[Elecraft] K3 RX Problem
I just purchased a new to me K3-10 S/N 501. I have discovered it has a RX sensitivity problem. After some troubleshooting, I have discovered that the RX is not low on sensitivity (about .25 uV) but has a high noise level when receiving thru the ANT 1 or 2 ports. The background noise with no antenna connected is 10 dB higher on the TX/RX ports than when it is receiving thru the RX only ports. Possibly this is related to the PIN diode antenna switch? Has anyone on the list experienced this? Thanks! Allen, W0OUU __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] K3 - RX Problem after latest firmware update
OK Stewart. I did not think that would really be the problem but I wanted to rule it out anyway. I'm passing this on to Wayne as he is going to have to find what in the firmware that may be causing this to happen. I tried last night and could not reproduct it, but I have seen very few reports of similar situations. Tnx for your patience while this is sorted out. - 73, Greg - AB7R Whidbey Island WA NA-065 K3#0009 and 0319 On Tue Mar 11 9:12 , Stewart Baker sent: >No TCX0-3 fitted. Serial number is 307. > >73 >Stewart G3RXQ >On Mon, 10 Mar 2008 17:16:11 -0400, Greg - AB7R wrote: >> This was true with some early optional TCXO-3 units that had >exposed SMDs on the bottom >> of the can. There was a capacitor that >> >> could potential short to the metal socket where the missing pin >would have been. Hence >> the addition of the insulation. This is >> >> not a problem with the standard reference oscillator as there >are no exposed parts on >> the bottom. >> >> >> Stewart, Do you have the optional TCXO-3 and what is the radio's >serial number? >> >> >> - >> >> 73, >> >> Greg - AB7R >> >> Whidbey Island WA >> >> NA-065 >> >> K3#0009 and 0319 >> >> >> On Mon Mar 10 13:16 , "Bruce Bowman" sent: >> >> >>> Hi Stewart- >>> >>> >>> Like you, I had a problem with my K3 going dead. Unlike you, I >bought a >>> >>> factory-built unit. I did that because I wanted to know it was >working >>> >>> properly from the start. That turned out to be one of those >things that >>> >>> sounds like a good idea but doesn't withstand close scrutiny. >>> >>> >>> What I saw initially was an occasional error message (ERR PL1) >when >>> >>> switching to another band, then the audio would decay to >nothing over a >>> >>> 2 second period. Sometimes I could get it to recover by >chnaging bands, >>> >>> sometimes not. >>> >>> >>> Since it was factory built, they had me return my K3. They >found the >>> >>> TCXO3-1 oscillator was grounding occasionally. The oscillator >would >>> >>> continue to operate, but grounding it (the case? some >component? dunno) >>> >>> caused the frequency to be pulled about 20 KHz and the receiver >would >>> >>> die. They replaced the oscillator (probably unnecessary), added >an >>> >>> insulator and re-ran VCO calibration. It's been rock-solid ever >since. >>> >>> >>> Bruce, NM5B >>> >>> Santa Fe, NM >>> >>> >>> - Original Message - >>> >>> From: "Stewart Baker" [EMAIL PROTECTED]> >>> >>> To: "AB7R" [EMAIL PROTECTED]> "Elecraft Reflector" >>> >>> elecraft@mailman.qth.net> >>> >>> Sent: Monday, March 10, 2008 5:33 AM >>> >>> Subject: RE: [Elecraft] K3 - RX Problem after latest firmware >update >>> >>> >>> Greg, >>> >>> Have re-installed V1.75 & V1.57 again, no change. >>> >>> >>> Here is a sequence which you might like to try:- >>> >>> >>> POWER >>> >>> 80m LSB 3780 >>> >>> NORM >>> >>> LO CUT=0.15 >>> >>> SAV ALT1 >>> >>> NORM >>> >>> TX ON/OFF >>> >>> ALT1 >>> >>> TX ON/OFF >>> >>> Receive may be dead at this point >>> >>> >>> If not continue with >>> >>> Select USB >>> >>> ALT1 >>> >>> TX ON/OFF >>> >>> Receive dead >>> >>> >>> Switching bands, modes or NORM always restores receiver. >>> >>> >>> I do (from my point of view) hope that I am not the only one >with >>> >>> this funny.. >>> >>> >>> 73 >>> >>> Stewart G3RXQ >>> >>> >>> On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: >>> >>>> Stewart, >>>> >>>> >>>> Try installing the new firmware again. I just tried to >recreate >>>> >>> your report >>> >>>> and the radio performs as expected...no problem with RX after >a >>
