Re: [Elecraft] K3 Parts transfer between rigs
I just received an email that the tech moved the DSP2 and SYN to 1526. I will email and call tech support to find out what is up. Keith AG6AZ -Original Message- From: Mike K2MK Sent: Friday, October 19, 2012 8:08 AM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] K3 Parts transfer between rigs Hi Keith, You should review the KRX3 assembly/installation manual. There's a resistor that may need to be modified (see page 21) and maybe some other stuff as well. 73, Mike K2MK Keith Heimbold wrote > I have sent my Elmer tech friend a couple emails asking him if he swapped > out the other boards. If he did not, we will have to get that done and see > if the errors are eradicated. This is a set back for sure but it gives me > an opportunity to better understand the K3 and its component parts. > > I will also contact tech support to see what is going on with the error > codes. It appears that I also received a ERR DVR error code to top it off > after I sent the email to the reflector. > > Keith > AG6AZ > > Sent from my iPhone please excuse typos > > On Oct 19, 2012, at 5:07 AM, "Don Wilhelm" < > w3fpr@ > > wrote: > >> Was the DSP2 board and the synthesizer board for the KRX3 transferred >> from the other K3. From the errors you are getting, it would seem that >> they were not. >> >> Did your tech elmer just do the unplugging/replugging job or did he check >> the result out after each option was transferred? What did he say when >> you asked him for his observations. >> >> You may have to contact Elecraft support with your error codes. >> >> 73, >> Don W3FPR -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Parts-transfer-between-rigs-tp7564314p7564329.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Parts transfer between rigs
Thanks for pointing that out. I will confer with my friend to see if he missed some of these steps or not. I am waiting to hear back from him. Keith AG6AZ Sent from my iPhone please excuse typos On Oct 19, 2012, at 8:09 AM, "Mike K2MK" wrote: > Hi Keith, > > You should review the KRX3 assembly/installation manual. There's a resistor > that may need to be modified (see page 21) and maybe some other stuff as > well. > > 73, > Mike K2MK > > > Keith Heimbold wrote >> I have sent my Elmer tech friend a couple emails asking him if he swapped >> out the other boards. If he did not, we will have to get that done and see >> if the errors are eradicated. This is a set back for sure but it gives me >> an opportunity to better understand the K3 and its component parts. >> >> I will also contact tech support to see what is going on with the error >> codes. It appears that I also received a ERR DVR error code to top it off >> after I sent the email to the reflector. >> >> Keith >> AG6AZ >> >> Sent from my iPhone please excuse typos >> >> On Oct 19, 2012, at 5:07 AM, "Don Wilhelm" < > >> w3fpr@ > >> > wrote: >> >>> Was the DSP2 board and the synthesizer board for the KRX3 transferred >>> from the other K3. From the errors you are getting, it would seem that >>> they were not. >>> >>> Did your tech elmer just do the unplugging/replugging job or did he check >>> the result out after each option was transferred? What did he say when >>> you asked him for his observations. >>> >>> You may have to contact Elecraft support with your error codes. >>> >>> 73, >>> Don W3FPR > > > > > > -- > View this message in context: > http://elecraft.365791.n2.nabble.com/K3-Parts-transfer-between-rigs-tp7564314p7564329.html > Sent from the Elecraft mailing list archive at Nabble.com. > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Parts transfer between rigs
Hi Keith, You should review the KRX3 assembly/installation manual. There's a resistor that may need to be modified (see page 21) and maybe some other stuff as well. 73, Mike K2MK Keith Heimbold wrote > I have sent my Elmer tech friend a couple emails asking him if he swapped > out the other boards. If he did not, we will have to get that done and see > if the errors are eradicated. This is a set back for sure but it gives me > an opportunity to better understand the K3 and its component parts. > > I will also contact tech support to see what is going on with the error > codes. It appears that I also received a ERR DVR error code to top it off > after I sent the email