Re: [gentoo-user] Re: heat codes
On Friday 13 Mar 2015 00:38:56 Dale wrote: James wrote: Mick michaelkintzios at gmail.com writes: # sensors radeon-pci-0100 Adapter: PCI adapter temp1:+36.0°C (crit = +120.0°C, hyst = +90.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: 19.97 W (crit = 125.19 W) k10temp-pci-00c3 Adapter: PCI adapter temp1:+24.9°C (high = +70.0°C) (crit = +90.0°C, hyst = +87.0°C) There should be more after these, showing your voltages and various MoBo sensors. Can you check that it87 is actually loaded? lsmod will tell you. Oh, I just noticed this posting; Dale's latest posting caused me to look at the thread again. rc-status shows lm_sensors running, as does ps. but lsmod is empty: Module Size Used by /etc/conf.d/lm_sensors shows: MODULE_0=fam15h_power MODULE_1=it87 MODULE_2=k10temp I think I have it 'compiled in'. Are you sure I should be seeing more information? GA-990FXA-UD3 is the mobo. James I have a 970A-UD3P mobo and I use this under Hardware Monitoring support: AMD Family 10h+ temperature sensor AMD Family 15h processor power ITE IT87xx and compatibles Under bus support: Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC) Our mobo isn't exactly the same but if they use the same chips, those should get you all the info you need. I might add, I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Hope that helps. Dale :-) :-) I don't have the same MoBo and have compiled my corresponding chipset sensor driver as a module. It doesn't load unless I manually modprobe it or set it up in /etc/conf.d/modules. This is how many readings I get: $ sensors radeon-pci-0008 Adapter: PCI adapter temp1:+37.0°C (crit = +120.0°C, hyst = +90.0°C) k10temp-pci-00c3 Adapter: PCI adapter temp1:+36.8°C (high = +70.0°C) (crit = +70.0°C, hyst = +69.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: N/A (crit = 95.09 W) nct6791-isa-0290 Adapter: ISA adapter in0:+1.38 V (min = +0.00 V, max = +1.74 V) in1:+1.03 V (min = +0.00 V, max = +0.00 V) ALARM in2:+3.34 V (min = +0.00 V, max = +0.00 V) ALARM in3:+3.34 V (min = +0.00 V, max = +0.00 V) ALARM in4:+1.01 V (min = +0.00 V, max = +0.00 V) ALARM in5:+2.04 V (min = +0.00 V, max = +0.00 V) ALARM in6:+0.28 V (min = +0.00 V, max = +0.00 V) ALARM in7:+3.44 V (min = +0.00 V, max = +0.00 V) ALARM in8:+3.33 V (min = +0.00 V, max = +0.00 V) ALARM in9:+0.00 V (min = +0.00 V, max = +0.00 V) in10: +0.17 V (min = +0.00 V, max = +0.00 V) ALARM in11: +0.17 V (min = +0.00 V, max = +0.00 V) ALARM in12: +1.01 V (min = +0.00 V, max = +0.00 V) ALARM in13: +1.03 V (min = +0.00 V, max = +0.00 V) ALARM in14: +0.21 V (min = +0.00 V, max = +0.00 V) ALARM fan1: 1036 RPM (min =0 RPM) fan2: 1695 RPM (min =0 RPM) fan3: 1001 RPM (min =0 RPM) SYSTIN: +31.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = thermistor CPUTIN: +47.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor AUXTIN0: +106.0°Csensor = thermistor AUXTIN1: +105.0°Csensor = thermistor AUXTIN2: +105.0°Csensor = thermistor AUXTIN3: +106.0°Csensor = thermistor PCH_CHIP_CPU_MAX_TEMP: +0.0°C PCH_CHIP_TEMP: +0.0°C PCH_CPU_TEMP:+0.0°C PCH_MCH_TEMP:+0.0°C intrusion0:ALARM intrusion1:ALARM beep_enable: disabled HTH. -- Regards, Mick signature.asc Description: This is a digitally signed message part.
Re: [gentoo-user] Re: heat codes
On Thursday 12 March 2015 19:38:56 Dale wrote: I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Does that mean that your gkrellm can't display temperatures? -- Rgds Peter.