Re: [Elecraft] K3 - RX Problem after latest firmware update
No TCX0-3 fitted. Serial number is 307. 73 Stewart G3RXQ On Mon, 10 Mar 2008 17:16:11 -0400, Greg - AB7R wrote: > This was true with some early optional TCXO-3 units that had exposed SMDs on the bottom > of the can. There was a capacitor that > > could potential short to the metal socket where the missing pin would have been. Hence > the addition of the insulation. This is > > not a problem with the standard reference oscillator as there are no exposed parts on > the bottom. > > > Stewart, Do you have the optional TCXO-3 and what is the radio's serial number? > > > - > > 73, > > Greg - AB7R > > Whidbey Island WA > > NA-065 > > K3#0009 and 0319 > > > On Mon Mar 10 13:16 , "Bruce Bowman" sent: > > >> Hi Stewart- >> >> >> Like you, I had a problem with my K3 going dead. Unlike you, I bought a >> >> factory-built unit. I did that because I wanted to know it was working >> >> properly from the start. That turned out to be one of those things that >> >> sounds like a good idea but doesn't withstand close scrutiny. >> >> >> What I saw initially was an occasional error message (ERR PL1) when >> >> switching to another band, then the audio would decay to nothing over a >> >> 2 second period. Sometimes I could get it to recover by chnaging bands, >> >> sometimes not. >> >> >> Since it was factory built, they had me return my K3. They found the >> >> TCXO3-1 oscillator was grounding occasionally. The oscillator would >> >> continue to operate, but grounding it (the case? some component? dunno) >> >> caused the frequency to be pulled about 20 KHz and the receiver would >> >> die. They replaced the oscillator (probably unnecessary), added an >> >> insulator and re-ran VCO calibration. It's been rock-solid ever since. >> >> >> Bruce, NM5B >> >> Santa Fe, NM >> >> >> - Original Message - >> >> From: "Stewart Baker" [EMAIL PROTECTED]> >> >> To: "AB7R" [EMAIL PROTECTED]> "Elecraft Reflector" >> >> elecraft@mailman.qth.net> >> >> Sent: Monday, March 10, 2008 5:33 AM >> >> Subject: RE: [Elecraft] K3 - RX Problem after latest firmware update >> >> >> Greg, >> >> Have re-installed V1.75 & V1.57 again, no change. >> >> >> Here is a sequence which you might like to try:- >> >> >> POWER >> >> 80m LSB 3780 >> >> NORM >> >> LO CUT=0.15 >> >> SAV ALT1 >> >> NORM >> >> TX ON/OFF >> >> ALT1 >> >> TX ON/OFF >> >> Receive may be dead at this point >> >> >> If not continue with >> >> Select USB >> >> ALT1 >> >> TX ON/OFF >> >> Receive dead >> >> >> Switching bands, modes or NORM always restores receiver. >> >> >> I do (from my point of view) hope that I am not the only one with >> >> this funny.. >> >> >> 73 >> >> Stewart G3RXQ >> >> >> On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: >> >>> Stewart, >>> >>> >>> Try installing the new firmware again. I just tried to recreate >>> >> your report >> >>> and the radio performs as expected...no problem with RX after a >>> >> transmit >> >>> with ALT1 set to 0.15 on the LO side. >>> >>> >>> 73 >>> >>> Greg >>> >>> AB7R >>> >>> >>> -Original Message- >>> >>> From: [EMAIL PROTECTED] >>> >>> [EMAIL PROTECTED]','','','')">[EMAIL PROTECTED] lman.qth.net]On >>> Behalf Of Stewart >>> >> Baker >> >>> Sent: Sunday, March 09, 2008 11:32 AM >>> >>> To: Elecraft Reflector >>> >>> Subject: [Elecraft] K3 - RX Problem after latest firmware update >>> >>> >>> I am not sure if there is an obscure problem after the latest >>> >> MCU >> >>> and DSP update. Maybe others could check and see if it happens >>> >> to >> >>> them ? >>> >>> >>> Any band on SSB if I have the DSP set to ALT1 with the Low Cut >>> >> set >> >>> at 0.15 Hz , then after going onto transmit the receiver appears >&g
Re: [Elecraft] K3 - RX Problem after latest firmware update
