[Elecraft] K3 Auto antenna switching
Thanks, Fred. I switched DIGOUT1 on while on 6m and it remembers to be on, only on 6m. My application will be to control an external relay that will enable INHIBIT for 6m-eme. As already mentioned, I use BAND0 for this on 2m and higher transverter bands, but I do not want INHIBIT for normal 6m use, only to sequence my TR relay and Harris 900w 6m PA, when using it. Applying RF drive without a load on the Harris can destroy the amp. One does not want to hot-switch the coax relay as 900w courses thru it! So you can add another use for DIGOUT! I am getting close to first smoke with the 6m QRO. 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 50-1.1kw?, 144-1.4kw, 432-100w, 1296-60w, 3400-? DUBUS Magazine USA Rep dubus...@gmail.com == __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Auto antenna switching
To play one-up with Don (not really): I have recently re-drawn my station block diagram to reflect the selling of my FT-847 and addition of more transverters to the K3. Coax switching is manual, except for the 1P6T XVT-Rx selection. The FT-817 shown at the bottom could become a KX3? http://www.kl7uw.com/2011_Station_2.jpg 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 50-1.1kw?, 144-1.4kw, 432-100w, 1296-60w, 3400-? DUBUS Magazine USA Rep dubus...@gmail.com == __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Dröse dro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From: dbellw...@aol.com To: elecraft@mailman.qth.net Cc: k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Guy, DigOut 1 is a per-band/per-antenna output. The user can program it On for one antenna and off for the other ... 73, ... Joe, W4TV On 8/25/2011 4:04 AM, Guy Olinger K2AV wrote: I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Drösedro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From:dbellw...@aol.com To:elecraft@mailman.qth.net Cc:k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Hi Guy and all, You could kind of do this with the DIGOUT1 signal from the ACC connector. It can be programmed OFF (floating, open-drain output, you need a pull up if you want a high) or ON (pulled down to ground). The Elecraft Owner's manual describes it on page 55 and here is what the KE7X K3 book says: (Figure 7 16.) This output signal is a general-purpose, open-drain output that may be programmed (OFF = floating, ON = pulled down to ground) on a per-band and a per-antenna basis (if the KAT3 ATU is installed). For example, you might use this feature to turn on the PR6 six meter preamp only when the six meter band and the six meter antenna are selected. To program DIGOUT1, tune the K3 Main receiver to the desired band with the selected antenna and go to CONFIG:DIGOUT1 and set it to ON. The maximum sinking current is 250 mA and the maximum load voltage is 25 VDC. So, kind of means you could program DIGOUT1 to be ON (pulled low) when you are on 80 and have ANT2 (for example) selected. For any other combination of band/ant DIGOUT1 would be floating (or pulled up). This would work if you are using an external band decoder to select antennas and you simply want to activate another switch or relay to switch in one of two 80 meter antennas. Cheers and 73, Fred KE7X Fred Cady fcady at ieee dot org The Elecraft K3: Design, Configuration, and Operation www.ke7x.com -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft- boun...@mailman.qth.net] On Behalf Of Guy Olinger K2AV Sent: Thursday, August 25, 2011 2:05 AM To: Oliver Dröse Cc: elecraft@mailman.qth.net; dbellw...@aol.com; k...@aol.com Subject: Re: [Elecraft] K3 Auto antenna switching I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Dröse dro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From: dbellw...@aol.com To: elecraft@mailman.qth.net Cc: k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Auto antenna switching