to the reflector. > > Keith > AG6AZ > > Sent from my iPhone please excuse typos > > On Oct 19, 2012, at 5:07 AM, "Don Wilhelm" < > w3fpr@ > > wrote: > >> Was the DSP2 board and the synthesizer board for the KRX3 transferred >> from the other K3. From the errors you are getting, it would seem that >> they were not. >> >> Did your tech elmer just do the unplugging/replugging job or did he check >> the result out after each option was transferred? What did he say when >> you asked him for his observations. >> >> You may have to contact Elecraft support with your error codes. >> >> 73, >> Don W3FPR -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Parts-transfer-between-rigs-tp7564314p7564329.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Parts transfer between rigs
I have sent my Elmer tech friend a couple emails asking him if he swapped out the other boards. If he did not, we will have to get that done and see if the errors are eradicated. This is a set back for sure but it gives me an opportunity to better understand the K3 and its component parts. I will also contact tech support to see what is going on with the error codes. It appears that I also received a ERR DVR error code to top it off after I sent the email to the reflector. Keith AG6AZ Sent from my iPhone please excuse typos On Oct 19, 2012, at 5:07 AM, "Don Wilhelm" wrote: > Was the DSP2 board and the synthesizer board for the KRX3 transferred from > the other K3. From the errors you are getting, it would seem that they were > not. > > Did your tech elmer just do the unplugging/replugging job or did he check the > result out after each option was transferred? What did he say when you asked > him for his observations. > > You may have to contact Elecraft support with your error codes. > > 73, > Don W3FPR > > On 10/19/2012 3:12 AM, Ham Radio wrote: >> I embarked on a project to move parts from one K3 to another and I got the >> rigs back from my tech elmer tonight. After getting the K3s home, I decided >> to follow the procedure to get them operating again. >> >> I had my tech elmer transfer the KAT3, KRX3, KDVR3 and KBF3 from one of the >> K3 to the other. I now have multiple errors and not sure what is going on. >> The first receiver works well and I loaded the filters fine. However, when I >> went to load the second receiver and run the synthesizer calibration I >> received multiple errors. >> >> E020202 & E027979 - ERR DSE >> E5 ERR VCO >> E000255 ERR VC4 >> ERR PL2 >> >> When I went to install the DSP2 using the utility program I received these >> errors. >> >> DSP 2 verification error >> Error code OXE2046 >> >> >> I reviewed the manual and it says that I have a DSP Echo. The VCO and VC4 >> error may suggest my friend installed the cables incorrectly. Pretty bummed >> right now. Any additional thoughts would be very welcome. > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Parts transfer between rigs
Was the DSP2 board and the synthesizer board for the KRX3 transferred from the other K3. From the errors you are getting, it would seem that they were not. Did your tech elmer just do the unplugging/replugging job or did he check the result out after each option was transferred? What did he say when you asked him for his observations. You may have to contact Elecraft support with your error codes. 73, Don W3FPR On 10/19/2012 3:12 AM, Ham Radio wrote: > I embarked on a project to move parts from one K3 to another and I got the > rigs back from my tech elmer tonight. After getting the K3s home, I decided > to follow the procedure to get them operating again. > > I had my tech elmer transfer the KAT3, KRX3, KDVR3 and KBF3 from one of the > K3 to the other. I now have multiple errors and not sure what is going on. > The first receiver works well and I loaded the filters fine. However, when I > went to load the second receiver and run the synthesizer calibration I > received multiple errors. > > E020202 & E027979 - ERR DSE > E5 ERR VCO > E000255 ERR VC4 > ERR PL2 > > When I went to install the DSP2 using the utility program I received these > errors. > > DSP 2 verification error > Error code OXE2046 > > > I reviewed the manual and it says that I have a DSP Echo. The VCO and VC4 > error may suggest my friend installed the cables incorrectly. Pretty bummed > right now. Any additional thoughts would be very welcome. > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Parts transfer between rigs