Hi Doug- Quite a ways behind you at #136. I don't know if they've worked the insulator into production or if it's a do-it-if-it-needs-it kind of fix. Bruce, NM5B > Hi, > Which serial #? I have #22 and had the same problem. I took it to > Aptos and it seems to be fixed. > > 73, doug > > From: "Bruce Bowman" <[EMAIL PROTECTED]> > Date: Mon, 10 Mar 2008 14:16:26 -0600 > > Hi Stewart- > > Like you, I had a problem with my K3 going dead. Unlike you, I > bought a > factory-built unit. I did that because I wanted to know it was > working > properly from the start. That turned out to be one of those things > that > sounds like a good idea but doesn't withstand close scrutiny. > > What I saw initially was an occasional error message (ERR PL1) when > switching to another band, then the audio would decay to nothing > over a > 2 second period. Sometimes I could get it to recover by chnaging > bands, > sometimes not. > > Since it was factory built, they had me return my K3. They found the > TCXO3-1 oscillator was grounding occasionally. The oscillator would > continue to operate, but grounding it (the case? some component? > dunno) > caused the frequency to be pulled about 20 KHz and the receiver > would > die. They replaced the oscillator (probably unnecessary), added an > insulator and re-ran VCO calibration. It's been rock-solid ever > since. > > Bruce, NM5B > Santa Fe, NM > > - Original Message - > From: "Stewart Baker" <[EMAIL PROTECTED]> > To: "AB7R" <[EMAIL PROTECTED]>; "Elecraft Reflector" > > Sent: Monday, March 10, 2008 5:33 AM > Subject: RE: [Elecraft] K3 - RX Problem after latest firmware update > > > Greg, > Have re-installed V1.75 & V1.57 again, no change. > > Here is a sequence which you might like to try:- > > POWER > 80m LSB 3780 > NORM > LO CUT=0.15 > SAV ALT1 > NORM > TX ON/OFF > ALT1 > TX ON/OFF > Receive may be dead at this point > > If not continue with > Select USB > ALT1 > TX ON/OFF > Receive dead > > Switching bands, modes or NORM always restores receiver. > > I do (from my point of view) hope that I am not the only one with > this funny.. > > 73 > Stewart G3RXQ > > On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: > > Stewart, > > > > Try installing the new firmware again. I just tried to recreate > your report > > and the radio performs as expected...no problem with RX after a > transmit > > with ALT1 set to 0.15 on the LO side. > > > > 73 > > Greg > > AB7R > > > > > > -Original Message- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] Behalf Of Stewart > Baker > > Sent: Sunday, March 09, 2008 11:32 AM > > To: Elecraft Reflector > > Subject: [Elecraft] K3 - RX Problem after latest firmware update > > > > > > I am not sure if there is an obscure problem after the latest > MCU > > and DSP update. Maybe others could check and see if it happens > to > > them ? > > > > Any band on SSB if I have the DSP set to ALT1 with the Low Cut > set > > at 0.15 Hz , then after going onto transmit the receiver appears > > to be dead. If I set the DSP to NORM by pressing the knob the > > receiver suddenly bursts into life... > > This happens whether there is any transmit audio or RF out. > > > > 73 > > Stewart G3RXQ > > ___ > > Elecraft mailing list > > Post to: Elecraft@mailman.qth.net > > You must be a subscriber to post to the list. > > Subscriber Info (Addr. Change, sub, unsub etc.): > > http://mailman.qth.net/mailman/listinfo/elecraft > > > > Help: http://mailman.qth.net/subscribers.htm > > Elecraft web page: http://www.elecraft.com > > No virus found in this incoming message. > > Checked by AVG. > > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: > 3/9/2008 > > 12:17 PM > > > > No virus found in this outgoing message. > > Checked by AVG. > > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: > 3/9/2008 > > 12:17 PM > > > ___ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): &g
Re: [Elecraft] K3 - RX Problem after latest firmware update