I was looking at the ACC features and have a question about DIGOUT1. Does this feature have any use without the KAT3? I wonder if there is map for its output states by band (or how one does this - it would be handy for me to use this for 6m-eme to enable INHIBIT when on 6m). I currently use BAND0 enable INHIBIT for my other VHF/UHF bands (the HI biases a NPN relay driver in my station control box). 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 50-1.1kw?, 144-1.4kw, 432-100w, 1296-60w, 3400-? DUBUS Magazine USA Rep dubus...@gmail.com == __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Joe Fred, Hmm, I was somehow under the impression that was needed for something, but reading it all again from scratch, that is the digout0 which apparently only works in relation to some transverter function. Thanks all for the info. 73, Guy. On Thu, Aug 25, 2011 at 10:57 AM, Cady, Fred fc...@ece.montana.edu wrote: Hi Guy and all, You could kind of do this with the DIGOUT1 signal from the ACC connector. It can be programmed OFF (floating, open-drain output, you need a pull up if you want a high) or ON (pulled down to ground). The Elecraft Owner's manual describes it on page 55 and here is what the KE7X K3 book says: (Figure 7 16.) This output signal is a general-purpose, open-drain output that may be programmed (OFF = floating, ON = pulled down to ground) on a per-band and a per-antenna basis (if the KAT3 ATU is installed). For example, you might use this feature to turn on the PR6 six meter preamp only when the six meter band and the six meter antenna are selected. To program DIGOUT1, tune the K3 Main receiver to the desired band with the selected antenna and go to CONFIG:DIGOUT1 and set it to ON. The maximum sinking current is 250 mA and the maximum load voltage is 25 VDC. So, kind of means you could program DIGOUT1 to be ON (pulled low) when you are on 80 and have ANT2 (for example) selected. For any other combination of band/ant DIGOUT1 would be floating (or pulled up). This would work if you are using an external band decoder to select antennas and you simply want to activate another switch or relay to switch in one of two 80 meter antennas. Cheers and 73, Fred KE7X Fred Cady fcady at ieee dot org The Elecraft K3: Design, Configuration, and Operation www.ke7x.com -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft- boun...@mailman.qth.net] On Behalf Of Guy Olinger K2AV Sent: Thursday, August 25, 2011 2:05 AM To: Oliver Dröse Cc: elecraft@mailman.qth.net; dbellw...@aol.com; k...@aol.com Subject: Re: [Elecraft] K3 Auto antenna switching I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Dröse dro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From: dbellw...@aol.com To: elecraft@mailman.qth.net Cc: k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
The only official use right now is for turning the PR-6 on/off on six meters. 73, ... Joe, W4TV On 8/25/2011 2:02 PM, Guy Olinger K2AV wrote: Joe Fred, Hmm, I was somehow under the impression that was needed for something, but reading it all again from scratch, that is the digout0 which apparently only works in relation to some transverter function. Thanks all for the info. 73, Guy. On Thu, Aug 25, 2011 at 10:57 AM, Cady, Fredfc...@ece.montana.edu wrote: Hi Guy and all, You could kind of do this with the DIGOUT1 signal from the ACC connector. It can be programmed OFF (floating, open-drain output, you need a pull up if you want a high) or ON (pulled down to ground). The Elecraft Owner's manual describes it on page 55 and here is what the KE7X K3 book says: (Figure 7 16.) This output signal is a general-purpose, open-drain output that may be programmed (OFF = floating, ON = pulled down to ground) on a per-band and a per-antenna basis (if the KAT3 ATU is installed). For example, you might use this feature to turn on the PR6 six meter preamp only when the six meter band and the six meter antenna are selected. To program DIGOUT1, tune the K3 Main receiver to the desired band with the selected antenna and go to CONFIG:DIGOUT1 and set it to ON. The maximum sinking current is 250 mA and the maximum load voltage is 25 VDC. So, kind of means you could program DIGOUT1 to be ON (pulled low) when you are on 80 and have ANT2 (for example) selected. For any other combination of band/ant DIGOUT1 would be floating (or pulled up). This would work if you are using an external band decoder to select antennas and you simply want to activate another switch or relay to switch in one of two 80 meter antennas. Cheers and 73, Fred KE7X Fred Cady fcady at ieee dot org The Elecraft K3: Design, Configuration, and Operation www.ke7x.com -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft- boun...@mailman.qth.net] On Behalf Of Guy Olinger K2AV Sent: Thursday, August 25, 2011 2:05 AM To: Oliver Dröse Cc: elecraft@mailman.qth.net; dbellw...@aol.com; k...@aol.com Subject: Re: [Elecraft] K3 Auto antenna switching I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Drösedro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From:dbellw...@aol.com To:elecraft@mailman.qth.net Cc:k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
