Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
All, To amplify Bob's comments --- That is one of the situations with digital displays Vs. analog. An analog display might show your an SWR of 1.55 (if you can interpolate the needle position) while the digital display resolution will show you either a 1.5 or a 1.6 indication - there is no way to show an in-between reading on a digital display. 73, Don W3FPR On 4/6/2019 5:04 PM, Bob McGraw K4TAX wrote: The SWR LED scaling on the KPA500 is different than the scaling on the KAT500. Yet the KPA500 does have a numerical readout..if one wishes to split hairs. 1.0, 1.1, 1.2, 1.3 and etc. With LED type displays, there is always a "transition" point from one value / LED to the next. It could be at 1.4, or 1.5 or 1.6. Thus a value of 1.4 on one device could be 1.6 on another. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
Dick, thank you for jumping in. Has been a long time since I used the KAT500 now that KPA1500 is in the shack! 72 & 73, Bill K9YEQ FT'er for K2, KX1, KX3, KXPA100, KAT500, W2, etc. -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of d...@elecraft.com Sent: Saturday, April 6, 2019 4:36 PM To: 'wmbrian' ; elecraft@mailman.qth.net Subject: Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR Brian: Your KAT500 low order SWR LED, labeled "1.2", is illuminated when there is a little bit of forward power and an SWR of 1.2:1 or higher is computed. If the SWR is under 1.2:1, then no KAT500 SWR LEDs are illuminated. Even 500 watts of RF with little or no reflected power shouldn't light any KAT500 SWR LEDs. The KPA500 (and KPA1500) have an SWR bar LED for 1.0. The KAT500's first SWR LED is 1.2. Fred's book is correct; your KAT500 performs an SWR calculation whether or not the ATU is bypassed. That result can be displayed with the KAT500 Utility Operate page, or any other program that can send a command to the KAT500 to read its SWR. If SWR is 1.2:1 or higher, then it's also displayed on KAT500 SWR LEDs. 73 de Dick, K6KR -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of wmbrian Sent: Saturday, April 6, 2019 11:02 To: elecraft@mailman.qth.net Subject: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR I recently added the KAT500 and KPA500 to my K3 station. I have noticed that when the SWR (after tuning) as displayed on the KPA500 is 1.0/1 (or occasionally 1.1/1) no SWR LED lights up on the KAT500. (The green 1.0/1 SWR LED on the KPA500 does light up.) I have assumed that the 1.2/1 KAT500 SWR LED does not light up is because 1) the KAT500 threshold for the first SWR LED is 1.2/1 and 2) because no tuning action has taken place in these circumstances (due to memorized KAT500 tuning configuration). However, I noticed at the bottom of page 49 of Fred Cady's book on the KAT500 and the KPA500 it says "VSWR is displayed even when the tuner is bypasssed". So, I'm confused. Does no SWR LED light when the SWR is 1.0/1 (or very close to it) because the SWR is below 1.2/1? Thanks, Brian, K8GRR -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
Brian: Your KAT500 low order SWR LED, labeled "1.2", is illuminated when there is a little bit of forward power and an SWR of 1.2:1 or higher is computed. If the SWR is under 1.2:1, then no KAT500 SWR LEDs are illuminated. Even 500 watts of RF with little or no reflected power shouldn't light any KAT500 SWR LEDs. The KPA500 (and KPA1500) have an SWR bar LED for 1.0. The KAT500's first SWR LED is 1.2. Fred's book is correct; your KAT500 performs an SWR calculation whether or not the ATU is bypassed. That result can be displayed with the KAT500 Utility Operate page, or any other program that can send a command to the KAT500 to read its SWR. If SWR is 1.2:1 or higher, then it's also displayed on KAT500 SWR LEDs. 73 de Dick, K6KR -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of wmbrian Sent: Saturday, April 6, 2019 11:02 To: elecraft@mailman.qth.net Subject: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR I recently added the KAT500 and KPA500 to my K3 station. I have noticed that when the SWR (after tuning) as displayed on the KPA500 is 1.0/1 (or occasionally 1.1/1) no SWR LED lights up on the KAT500. (The