This was true with some early optional TCXO-3 units that had exposed SMDs on the bottom of the can. There was a capacitor that could potential short to the metal socket where the missing pin would have been. Hence the addition of the insulation. This is not a problem with the standard reference oscillator as there are no exposed parts on the bottom. Stewart, Do you have the optional TCXO-3 and what is the radio's serial number? - 73, Greg - AB7R Whidbey Island WA NA-065 K3#0009 and 0319 On Mon Mar 10 13:16 , "Bruce Bowman" sent: >Hi Stewart- > >Like you, I had a problem with my K3 going dead. Unlike you, I bought a >factory-built unit. I did that because I wanted to know it was working >properly from the start. That turned out to be one of those things that >sounds like a good idea but doesn't withstand close scrutiny. > >What I saw initially was an occasional error message (ERR PL1) when >switching to another band, then the audio would decay to nothing over a >2 second period. Sometimes I could get it to recover by chnaging bands, >sometimes not. > >Since it was factory built, they had me return my K3. They found the >TCXO3-1 oscillator was grounding occasionally. The oscillator would >continue to operate, but grounding it (the case? some component? dunno) >caused the frequency to be pulled about 20 KHz and the receiver would >die. They replaced the oscillator (probably unnecessary), added an >insulator and re-ran VCO calibration. It's been rock-solid ever since. > >Bruce, NM5B >Santa Fe, NM > >- Original Message - >From: "Stewart Baker" [EMAIL PROTECTED]> >To: "AB7R" [EMAIL PROTECTED]>; "Elecraft Reflector" >elecraft@mailman.qth.net> >Sent: Monday, March 10, 2008 5:33 AM >Subject: RE: [Elecraft] K3 - RX Problem after latest firmware update > > >Greg, >Have re-installed V1.75 & V1.57 again, no change. > >Here is a sequence which you might like to try:- > >POWER >80m LSB 3780 >NORM >LO CUT=0.15 >SAV ALT1 >NORM >TX ON/OFF >ALT1 >TX ON/OFF >Receive may be dead at this point > >If not continue with >Select USB >ALT1 >TX ON/OFF >Receive dead > >Switching bands, modes or NORM always restores receiver. > >I do (from my point of view) hope that I am not the only one with >this funny.. > >73 >Stewart G3RXQ > >On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: >> Stewart, >> >> Try installing the new firmware again. I just tried to recreate >your report >> and the radio performs as expected...no problem with RX after a >transmit >> with ALT1 set to 0.15 on the LO side. >> >> 73 >> Greg >> AB7R >> >> >> -Original Message- >> From: [EMAIL PROTECTED] >> [EMAIL PROTECTED]','','','')">[EMAIL PROTECTED] Behalf Of Stewart >Baker >> Sent: Sunday, March 09, 2008 11:32 AM >> To: Elecraft Reflector >> Subject: [Elecraft] K3 - RX Problem after latest firmware update >> >> >> I am not sure if there is an obscure problem after the latest >MCU >> and DSP update. Maybe others could check and see if it happens >to >> them ? >> >> Any band on SSB if I have the DSP set to ALT1 with the Low Cut >set >> at 0.15 Hz , then after going onto transmit the receiver appears >> to be dead. If I set the DSP to NORM by pressing the knob the >> receiver suddenly bursts into life... >> This happens whether there is any transmit audio or RF out. >> >> 73 >> Stewart G3RXQ >> ___ >> Elecraft mailing list >> Post to: Elecraft@mailman.qth.net >> You must be a subscriber to post to the list. >> Subscriber Info (Addr. Change, sub, unsub etc.): >> http://mailman.qth.net/mailman/listinfo/elecraft >> >> Help: http://mailman.qth.net/subscribers.htm >> Elecraft web page: http://www.elecraft.com >> No virus found in this incoming message. >> Checked by AVG. >> Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: >3/9/2008 >> 12:17 PM >> >> No virus found in this outgoing message. >> Checked by AVG. >> Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: >3/9/2008 >> 12:17 PM > > >___ >Elecraft mailing list >Post to: Elecraft@mailman.qth.net >You must be a subscriber to post to the list. >Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > >Help: http://mailman.qth.net/subscribers.htm >Elecraft web pa
Re: [Elecraft] K3 - RX Problem after latest firmware update