You speaking of digout0 or digout1? On Thu, Aug 25, 2011 at 2:10 PM, Joe Subich, W4TV li...@subich.com wrote: The only official use right now is for turning the PR-6 on/off on six meters. 73, ... Joe, W4TV On 8/25/2011 2:02 PM, Guy Olinger K2AV wrote: Joe Fred, Hmm, I was somehow under the impression that was needed for something, but reading it all again from scratch, that is the digout0 which apparently only works in relation to some transverter function. Thanks all for the info. 73, Guy. On Thu, Aug 25, 2011 at 10:57 AM, Cady, Fredfc...@ece.montana.edu wrote: Hi Guy and all, You could kind of do this with the DIGOUT1 signal from the ACC connector. It can be programmed OFF (floating, open-drain output, you need a pull up if you want a high) or ON (pulled down to ground). The Elecraft Owner's manual describes it on page 55 and here is what the KE7X K3 book says: (Figure 7 16.) This output signal is a general-purpose, open-drain output that may be programmed (OFF = floating, ON = pulled down to ground) on a per-band and a per-antenna basis (if the KAT3 ATU is installed). For example, you might use this feature to turn on the PR6 six meter preamp only when the six meter band and the six meter antenna are selected. To program DIGOUT1, tune the K3 Main receiver to the desired band with the selected antenna and go to CONFIG:DIGOUT1 and set it to ON. The maximum sinking current is 250 mA and the maximum load voltage is 25 VDC. So, kind of means you could program DIGOUT1 to be ON (pulled low) when you are on 80 and have ANT2 (for example) selected. For any other combination of band/ant DIGOUT1 would be floating (or pulled up). This would work if you are using an external band decoder to select antennas and you simply want to activate another switch or relay to switch in one of two 80 meter antennas. Cheers and 73, Fred KE7X Fred Cady fcady at ieee dot org The Elecraft K3: Design, Configuration, and Operation www.ke7x.com -Original Message- From: elecraft-boun...@mailman.qth.**netelecraft-boun...@mailman.qth.net[mailto: elecraft- boun...@mailman.qth.net] On Behalf Of Guy Olinger K2AV Sent: Thursday, August 25, 2011 2:05 AM To: Oliver Dröse Cc: elecraft@mailman.qth.net; dbellw...@aol.com; k...@aol.com Subject: Re: [Elecraft] K3 Auto antenna switching I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Drösedro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From:dbellw...@aol.com To:elecraft@mailman.qth.net Cc:k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecrafthttp://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htmhttp://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecrafthttp://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htmhttp://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __**__**__ Elecraft mailing list Home: http://mailman.qth.net/**mailman/listinfo/elecrafthttp://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.**htmhttp://mailman.qth.net/mmfaq.htm Post: mailto:elecr...@mailman.qth.**net Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
I'm speaking DIGOUT1. From: guyk...@gmail.com [mailto:guyk...@gmail.com] On Behalf Of Guy Olinger K2AV Sent: Thursday, August 25, 2011 12:24 PM To: Joe Subich, W4TV Cc: Cady, Fred; elecraft@mailman.qth.net; dbellw...@aol.com; k...@aol.com Subject: Re: [Elecraft] K3 Auto antenna switching You speaking of digout0 or digout1? On Thu, Aug 25, 2011 at 2:10 PM, Joe Subich, W4TV li...@subich.com wrote: The only official use right now is for turning the PR-6 on/off on six meters. 73, ... Joe, W4TV On 8/25/2011 2:02 PM, Guy Olinger K2AV wrote: Joe Fred, Hmm, I was somehow under the impression that was needed for something, but reading it all again from scratch, that is the digout0 which apparently only works in relation to some transverter function. Thanks all for the info. 73, Guy. On Thu, Aug 25, 2011 at 10:57 AM, Cady, Fredfc...