green 1.0/1 SWR LED on the KPA500 does light up.) I have assumed that the 1.2/1 KAT500 SWR LED does not light up is because 1) the KAT500 threshold for the first SWR LED is 1.2/1 and 2) because no tuning action has taken place in these circumstances (due to memorized KAT500 tuning configuration). However, I noticed at the bottom of page 49 of Fred Cady's book on the KAT500 and the KPA500 it says "VSWR is displayed even when the tuner is bypasssed". So, I'm confused. Does no SWR LED light when the SWR is 1.0/1 (or very close to it) because the SWR is below 1.2/1? Thanks, Brian, K8GRR -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
Bob, thanks for input, but I understand the issue as to not get a reading on the SWR display of the KTA500 and the concern is there may be something amiss. Thus my suggestion to be sure the SWR LED is working and to figure it out, I suggested a simple method to make sure the LED on the SWR indicator can register/is working. 73, Bill K9YEQ https://wrj-tech.com/ -Original Message- From: Bob McGraw K4TAX Sent: Saturday, April 6, 2019 4:04 PM To: Bill Johnson Cc: wmbrian ; elecraft@mailman.qth.net Subject: Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR The SWR LED scaling on the KPA500 is different than the scaling on the KAT500. Yet the KPA500 does have a numerical readout..if one wishes to split hairs. 1.0, 1.1, 1.2, 1.3 and etc. With LED type displays, there is always a "transition" point from one value / LED to the next. It could be at 1.4, or 1.5 or 1.6. Thus a value of 1.4 on one device could be 1.6 on another. Bob, K4TAX Sent from my iPhone > On Apr 6, 2019, at 3:13 PM, Bill Johnson wrote: > > Does the power output LEDs give a reading? If they do and you show no > reflected that should be ok. If you have a bride after that it may show no > lite either. You can always bypass the KPA's and find a frequency where you > see 2:1 then turn the KPA's back on and see if that gives a reading. If not, > suggest you call tech support. > > 72 & 73, > Bill > K9YEQ > FT'er for K2, KX1, KX3, KXPA100, KAT500, W2, etc. > > -Original Message- > From: elecraft-boun...@mailman.qth.net > On Behalf Of wmbrian > Sent: Saturday, April 6, 2019 1:02 PM > To: elecraft@mailman.qth.net > Subject: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR > > I recently added the KAT500 and KPA500 to my K3 station. > > I have noticed that when the SWR (after tuning) as displayed on the > KPA500 is 1.0/1 (or occasionally 1.1/1) no SWR LED lights up on the > KAT500. (The green 1.0/1 SWR LED on the KPA500 does light up.) > > I have assumed that the 1.2/1 KAT500 SWR LED does not light up is > because 1) the KAT500 threshold for the first SWR LED is 1.2/1 and 2) > because no tuning action has taken place in these circumstances (due > to memorized > KAT500 tuning configuration). However, I noticed at the bottom of page 49 of > Fred Cady's book on the KAT500 and the KPA500 it says "VSWR is displayed even > when the tuner is bypasssed". So, I'm confused. Does no SWR LED light when > the SWR is 1.0/1 (or very close to it) because the SWR is below 1.2/1? > > Thanks, > > Brian, K8GRR > > > > -- > Sent from: http://elecraft.365791.n2.nabble.com/ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net Please help support this email > list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
The SWR LED scaling on the KPA500 is different than the scaling on the KAT500. Yet the KPA500 does have a numerical readout..if one wishes to split hairs. 1.0, 1.1, 1.2, 1.3 and etc. With LED type displays, there is always a "transition" point from one value / LED to the next. It could be at 1.4, or 1.5 or 1.6. Thus a value of 1.4 on one device could be 1.6 on another. Bob, K4TAX Sent from my iPhone > On Apr 6, 2019, at 3:13 PM, Bill Johnson wrote: > > Does the power output LEDs give a reading? If they do and you show no > reflected that should be ok. If you have a bride after that it may show no > lite either. You can always bypass the KPA's and find a frequency where you > see 2:1 then turn the KPA's back on and see if that gives a reading. If not, > suggest you call tech support. > > 72 & 73, > Bill > K9YEQ > FT'er for K2, KX1, KX3, KXPA100, KAT500, W2, etc. > > -Original Message- > From: elecraft-boun...