Hi Stewart- Like you, I had a problem with my K3 going dead. Unlike you, I bought a factory-built unit. I did that because I wanted to know it was working properly from the start. That turned out to be one of those things that sounds like a good idea but doesn't withstand close scrutiny. What I saw initially was an occasional error message (ERR PL1) when switching to another band, then the audio would decay to nothing over a 2 second period. Sometimes I could get it to recover by chnaging bands, sometimes not. Since it was factory built, they had me return my K3. They found the TCXO3-1 oscillator was grounding occasionally. The oscillator would continue to operate, but grounding it (the case? some component? dunno) caused the frequency to be pulled about 20 KHz and the receiver would die. They replaced the oscillator (probably unnecessary), added an insulator and re-ran VCO calibration. It's been rock-solid ever since. Bruce, NM5B Santa Fe, NM - Original Message - From: "Stewart Baker" <[EMAIL PROTECTED]> To: "AB7R" <[EMAIL PROTECTED]>; "Elecraft Reflector" Sent: Monday, March 10, 2008 5:33 AM Subject: RE: [Elecraft] K3 - RX Problem after latest firmware update Greg, Have re-installed V1.75 & V1.57 again, no change. Here is a sequence which you might like to try:- POWER 80m LSB 3780 NORM LO CUT=0.15 SAV ALT1 NORM TX ON/OFF ALT1 TX ON/OFF Receive may be dead at this point If not continue with Select USB ALT1 TX ON/OFF Receive dead Switching bands, modes or NORM always restores receiver. I do (from my point of view) hope that I am not the only one with this funny.. 73 Stewart G3RXQ On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: > Stewart, > > Try installing the new firmware again. I just tried to recreate your report > and the radio performs as expected...no problem with RX after a transmit > with ALT1 set to 0.15 on the LO side. > > 73 > Greg > AB7R > > > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Stewart Baker > Sent: Sunday, March 09, 2008 11:32 AM > To: Elecraft Reflector > Subject: [Elecraft] K3 - RX Problem after latest firmware update > > > I am not sure if there is an obscure problem after the latest MCU > and DSP update. Maybe others could check and see if it happens to > them ? > > Any band on SSB if I have the DSP set to ALT1 with the Low Cut set > at 0.15 Hz , then after going onto transmit the receiver appears > to be dead. If I set the DSP to NORM by pressing the knob the > receiver suddenly bursts into life... > This happens whether there is any transmit audio or RF out. > > 73 > Stewart G3RXQ > ___ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > No virus found in this incoming message. > Checked by AVG. > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 > 12:17 PM > > No virus found in this outgoing message. > Checked by AVG. > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 > 12:17 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Fwd: Re: [Elecraft] K3 - RX Problem after latest firmware update]
Original Message Subject:Re: [Elecraft] K3 - RX Problem after latest firmware update Date: Mon, 10 Mar 2008 08:58:47 -0400 From: Ken K3IU <[EMAIL PROTECTED]> To: Stewart Baker <[EMAIL PROTECTED]> CC: AB7R <[EMAIL PROTECTED]>, Elecraft Reflector References: <[EMAIL PROTECTED]> Hi Stewart: I just ran #202 with the latest firmware through your steps several times and I cannot duplicate your problem. The receiver never goes dead at any time. 73, Ken K3IU Stewart Baker wrote: Greg, Have re-installed V1.75 & V1.57 again, no change. Here is a sequence which you might like to try:- POWER 80m LSB 3780 NORM LO CUT=0.15 SAV ALT1 NORM TX ON/OFF ALT1 TX ON/OFF Receive may be dead at this point If not continue with Select USB ALT1 TX ON/OFF Receive dead Switching bands, modes or NORM always restores receiver. I do (from my point of view) hope that I am not the only one with this funny.. 73 Stewart G3RXQ On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: Stewart, Try installing the new firmware again. I just tried to recreate your report and the radio performs as expected...no problem with RX after a transmit with ALT1 set to 0.15 on the LO side. 73 Greg AB7R -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Stewart Baker Sent: Sunday, March 09, 2008 11:32 AM To: Elecraft Reflector Subject: [Elecraft] K3 - RX Problem after latest firmware update I am not sure if there is an obscure problem after the latest MCU and DSP update. Maybe others could check and see if it happens to them ? Any band on SSB if I have the DSP set to ALT1 with the Low Cut set at 0.15 Hz , then after going onto transmit the receiver appears to be dead. If I set the DSP to NORM by pressing the knob the receiver suddenly bursts into life... This happens whether there is any transmit audio or RF out. 73 Stewart G3RXQ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG. Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 12:17 PM No virus found in this outgoing message. Checked by AVG. Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 12:17 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] K3 - RX Problem after latest firmware update