Hi Keith, This type of transplant takes more preparation then meets the eye. For example, the Sub RX also includes the addition of a KSYN3 board and an AUX DSP board. Forgetting to install either of those two boards could create some of errors you are seeing. Then there are other things to check and/or change on the existing K3 boards. Similarly, the donor K3 might have to have some things unchanged once this handful of parts has been removed. If the Elmer didn't fire up the rigs after the swap then perhaps he was just supplying skilled labor and he was relying on you to do all of the research. 73, Mike K2MK Keith Heimbold wrote > I embarked on a project to move parts from one K3 to another and I got the > rigs back from my tech elmer tonight. After getting the K3s home, I > decided to follow the procedure to get them operating again. > > I had my tech elmer transfer the KAT3, KRX3, KDVR3 and KBF3 from one of > the K3 to the other. I now have multiple errors and not sure what is > going on. The first receiver works well and I loaded the filters fine. > However, when I went to load the second receiver and run the synthesizer > calibration I received multiple errors. > > E020202 & E027979 - ERR DSE > E5 ERR VCO > E000255 ERR VC4 > ERR PL2 > > When I went to install the DSP2 using the utility program I received these > errors. > > DSP 2 verification error > Error code OXE2046 > > I reviewed the manual and it says that I have a DSP Echo. The VCO and VC4 > error may suggest my friend installed the cables incorrectly. Pretty > bummed right now. Any additional thoughts would be very welcome. > > Thanks, > > Keith > AG6AZ -- View this message in context: http://elecraft.365791.n2.nabble.com/K3-Parts-transfer-between-rigs-tp7564314p7564319.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] K3 Parts transfer between rigs
Keith, You can download the assembly manual for the K3 from http://www.elecraft.com/K2_Manual_Download_Page.htm#K3 and open up the rig and check for errors. It's tedious, but not difficult. Or take it back to uncle Elmer and make him do it. 73, Mike NF4L On 10/19/12 3:12 AM, Ham Radio wrote: > I embarked on a project to move parts from one K3 to another and I got the > rigs back from my tech elmer tonight. After getting the K3s home, I decided > to follow the procedure to get them operating again. > > I had my tech elmer transfer the KAT3, KRX3, KDVR3 and KBF3 from one of the > K3 to the other. I now have multiple errors and not sure what is going on. > The first receiver works well and I loaded the filters fine. However, when I > went to load the second receiver and run the synthesizer calibration I > received multiple errors. > > E020202 & E027979 - ERR DSE > E5 ERR VCO > E000255 ERR VC4 > ERR PL2 > > When I went to install the DSP2 using the utility program I received these > errors. > > DSP 2 verification error > Error code OXE2046 > > > I reviewed the manual and it says that I have a DSP Echo. The VCO and VC4 > error may suggest my friend installed the cables incorrectly. Pretty bummed > right now. Any additional thoughts would be very welcome. > > Thanks, > > Keith > AG6AZ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] K3 Parts transfer between rigs
I embarked on a project to move parts from one K3 to another and I got the rigs back from my tech elmer tonight. After getting the K3s home, I decided to follow the procedure to get them operating again. I had my tech elmer transfer the KAT3, KRX3, KDVR3 and KBF3 from one of the K3 to the other. I now have multiple errors and not sure what is going on. The first receiver works well and I loaded the filters fine. However, when I went to load the second receiver and run the synthesizer calibration I received multiple errors. E020202 & E027979 - ERR DSE E5 ERR VCO E000255 ERR VC4 ERR PL2 When I went to install the DSP2 using the utility program I received these errors. DSP 2 verification error Error code OXE2046 I reviewed the manual and it says that I have a DSP Echo. The VCO and VC4 error may suggest my friend installed the cables incorrectly. Pretty bummed right now. Any additional thoughts would be very welcome. Thanks, Keith AG6AZ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html