@mailman.qth.net On > Behalf Of wmbrian > Sent: Saturday, April 6, 2019 1:02 PM > To: elecraft@mailman.qth.net > Subject: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR > > I recently added the KAT500 and KPA500 to my K3 station. > > I have noticed that when the SWR (after tuning) as displayed on the KPA500 > is 1.0/1 (or occasionally 1.1/1) no SWR LED lights up on the KAT500. (The > green 1.0/1 SWR LED on the KPA500 does light up.) > > I have assumed that the 1.2/1 KAT500 SWR LED does not light up is because 1) > the KAT500 threshold for the first SWR LED is 1.2/1 and 2) because no tuning > action has taken place in these circumstances (due to memorized > KAT500 tuning configuration). However, I noticed at the bottom of page 49 of > Fred Cady's book on the KAT500 and the KPA500 it says "VSWR is displayed even > when the tuner is bypasssed". So, I'm confused. Does no SWR LED light when > the SWR is 1.0/1 (or very close to it) because the SWR is below 1.2/1? > > Thanks, > > Brian, K8GRR > > > > -- > Sent from: http://elecraft.365791.n2.nabble.com/ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
Does the power output LEDs give a reading? If they do and you show no reflected that should be ok. If you have a bride after that it may show no lite either. You can always bypass the KPA's and find a frequency where you see 2:1 then turn the KPA's back on and see if that gives a reading. If not, suggest you call tech support. 72 & 73, Bill K9YEQ FT'er for K2, KX1, KX3, KXPA100, KAT500, W2, etc. -Original Message- From: elecraft-boun...@mailman.qth.net On Behalf Of wmbrian Sent: Saturday, April 6, 2019 1:02 PM To: elecraft@mailman.qth.net Subject: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR I recently added the KAT500 and KPA500 to my K3 station. I have noticed that when the SWR (after tuning) as displayed on the KPA500 is 1.0/1 (or occasionally 1.1/1) no SWR LED lights up on the KAT500. (The green 1.0/1 SWR LED on the KPA500 does light up.) I have assumed that the 1.2/1 KAT500 SWR LED does not light up is because 1) the KAT500 threshold for the first SWR LED is 1.2/1 and 2) because no tuning action has taken place in these circumstances (due to memorized KAT500 tuning configuration). However, I noticed at the bottom of page 49 of Fred Cady's book on the KAT500 and the KPA500 it says "VSWR is displayed even when the tuner is bypasssed". So, I'm confused. Does no SWR LED light when the SWR is 1.0/1 (or very close to it) because the SWR is below 1.2/1? Thanks, Brian, K8GRR -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] KAT500 SWR LED Doesn't Light with 1.0/1 SWR
Yes I have that combination, KPA500 / KAT500. Over the years I've learned that a VSWR of 1.5:1 or less means little to nothing. Oh it's "comforting" to operate all the time with a 1.1:1 SWR but just accurate is that indication? And the fact the two devices show different values lends credence to " just how accurate is that indication". Plus many diode detection methods are least accurate at lower levels. Conclusion: find something more interesting to worry about. Bob, K4TAX Sent from my iPhone > On Apr 6, 2019, at 1:01 PM, wmbrian wrote: > > I recently added the KAT500 and KPA500 to my K3 station. > > I have noticed that when the SWR (after tuning) as displayed on the KPA500 > is 1.0/1 (or occasionally 1.1/1) no SWR LED lights up on the KAT500. (The > green 1.0/1 SWR LED on the KPA500 does light up.) > > I have assumed that the 1.2/1 KAT500 SWR LED does not light up is because 1) > the KAT500 threshold for the first SWR LED is 1.2/1 and 2) because no > tuning action has taken place in these circumstances (due to memorized > KAT500 tuning configuration). However, I noticed at the bottom of page 49 > of Fred Cady's book on the KAT500 and the KPA500 it says "VSWR is displayed > even when the tuner is bypasssed". So, I'm confused. Does no SWR LED light > when the SWR is 1.0/1 (or very close to it) because the SWR is below 1.2/1? > > Thanks, > > Brian, K8GRR > > > > -- > Sent from: http://elecraft.365791.n2.nabble.com/ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html