2013, at 7:17 PM, "Don Wilhelm-4 [via Elecraft]" wrote: > Tabb, > > You may have to use isolation transformers (galvanic isolators) in the I > and Q lines between the KX3 and the soundcard. > The I and Q outputs are not at a high enough level for use on digital > modes, the headphone output is usually necessary to adequately > illuminate a waterfall display. > > 73, > Don W3FPR > > On 1/11/2013 7:10 PM, W9TTW Tabb Adams wrote: > > Right I just have the RX IQ plugged into the sound card not both, strange > > that I don't have problem when I am just using it for digital modes. Just > > got another email that another ham was having the same problem. > > > > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > > If you reply to this email, your message will be added to the discussion > below: > http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568570.html > To unsubscribe from RX IQ sound card problems KX3, click here. > NAML - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568574.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Sorry just stating that when I use the output from the phones connection on the KX3 into the line in on the sound card I don't have the hum, just when I plug the RX IQ inTo the line in on the sound card Sent from my iPad On Jan 11, 2013, at 7:19 PM, "Peter Eijlander (PA0PJE) [via Elecraft]" wrote: > OK, I don't understand the "digital modes" you are talking about. That > has nothing to do with SDR via the I/Q output. I'm afraid I can't help > you further with this. > > 73, > Peter - PA0PJE > > W9TTW Tabb Adams schreef: > > Right I just have the RX IQ plugged into the sound card not both, strange > > that I don't have problem when I am just using it for digital modes. Just > > got another email that another ham was having the same problem. > > > > Sent from my iPad > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > > If you reply to this email, your message will be added to the discussion > below: > http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568571.html > To unsubscribe from RX IQ sound card problems KX3, click here. > NAML - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568573.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 digital
It used to be that 5 watts on PSK31 was all that was needed, most all operators were using low power because it worked well. Most advice was to keep the power low - below 20 watts if I recall. As time went by, the power levels used on PSK31 have crept up and many operators are now using 100 watts or more. That kind of power in the narrow bandwidth of common PSK wattering holes will take over the AGC in the receiver because most are using bandwidths of 2.5 kHz or greater to see the full waterfall display. The AGC will respond to the strongest signal within the filter bandwidth and will make weaker stations more difficult to copy. Sometimes turning off the AGC will help, but concentrating on the station you wish to copy and narrowing the IF filter bandwidth will help even more. If you only want to work one station, there is no need to see the entire PSK31 band. Narrow the receiver filter and use the VFO to tune the desired station to the center of the IF passband. 73, Don W3FPR On 1/11/2013 6:13 PM, Ariel Jacala wrote: 5 watts on PSK will work if you are in an empty section on the waterfall. In a crowded situation with strong signals nearby, you will be stepped on and obliterated by the strong signal. Certain DX stations are notorious for overdriving the waterfall and wiping out other signals. You are better off calling CQ in location away from nearby strong signals. At 5 watts your printing on the waterfall can be faint depending on propagation. I did get Hawaii once on PSK with my K2. My luck with PSK has always been better at 25-30 watts. That is just the nature of this mode. At QRP power, CW is much more efficient. Make sure you have enough drive to just trigger the ALC circuit. You are also better off decoding the PSK signal with Fldigi or DM780 - just a better PSK experience with the macros and all. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
OK, I don't understand the "digital modes" you are talking about. That has nothing to do with SDR via the I/Q output. I'm afraid I can't help you further with this. 73, Peter - PA0PJE W9TTW Tabb Adams schreef: Right I just have the RX IQ plugged into the sound card not both, strange that I don't have problem when I am just using it for digital modes. Just got another email that another ham was having the same problem. Sent from my iPad __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Tabb, You may have to use isolation transformers (galvanic isolators) in the I and Q lines between the KX3 and the soundcard. The I and Q outputs are not at a high enough level for use on digital modes, the headphone output is usually necessary to adequately illuminate a waterfall display. 73, Don W3FPR On 1/11/2013 7:10 PM, W9TTW Tabb Adams wrote: Right I just have the RX IQ plugged into the sound card not both, strange that I don't have problem when I am just using it for digital modes. Just got another email that another ham was having the same problem. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Right I just have the RX IQ plugged into the sound card not both, strange that I don't have problem when I am just using it for digital modes. Just got another email that another ham was having the same problem. Sent from my iPad On Jan 11, 2013, at 7:02 PM, "Peter Eijlander (PA0PJE) [via Elecraft]" wrote: > OK, so I suppose when you move the line-in level to zero the noise from > the computer speakers go to zero as well. > > Check if not by mistake the microphone is used as input for HDSDR. > > You cannot use the phones output in combination with HDSDR, the program > expects the I and Q sigs on the respective left and right channels of > the sound card's line input. The output from HDSDR should then in turn > be routed to the computer's speakers. In fact the line input also > affects the reading on the S-meter in HDSDR. > > The large "carrier" looks to me as the hum you describe, for that would > be seen as a carrier close to the center frequency displayed. > > If you unplug the I/Q output on the KX3 and touch the tip or ring on the > plug you should be able to see and hear that action in HDSDR. > > 73, > Peter - PA0PJE > > W9TTW Tabb Adams schreef: > > Yep it is on in the menu, when I bring up the display on HDSDR there > > is a large carrier in the center of the display same noise I am > > hearing when I plug the RX IQ into the sound card. Strange thing is > > when I just use the phones output from the KX3 I don't get the noise > > just when I plug into the RX IQ port. I can work digital modes just > > fine with no noise. > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > > If you reply to this email, your message will be added to the discussion > below: > http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568568.html > To unsubscribe from RX IQ sound card problems KX3, click here. > NAML - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568569.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
OK, so I suppose when you move the line-in level to zero the noise from the computer speakers go to zero as well. Check if not by mistake the microphone is used as input for HDSDR. You cannot use the phones output in combination with HDSDR, the program expects the I and Q sigs on the respective left and right channels of the sound card's line input. The output from HDSDR should then in turn be routed to the computer's speakers. In fact the line input also affects the reading on the S-meter in HDSDR. The large "carrier" looks to me as the hum you describe, for that would be seen as a carrier close to the center frequency displayed. If you unplug the I/Q output on the KX3 and touch the tip or ring on the plug you should be able to see and hear that action in HDSDR. 73, Peter - PA0PJE W9TTW Tabb Adams schreef: Yep it is on in the menu, when I bring up the display on HDSDR there is a large carrier in the center of the display same noise I am hearing when I plug the RX IQ into the sound card. Strange thing is when I just use the phones output from the KX3 I don't get the noise just when I plug into the RX IQ port. I can work digital modes just fine with no noise. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Yep it is on in the menu, when I bring up the display on HDSDR there is a large carrier in the center of the display same noise I am hearing when I plug the RX IQ into the sound card. Strange thing is when I just use the phones output from the KX3 I don't get the noise just when I plug into the RX IQ port. I can work digital modes just fine with no noise. Sent from my iPad On Jan 11, 2013, at 6:37 PM, "Peter Eijlander (PA0PJE) [via Elecraft]" wrote: > OK, and did you switch on the RX I/Q option in the menu to: ON? > > What do you see on the spectrum and waterfall display in HDSDR? > > I have HDSDR too, not yet with the KX3 (but will be soon...:-) and I use > that currently with a Softrock mixer on 30 meters with a laptop (W7) and > an X-Fi usb soundcard. Works great there but you need to pay attention > to all settings in HDSDR like choosing the correct soundcard audio > (line)input. > > 73, > Peter - PA0PJE > > W9TTW Tabb Adams schreef: > > HDSRD SOFTWARE > > > > > > Sent from my iPad > > > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > > If you reply to this email, your message will be added to the discussion > below: > http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568566.html > To unsubscribe from RX IQ sound card problems KX3, click here. > NAML - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568567.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
OK, and did you switch on the RX I/Q option in the menu to: ON? What do you see on the spectrum and waterfall display in HDSDR? I have HDSDR too, not yet with the KX3 (but will be soon...:-) and I use that currently with a Softrock mixer on 30 meters with a laptop (W7) and an X-Fi usb soundcard. Works great there but you need to pay attention to all settings in HDSDR like choosing the correct soundcard audio (line)input. 73, Peter - PA0PJE W9TTW Tabb Adams schreef: HDSRD SOFTWARE Sent from my iPad __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] P3 Freeze.