@ece.montana.edu wrote: Hi Guy and all, You could kind of do this with the DIGOUT1 signal from the ACC connector. It can be programmed OFF (floating, open-drain output, you need a pull up if you want a high) or ON (pulled down to ground). The Elecraft Owner's manual describes it on page 55 and here is what the KE7X K3 book says: (Figure 7 16.) This output signal is a general-purpose, open-drain output that may be programmed (OFF = floating, ON = pulled down to ground) on a per-band and a per-antenna basis (if the KAT3 ATU is installed). For example, you might use this feature to turn on the PR6 six meter preamp only when the six meter band and the six meter antenna are selected. To program DIGOUT1, tune the K3 Main receiver to the desired band with the selected antenna and go to CONFIG:DIGOUT1 and set it to ON. The maximum sinking current is 250 mA and the maximum load voltage is 25 VDC. So, kind of means you could program DIGOUT1 to be ON (pulled low) when you are on 80 and have ANT2 (for example) selected. For any other combination of band/ant DIGOUT1 would be floating (or pulled up). This would work if you are using an external band decoder to select antennas and you simply want to activate another switch or relay to switch in one of two 80 meter antennas. Cheers and 73, Fred KE7X Fred Cady fcady at ieee dot org The Elecraft K3: Design, Configuration, and Operation www.ke7x.com -Original Message- From: elecraft-boun...@mailman.qth.net mailto:elecraft-boun...@mailman.qth.net [mailto:elecraft- boun...@mailman.qth.net] On Behalf Of Guy Olinger K2AV Sent: Thursday, August 25, 2011 2:05 AM To: Oliver Dröse Cc: elecraft@mailman.qth.net; dbellw...@aol.com; k...@aol.com Subject: Re: [Elecraft] K3 Auto antenna switching I would really like an external signal that tells whether ANT1 or ANT2 is selected. Any way to do that? 73, Guy On Wed, Aug 24, 2011 at 7:28 PM, Oliver Drösedro...@necg.de wrote: Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From:dbellw...@aol.com To:elecraft@mailman.qth.net Cc:k
Re: [Elecraft] K3 Auto antenna switching
HI Ed, You should be able to go into CONFIG: DIGOUT1 and then step through the bands to map out DIGOUT1 ON or OFF. It doesn't require the KAT3. 73, Fred Fred Cady fcady at ieee dot org The Elecraft K3: Design, Configuration and Operation www.ke7x.com -Original Message- From: elecraft-boun...@mailman.qth.net [mailto:elecraft- boun...@mailman.qth.net] On Behalf Of Edward R. Cole Sent: Thursday, August 25, 2011 12:01 PM To: Elecraft@mailman.qth.net Subject: [Elecraft] K3 Auto antenna switching I was looking at the ACC features and have a question about DIGOUT1. Does this feature have any use without the KAT3? I wonder if there is map for its output states by band (or how one does this - it would be handy for me to use this for 6m-eme to enable INHIBIT when on 6m). I currently use BAND0 enable INHIBIT for my other VHF/UHF bands (the HI biases a NPN relay driver in my station control box). 73, Ed - KL7UW, WD2XSH/45 == BP40IQ 500 KHz - 10-GHz www.kl7uw.com EME: 50-1.1kw?, 144-1.4kw, 432-100w, 1296-60w, 3400-? DUBUS Magazine USA Rep dubus...@gmail.com == __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Gotcha. Is what goes on with DIGOUT0 firmwired in the firmware, or is that available somehow with some sneaky procedure? TWO signals I could work, one of them via software command to K3, would be simply splendiferous and get rid of ugly relay logic board. But I know I'm reaching here... 73, Guy. On Thu, Aug 25, 2011 at 3:48 PM, Joe Subich, W4TV li...@subich.com wrote: DIGOUT1 - see the PR6 Owners Manual 73, ... Joe, W4TV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
E.g. does something else when KIO3 is set to NOR, besides stay high. On Thu, Aug 25, 2011 at 4:13 PM, Guy Olinger K2AV olin...@bellsouth.netwrote: Gotcha. Is what goes on with DIGOUT0 firmwired in the firmware, or is that available somehow with some sneaky procedure? TWO signals I could work, one of them via software command to K3, would be simply splendiferous and get rid of ugly relay logic board. But I know I'm reaching here... 73, Guy. On Thu, Aug 25, 2011 at 3:48 PM, Joe Subich, W4TV li...