RE: [Elecraft] Split ops?
Bob Serwy wrote: Yes there is. I use it. 'k31;swt13;swt13;k30; OK. I mis-remembered the problem I had trying to get this to work. I'm sending SWT13;SWT13;UPB4;UPB4;SWH13; The two VFOs *are* being set to the same frequency and mode, and SPLIT is being engaged, but VFO B is not being set 2KHz higher in frequency. - Julian, G4ILO K3 s/n: 222 K2 s/n: 392 G4ILO's Shack: www.g4ilo.com KComm for K2/K3: www.g4ilo.com/kcomm.html -- View this message in context: http://www.nabble.com/Split-ops--tp18282086p18290111.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Split ops?
From what I can tell, the UPBn; has not been implemented. All you can do is use up; (for 10 Hz on the VFO A) So you must use 200 up;'s (not practical). Then do a swt11; (to swap VFO's). Also use ft1; to turn on split. (That is a number one.) All swh13; does is toggle split on and off. Bob Serwy - N9RS -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of G4ILO Sent: Saturday, July 05, 2008 3:45 AM To: elecraft@mailman.qth.net Subject: RE: [Elecraft] Split ops? Bob Serwy wrote: Yes there is. I use it. 'k31;swt13;swt13;k30; OK. I mis-remembered the problem I had trying to get this to work. I'm sending SWT13;SWT13;UPB4;UPB4;SWH13; The two VFOs *are* being set to the same frequency and mode, and SPLIT is being engaged, but VFO B is not being set 2KHz higher in frequency. - Julian, G4ILO K3 s/n: 222 K2 s/n: 392 G4ILO's Shack: www.g4ilo.com KComm for K2/K3: www.g4ilo.com/kcomm.html -- View this message in context: http://www.nabble.com/Split-ops--tp18282086p18290111.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Split ops?
I was able to get the up4 (not the upb4) to work by keeping this command in a separate macro from the sw commands. Bob Serwy - N9RS -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of G4ILO Sent: Saturday, July 05, 2008 3:45 AM To: elecraft@mailman.qth.net Subject: RE: [Elecraft] Split ops? Bob Serwy wrote: Yes there is. I use it. 'k31;swt13;swt13;k30; OK. I mis-remembered the problem I had trying to get this to work. I'm sending SWT13;SWT13;UPB4;UPB4;SWH13; The two VFOs *are* being set to the same frequency and mode, and SPLIT is being engaged, but VFO B is not being set 2KHz higher in frequency. - Julian, G4ILO K3 s/n: 222 K2 s/n: 392 G4ILO's Shack: www.g4ilo.com KComm for K2/K3: www.g4ilo.com/kcomm.html -- View this message in context: http://www.nabble.com/Split-ops--tp18282086p18290111.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
[Elecraft] Split ops?
When making the selection AB then holding Split I notice that the mode stays where it last was...i.e., 14005 on A and 14180 on B; after AB the B vfo is 14005 but remains in USB. I have looked thru the menu selections and can not find anything to have the modes match after doing AB...have I missed something? If not, why not match freq and mode? 73 Tom CX7TT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Split ops?
Hi Tom, You need to tap A=B twice to transfer all the parameters, freq, mode, etc. 73, Bud N7CW -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of TMorton Sent: Friday, July 04, 2008 8:56 AM To: elecraft@mailman.qth.net Subject: [Elecraft] Split ops? When making the selection AB then holding Split I notice that the mode stays where it last was...i.e., 14005 on A and 14180 on B; after AB the B vfo is 14005 but remains in USB. I have looked thru the menu selections and can not find anything to have the modes match after doing AB...have I missed something? If not, why not match freq and mode? 73 Tom CX7TT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Split ops?
A second button press is now required to transfer the mode setting. According to the release notes for version MCU 1.87 / DSP 1.69: * A-B SWITCH: 1st tap copies frequency only; 2nd tap within 2 seconds copies mode and filter settings. Bob NW8L On Fri, Jul 4, 2008 at 9:56 AM, TMorton [EMAIL PROTECTED] wrote: When making the selection AB then holding Split I notice that the mode stays where it last was...i.e., 14005 on A and 14180 on B; after AB the B vfo is 14005 but remains in USB. I have looked thru the menu selections and can not find anything to have the modes match after doing AB...have I missed something? If not, why not match freq and mode? 73 Tom CX7TT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Split ops?
Tom, Several folks wanted it that way (for several reasons), so there was a recent change. One tap of the AB button changes only the frequency. Two taps will change the mode and other settings too. Look at the firmware release notes for further explanation. 73, Don W3FPR TMorton wrote: When making the selection AB then holding Split I notice that the mode stays where it last was...i.e., 14005 on A and 14180 on B; after AB the B vfo is 14005 but remains in USB. I have looked thru the menu selections and can not find anything to have the modes match after doing AB...have I missed something? If not, why not match freq and mode? 73 Tom CX7TT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Split ops?
Tap AB a second time right after the first tap. Then you will see AB ALL. 73 Greg AB7R - Original Message - From: TMorton [EMAIL PROTECTED] To: elecraft@mailman.qth.net Sent: Friday, July 04, 2008 8:56 AM Subject: [Elecraft] Split ops? When making the selection AB then holding Split I notice that the mode stays where it last was...i.e., 14005 on A and 14180 on B; after AB the B vfo is 14005 but remains in USB. I have looked thru the menu selections and can not find anything to have the modes match after doing AB...have I missed something? If not, why not match freq and mode? 73 Tom CX7TT ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com No virus found in this incoming message. Checked by AVG - http://www.avg.com Version: 8.0.138 / Virus Database: 270.4.5/1533 - Release Date: 7/3/2008 7:19 PM ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
Re: [Elecraft] Split ops?
Don Wilhelm wrote: Several folks wanted it that way (for several reasons), so there was a recent change. One tap of the AB button changes only the frequency. Two taps will change the mode and other settings too. Look at the firmware release notes for further explanation. Unfortunately, sending two software commands that simulate pressing AB in succession doesn't have the same effect. So there is no way to set VFO B to the same mode as A using a macro. - Julian, G4ILO K3 s/n: 222 K2 s/n: 392 G4ILO's Shack: www.g4ilo.com KComm for K2/K3: www.g4ilo.com/kcomm.html -- View this message in context: http://www.nabble.com/Split-ops--tp18282086p18286654.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com
RE: [Elecraft] Split ops?
Yes there is. I use it. 'k31;swt13;swt13;k30; Bob Serwy - N9RS -Original Message- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of G4ILO Sent: Friday, July 04, 2008 4:57 PM To: elecraft@mailman.qth.net Subject: Re: [Elecraft] Split ops? Don Wilhelm wrote: Several folks wanted it that way (for several reasons), so there was a recent change. One tap of the AB button changes only the frequency. Two taps will change the mode and other settings too. Look at the firmware release notes for further explanation. Unfortunately, sending two software commands that simulate pressing AB in succession doesn't have the same effect. So there is no way to set VFO B to the same mode as A using a macro. - Julian, G4ILO K3 s/n: 222 K2 s/n: 392 G4ILO's Shack: www.g4ilo.com KComm for K2/K3: www.g4ilo.com/kcomm.html -- View this message in context: http://www.nabble.com/Split-ops--tp18282086p18286654.html Sent from the Elecraft mailing list archive at Nabble.com. ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com ___ Elecraft mailing list Post to: Elecraft@mailman.qth.net You must be a subscriber to post to the list. Subscriber Info (Addr. Change, sub, unsub etc.): http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/subscribers.htm Elecraft web page: http://www.elecraft.com