We've identified an issue that can sometimes cause the SVGA to freeze when the encoder on the P3 is moved very rapidly. We are working on a solution. 73, Paul -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-Freeze-tp7568550p7568565.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
HDSRD SOFTWARE Sent from my iPad On Jan 11, 2013, at 6:12 PM, "Peter Eijlander (PA0PJE) [via Elecraft]" wrote: > Hi Tabb, > > What SDR software do you use to run the I/Q output with? > > 73, > Peter - PA0PJE > > W9TTW Tabb Adams schreef: > > Having a problem with the RX IQ output every time I plug into the sound > > card > > I get a hum or buzz. Input is stereo on the sound card. Do not have the > > same > > problems when I input from phones to input in sound card for digital mode > > work. Sound card is a creative x-fi 1090 thanks for any help! > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:[hidden email] > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > > > If you reply to this email, your message will be added to the discussion > below: > http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568562.html > To unsubscribe from RX IQ sound card problems KX3, click here. > NAML - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561p7568564.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 digital
5 watts on PSK will work if you are in an empty section on the waterfall. In a crowded situation with strong signals nearby, you will be stepped on and obliterated by the strong signal. Certain DX stations are notorious for overdriving the waterfall and wiping out other signals. You are better off calling CQ in location away from nearby strong signals. At 5 watts your printing on the waterfall can be faint depending on propagation. I did get Hawaii once on PSK with my K2. My luck with PSK has always been better at 25-30 watts. That is just the nature of this mode. At QRP power, CW is much more efficient. Make sure you have enough drive to just trigger the ALC circuit. You are also better off decoding the PSK signal with Fldigi or DM780 - just a better PSK experience with the macros and all. Ariel NY4G Sent from my iPad On Jan 11, 2013, at 4:44 PM, w2b...@aol.com wrote: > I have had my KX3 about a month now. I have never worked digital modes > before. It sounded very easy in the manual. So I listened to a few PSK31 > stations. Wow you have to read fast! I hear CQ's and try to reply. No luck! > Try > a few CQ's myself. No replies. I must be doing something wrong. I don't have > any trouble making contacts on CW. I tried both 40 and 20 meters. Help! > 72 George/W2BPI > __ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] RX IQ sound card problems KX3
Hi Tabb, What SDR software do you use to run the I/Q output with? 73, Peter - PA0PJE W9TTW Tabb Adams schreef: Having a problem with the RX IQ output every time I plug into the sound card I get a hum or buzz. Input is stereo on the sound card. Do not have the same problems when I input from phones to input in sound card for digital mode work. Sound card is a creative x-fi 1090 thanks for any help! __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] RX IQ sound card problems KX3
Having a problem with the RX IQ output every time I plug into the sound card I get a hum or buzz. Input is stereo on the sound card. Do not have the same problems when I input from phones to input in sound card for digital mode work. Sound card is a creative x-fi 1090 thanks for any help! - Tabb W9TTW -- View this message in context: http://elecraft.365791.n2.nabble.com/RX-IQ-sound-card-problems-KX3-tp7568561.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] Kx3: How to interface UP, DOWN and PTT signal ?