@subich.comwrote: DIGOUT1 - see the PR6 Owners Manual 73, ... Joe, W4TV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Guy, Thanks for your questions - you are giving me ideas about how to reconfigure and automate my antenna switching to take advantage of both ANT1 and ANT2. Right now, I use only a single connector on the KAT3, and have given up on automating the band selection for now, so I operate manual switches. I have 4 HF and 6 meter coax lines coming into the shack, and one of those comes from a remote 6 position antenna relay. Of course, my situation is a bit unique because once in the shack, I switch those 4 antenna feedlines among 3 transceivers. The K2 gets priority, the FT-847 is second priority and the 3rd transceiver can take whichever feedlines that are not being used by the other 2. An advantage of my arrangement is that when no feedline is selected (or relay power is off), the K3 and the FT-847 are connected to a dummy load (the 3rd transceiver operator has to remember to switch to a dummy load manually. On some bands (80, 40 and 20) , I have 3 antennas either up now or in my antenna plan, so that is why I have chosen the manual switching - automating it with only ANT1 or ANT2 was not sufficient, I have to figure out how to handle that. The ACC outputs from the KRC2 may be the answer, but selecting the correct ACC output is still a manual operation. 73, Don W3FPR On 8/25/2011 4:33 PM, Guy Olinger K2AV wrote: E.g. does something else when KIO3 is set to NOR, besides stay high. On Thu, Aug 25, 2011 at 4:13 PM, Guy Olinger K2AVolin...@bellsouth.netwrote: Gotcha. Is what goes on with DIGOUT0 firmwired in the firmware, or is that available somehow with some sneaky procedure? TWO signals I could work, one of them via software command to K3, would be simply splendiferous and get rid of ugly relay logic board. But I know I'm reaching here... 73, Guy. On Thu, Aug 25, 2011 at 3:48 PM, Joe Subich, W4TVli...@subich.comwrote: DIGOUT1 - see the PR6 Owners Manual 73, ... Joe, W4TV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
As far as I know the only use of DIGOUT 0 is to indicate low power operation for a given transverter band: With KIO3 set to TRN or HF-TRN, the DIGOUT0 line (ACC, pin 6) will output 0 V when low power mode is selected for the current transverter band (CONFIG:XVn PWR). At all other times, DIGOUT0 will be floating (Hi-Z). It would be nice if DIGOUT 0 could be used for other functions (e.g., per-band/per-mode like DIGOUT 1, or generate a 500 msec pulse in response to the ATU TUNE button when the KAT3 is off/not installed) if the K3 is not used with transverters. 73, ... Joe, W4TV On 8/25/2011 4:13 PM, Guy Olinger K2AV wrote: Gotcha. Is what goes on with DIGOUT0 firmwired in the firmware, or is that available somehow with some sneaky procedure? TWO signals I could work, one of them via software command to K3, would be simply splendiferous and get rid of ugly relay logic board. But I know I'm reaching here... 73, Guy. On Thu, Aug 25, 2011 at 3:48 PM, Joe Subich, W4TVli...@subich.com wrote: DIGOUT1 - see the PR6 Owners Manual 73, ... Joe, W4TV __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Auto antenna switching
I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Dave, The band data (when decoded) will allow you to connect both of your 80 meter antennas to the K3 - one to ANT1 and the other to ANT2 (assuming you have the KAT3 installed). Your external antenna switching relay system (working from the band data decode) is responsible for connecting the correct 80 meter antenna to ANT1 and the other one to ANT2. The relay system should connect both of them when you are on 80 meters. Then you use the K3 ANT button to switch between ANT1 and ANT2. The same system can be used to handle two antennas on any one band. It is all in the way you set up your band decoder and your antenna switching relay system - there are many possibilities, and will vary from one installation to another. 73, Don W3FPR On 8/24/2011 2:29 PM, dbellw...@aol.com wrote: I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Auto antenna switching
Hi Dave, unfortunately not, it's just one BCD code per band. 73, Olli - DH8BQA - Original Message - From: dbellw...@aol.com To: elecraft@mailman.qth.net Cc: k...@aol.com Sent: Wednesday, August 24, 2011 8:29 PM Subject: [Elecraft] K3 Auto antenna switching I have two 80 meter antennas. Is it possible to program the band data output on the K3 for 80 meters # 1 and # 2? I couldn't find an answer to this in the manual. 73, Dave __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html