Greg, Have re-installed V1.75 & V1.57 again, no change. Here is a sequence which you might like to try:- POWER 80m LSB 3780 NORM LO CUT=0.15 SAV ALT1 NORM TX ON/OFF ALT1 TX ON/OFF Receive may be dead at this point If not continue with Select USB ALT1 TX ON/OFF Receive dead Switching bands, modes or NORM always restores receiver. I do (from my point of view) hope that I am not the only one with this funny.. 73 Stewart G3RXQ On Sun, 9 Mar 2008 12:30:15 -0700, AB7R wrote: > Stewart, > > Try installing the new firmware again. I just tried to recreate your report > and the radio performs as expected...no problem with RX after a transmit > with ALT1 set to 0.15 on the LO side. > > 73 > Greg > AB7R > > > -Original Message- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Stewart Baker > Sent: Sunday, March 09, 2008 11:32 AM > To: Elecraft Reflector > Subject: [Elecraft] K3 - RX Problem after latest firmware update > > > I am not sure if there is an obscure problem after the latest MCU > and DSP update. Maybe others could check and see if it happens to > them ? > > Any band on SSB if I have the DSP set to ALT1 with the Low Cut set > at 0.15 Hz , then after going onto transmit the receiver appears > to be dead. If I set the DSP to NORM by pressing the knob the > receiver suddenly bursts into life... > This happens whether there is any transmit audio or RF out. > > 73 > Stewart G3RXQ > ___ > Elecraft mailing list > Post to: Elecraft@mailman.qth.net > You must be a subscriber to post to the list. > Subscriber Info (Addr. Change, sub, unsub etc.): > http://mailman.qth.net/mailman/listinfo/elecraft > > Help: http://mailman.qth.net/subscribers.htm > Elecraft web page: http://www.elecraft.com > No virus found in this incoming message. > Checked by AVG. > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 > 12:17 PM > > No virus found in this outgoing message. > Checked by AVG. > Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 > 12:17 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] K3 - RX Problem after latest firmware update
Stewart, Try installing the new firmware again. I just tried to recreate your report and the radio performs as expected...no problem with RX after a transmit with ALT1 set to 0.15 on the LO side. 73 Greg AB7R -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Stewart Baker Sent: Sunday, March 09, 2008 11:32 AM To: Elecraft Reflector Subject: [Elecraft] K3 - RX Problem after latest firmware update I am not sure if there is an obscure problem after the latest MCU and DSP update. Maybe others could check and see if it happens to them ? Any band on SSB if I have the DSP set to ALT1 with the Low Cut set at 0.15 Hz , then after going onto transmit the receiver appears to be dead. If I set the DSP to NORM by pressing the knob the receiver suddenly bursts into life... This happens whether there is any transmit audio or RF out. 73 Stewart G3RXQ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG. Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 12:17 PM No virus found in this outgoing message. Checked by AVG. Version: 7.5.518 / Virus Database: 269.21.7/1322 - Release Date: 3/9/2008 12:17 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] K3 - RX Problem after latest firmware update
I am not sure if there is an obscure problem after the latest MCU and DSP update. Maybe others could check and see if it happens to them ? Any band on SSB if I have the DSP set to ALT1 with the Low Cut set at 0.15 Hz , then after going onto transmit the receiver appears to be dead. If I set the DSP to NORM by pressing the knob the receiver suddenly bursts into life... This happens whether there is any transmit audio or RF out. 73 Stewart G3RXQ ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com