Look on the Elecraft web site under manuals then KX3. There is an instruction sheet for the MH3 posted there which shows a schematic. Lou W2ROW Brian Lodahl wrote > Hi, > > [ Reposting in seperate thread ] > > For the 4-pin mic pinout for the MH-3 microphone, it is listed that the > PTT line also carries logic for UP and DOWN keys. > > > Would it be possible to ask for a schematic ? > > 73' > Brian OZ2BRN > Kx3 # 1118, K2 # 6936 -- View this message in context: http://elecraft.365791.n2.nabble.com/Kx3-How-to-interface-UP-DOWN-and-PTT-signal-tp7568557p7568560.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] P3 Freeze.
I have experienced this, but my lock-ups occur when tapping the SELECT button and using the knob on the P3 to QSY to a frequency on the SVGA display. It's never stopped doing that, so now as a work-around, I tap the FINE button on the right of the main VFO knob with my social finger and use the VFO to make rapid changes on the SVGA screen. Tapping it again returns it to 1Hz resolution for fine tuning. On Fri, 11 Jan 2013 09:44:24 -0800 (PST), Tom Fitzpatrick wrote: > My P3 display periodically freezes. I've run a couple of contests with it >going and it seems fine, but every once in awhile, it will just lock up. I >turn it off and back on and it's ok. Any ideas?? > > >Tom, K4IE >__ >Elecraft mailing list >Home: http://mailman.qth.net/mailman/listinfo/elecraft >Help: http://mailman.qth.net/mmfaq.htm >Post: mailto:Elecraft@mailman.qth.net > >This list hosted by: http://www.qsl.net >Please help support this email list: http://www.qsl.net/donate.html 73, Tom Amateur Radio Operator N5GE ARRL Lifetime Member QCWA Lifetime Member __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] P3 Freeze.
Hi Tom, This has happened to me on two or three occasions. It never happened before I installed the SVGA board. But of course after the SVGA installation the firmware has gone through one or two revisions. I think it happened going from transmit to receive. Mine also cleared up with a quick cycling of the P3 power button. 73, Mike K2MK Tom-2 wrote > My P3 display periodically freezes. I've run a couple of contests > with it going and it seems fine, but every once in awhile, it will just > lock up. I turn it off and back on and it's ok. Any ideas?? > > Tom, K4IE -- View this message in context: http://elecraft.365791.n2.nabble.com/P3-Freeze-tp7568550p7568558.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Kx3: How to interface UP, DOWN and PTT signal ?
Hi, [ Reposting in seperate thread ] For the 4-pin mic pinout for the MH-3 microphone, it is listed that the PTT line also carries logic for UP and DOWN keys. As I want to interface using a Heil Traveller headset, which has the UP and DOWN key signals on a seperate line (8-pin round standard), how are the logics defined for this pin (first ring on the 4-pin jack) on the Kx3 and MH-3, respectively ? Would it be possible to ask for a schematic ? 73' Brian OZ2BRN Kx3 # 1118, K2 # 6936 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] KX3 digital
I have had my KX3 about a month now. I have never worked digital modes before. It sounded very easy in the manual. So I listened to a few PSK31 stations. Wow you have to read fast! I hear CQ's and try to reply. No luck! Try a few CQ's myself. No replies. I must be doing something wrong. I don't have any trouble making contacts on CW. I tried both 40 and 20 meters. Help! 72 George/W2BPI __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] Kx3: How to interface UP, DOWN and PTT signal ?
Hi, For the 4-pin mic pinout for the MH-3 microphone, it is listed that the PTT line also carries logic for UP and DOWN keys. As I want to interface using a Heil Traveller headset, which has the UP and DOWN key signals on a seperate line (8-pin round standard), how are the logics defined for this pin (first ring on the 4-pin jack) on the Kx3 and MH-3, respectively ? Would it be possible to ask for a schematic ? 73' Brian OZ2BRN __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Sub Receiver Problems
Or email k3supp...@elecraft.com 73, Eric --- www.elecraft.com On 1/11/2013 10:09 AM, Guy Olinger K2AV wrote: You need to call Elecraft Tech Support on this problem before you go further. They don't live on the reflector. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Sub Receiver Problems
You need to call Elecraft Tech Support on this problem before you go further. They don't live on the reflector. Someone knowledgeable can walk you through a series of steps to isolate what is going on. There are too many possibilities to work this efficiently over email. Do not go soldering things until you have called Elecraft. It could easily be something you misread in the manual, or a misconception about how it works with the components you have. Or it can be an improperly seated tiny plug on those coax leads. Everyone has done that. There is a certain "feel" to it when it is really seated. Frankly 9 S units usually means that something is not connected at all. 9 S units down means all you are hearing is capacitive coupling. BOTH the cable connections AND the state of the RX hold button must match. But there is a pile of possibilities. Call Elecraft and have them walk you through. 73, Guy. On Thu, Jan 10, 2013 at 11:32 PM, KGØUS wrote: > > > "That's why I took the effort to measure the resistors. R43 is 51 Ohm, R37 > and R45 are both 63 Ohm." > > From what you measured above, I can tell you that your R43, R37, and R45 > resistors are all good. > > Please take a closer look at the schematic. When you measure R43, you are > actually measuring R43 in parallel with R37 and R45 in series. This would > be 68 || (100 + 100) = 50.74 Ohms. > > When you measure R37 or R45, you are actually measuring 100 || (68 + 100) = > 62.68 Ohms. > > I plan to make a few more measurements this weekend and was hoping for some > guidance from the experts. I have been getting the cold shoulder here. > > I will make a few more measurements here but I have limited resources at > home. I have unlimited resources at work but I am not allowed to work on > home equipment. > > I have four choices: > 1.) Try to fix it myself but I will need to ask a friend if I can use his > surface mount solder station. > 2.) Do nothing, remove it, or live with it. > 3.) By another subreceiver kit for $600. > 4.) Send it in for repair. > > Good luck, > > Dave KG0US > > > > > > -- > View this message in context: > http://elecraft.365791.n2.nabble.com/K3-Sub-Receiver-Problems-tp7568116p7568540.html > Sent from the Elecraft mailing list archive at Nabble.com. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] P3 Freeze.
You must check serial cable. Edu YY4GMJ On Fri, Jan 11, 2013 at 1:14 PM, Tom Fitzpatrick wrote: > My P3 display periodically freezes. I've run a couple of contests with > it going and it seems fine, but every once in awhile, it will just lock up. > I turn it off and back on and it's ok. Any ideas?? > > > Tom, K4IE > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] FS Begali Paddles for your Elecraft station
Hi, I am downsizing my collection of Morse code equipment. I have forsale a very nice Begali Signature Edition paddle key for your K3 or K2 at hour home station. I am asking $270 USD, shipped free via USPS Priority Mail within CONUS. If anyone is interested in more info. Please take a look here: http://kr7w.blogspot.com/2013/01/begali-signature-paddles-for-sale.html For questions or more info. Please email me off of the list. Regards, Rich KR7W KX3 nr 1588 __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] P3 Freeze.
My P3 display periodically freezes. I've run a couple of contests with it going and it seems fine, but every once in awhile, it will just lock up. I turn it off and back on and it's ok. Any ideas?? Tom, K4IE __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] New Output Power Issue
All, Thanks for the input. Glad the K3 seems to be operating up to snuff. I now consider this issue closed. 73 and have a great weekend. --Ian Ian Kahn, KM4IK Roswell, GA EM74ua km4ik@gmail.com K3 #281, P3 #688 HRD v5.x/6.0 Test Team On Thu, Jan 10, 2013 at 11:27 PM, Don Wilhelm wrote: > Ian, > > So your K3 is operating a bit more efficiently than average - what is to > be worried about, be glad. > > 73, > Don W3FPR > > > On 1/10/2013 10:23 PM, Ian Kahn - Ham wrote: > >> So, several weeks after originally starting this thread, I finally had >> time this evening to sit down and take some voltage and current >> measurements. I used my Astron SS-30 power supply connected to the 40A >> DC-in port on my Rigrunner. I then ran the Elecraft power cord from a 25A >> port on the Rigrunner into the 12V DC-in on the back of the K3. Everything >> measures 13.8V in standy/rx, all the way to the reading on the K3 display, >> with the K3 showing .82A current draw in rxv. I would measure the power at >> the 12V in port on the K3, but can't see a way to get the probes into the >> powerpole connectors without damaging anything. I ran my tests using FSK-D >> at 100W and into a known-good 300W dummy load, so I could get 100% duty >> cycle for a few seconds with each transmit. When I go to transmit, voltage >> on every band looks good, with the voltage dropping from 13.8V to anywhere >> from 12.1 to 12.4 volts. I'm concerned about some of the current readings, >> however. 80 meters shows a current draw of 15.80A; 17 meters shows a draw >> of 16.35A; 15 meters shows a draw of 16.40A; 10 meters shows a draw of >> 12.93A. 12m, 20m, 30m, 40m, and 160m are all within the 17-22A current >> draw rating for the K3. The RF output meter on the K3 shows 100w out on >> every band, but I haven't put the rig on an external watt meter. Since >> these are all below the nominal current draw given in the K3 owner's manual >> (17-22A), is there something I should look at recalibrating? Or could >> something more serious be going here that I need to be concerned about? >> Or, am I worried about nothing? Further guidance is greatly appreciated. >> >> > -- __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] W3PFR/N0SS audio output board for K2 wanted
I've tried direction connections, but find I'm getting feedback on the higher bands. Does anyone have an excess W3FPR/N0SS circuit board for the buffered K2 audio output? Will pay a reasonable price ! Chris NQ0Z -- View this message in context: http://elecraft.365791.n2.nabble.com/W3PFR-N0SS-audio-output-board-for-K2-wanted-tp7568548.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] FS: K60XV 60-M and transverter adapter - new unbuilt kit
Hello Group, The K60XV adds 60-m ham-band coverage to K2. In addition, it provides a low level split-path interface for use with transverters. I bought this kit last month but have no time to build. It is an unbuilt brand new kit. My price is US$80 including shipping to US and major cities in Europe by airmail. If you are interested, please reply off-the-list. TNX & 73, Johnny VR2XMC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KX3 VOX in data mode
But surely in Data D mode, the psk or rtty is being internally generated within the K3 - any audio input allowable by having the VOX tripped would be irrelevant anyway. In practice there is no Data D mode - just PSK-D and RTTY-D? Unless I have misunderstood the original question of course :-) 73 Stephen G4SJP On 10 January 2013 23:22, K7JLTextra wrote: > I will try again, did not work the first time I tried it. Needs to be > added to the manual. > > John Hendricks K7JLT > > On Jan 10, 2013, at 14:46, Chuck Shefflette - AA3CS wrote: > > > VOX works fine in Data A mode, not at all in Data D mode. > > > > 73, > > Chuck - AA3CS > > > > Sent from my iPad > > > > On Jan 10, 2013, at 15:57, K7JLTextra wrote: > > > >> If the VOX could be used in data modes it would greatly simplify the > computer interface. Is there something here I am missing? > >> > >> John Hendricks K7JLT > >> __ > >> Elecraft mailing list > >> Home: http://mailman.qth.net/mailman/listinfo/elecraft > >> Help: http://mailman.qth.net/mmfaq.htm > >> Post: mailto:Elecraft@mailman.qth.net > >> > >> This list hosted by: http://www.qsl.net > >> Please help support this email list: http://www.qsl.net/donate.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] (OT) HRD Remote Server on WIN7
Works fine as well as on Windows 8. -- View this message in context: http://elecraft.365791.n2.nabble.com/OT-HRD-Remote-Server-on-WIN7-tp7568512p7568545.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html