Re: [gentoo-user] Re: heat codes
Tuomo Hartikainen wrote: On 150312 1835, Dale wrote: waben...@gmail.com wrote: Something similar happened to me. I accidentally pressed F6 while focused gkrellm but didn't noticed it. Some time later I realized that the fontsize of gkrellm was increased so that it's height doesn't fit to the screen anymore. Fist I thought that it has something to do with the latest update. It took some time till I recognized that I simply had to press F7 to restore the fontsize to its former height. :-) -- Regards wabe Well, you should have seen the look on my face the other day when Firefox went FULL SCREEN. I mean full screen like it does when I hit F and am watching a video. Heck, I didn't have a menu at the top, To this day, I have no clue what I did. I was typing a comment on a social site and all of the sudden, it went sucky. Still no clue but thank goodness it fixed itself after I killed it and restarted. Dale Try pressing F11 in Firefox? ;) I think I tried that. I think I tried all the F* keys. I was also able to ctrl F* to get to another desktop and use a second browser to try and figure the thing out. I tried a few things I found online but none of them worked. Also weird, I was typing normal characters when it went weird on me just like I am in this email. No ctrl, alt or other keys. The closest I got to those was the shift key for capitol letters. I just hope I never run into that again. o_O Dale :-) :-)
Re: [gentoo-user] Re: heat codes
Mick wrote: I don't have the same MoBo and have compiled my corresponding chipset sensor driver as a module. It doesn't load unless I manually modprobe it or set it up in /etc/conf.d/modules. This is how many readings I get: $ sensors radeon-pci-0008 Adapter: PCI adapter temp1:+37.0°C (crit = +120.0°C, hyst = +90.0°C) k10temp-pci-00c3 Adapter: PCI adapter temp1:+36.8°C (high = +70.0°C) (crit = +70.0°C, hyst = +69.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: N/A (crit = 95.09 W) nct6791-isa-0290 Adapter: ISA adapter in0:+1.38 V (min = +0.00 V, max = +1.74 V) in1:+1.03 V (min = +0.00 V, max = +0.00 V) ALARM in2:+3.34 V (min = +0.00 V, max = +0.00 V) ALARM in3:+3.34 V (min = +0.00 V, max = +0.00 V) ALARM in4:+1.01 V (min = +0.00 V, max = +0.00 V) ALARM in5:+2.04 V (min = +0.00 V, max = +0.00 V) ALARM in6:+0.28 V (min = +0.00 V, max = +0.00 V) ALARM in7:+3.44 V (min = +0.00 V, max = +0.00 V) ALARM in8:+3.33 V (min = +0.00 V, max = +0.00 V) ALARM in9:+0.00 V (min = +0.00 V, max = +0.00 V) in10: +0.17 V (min = +0.00 V, max = +0.00 V) ALARM in11: +0.17 V (min = +0.00 V, max = +0.00 V) ALARM in12: +1.01 V (min = +0.00 V, max = +0.00 V) ALARM in13: +1.03 V (min = +0.00 V, max = +0.00 V) ALARM in14: +0.21 V (min = +0.00 V, max = +0.00 V) ALARM fan1: 1036 RPM (min =0 RPM) fan2: 1695 RPM (min =0 RPM) fan3: 1001 RPM (min =0 RPM) SYSTIN: +31.0°C (high = +0.0°C, hyst = +0.0°C) ALARM sensor = thermistor CPUTIN: +47.0°C (high = +80.0°C, hyst = +75.0°C) sensor = thermistor AUXTIN0: +106.0°Csensor = thermistor AUXTIN1: +105.0°Csensor = thermistor AUXTIN2: +105.0°Csensor = thermistor AUXTIN3: +106.0°Csensor = thermistor PCH_CHIP_CPU_MAX_TEMP: +0.0°C PCH_CHIP_TEMP: +0.0°C PCH_CPU_TEMP:+0.0°C PCH_MCH_TEMP:+0.0°C intrusion0:ALARM intrusion1:ALARM beep_enable: disabled HTH. I get things like this: root@fireball / # ls -al /sys/devices/platform/it87.552/ total 0 drwxr-xr-x 4 root root0 Mar 11 19:25 . drwxr-xr-x 12 root root0 Mar 11 19:25 .. -r--r--r-- 1 root root 4096 Mar 13 06:16 alarms lrwxrwxrwx 1 root root0 Mar 11 19:25 driver - ../../../bus/platform/drivers/it87 -rw-r--r-- 1 root root 4096 Mar 13 06:16 driver_override -r--r--r-- 1 root root 4096 Mar 13 06:16 fan1_alarm -rw-r--r-- 1 root root 4096 Mar 4 15:11 fan1_beep -r--r--r-- 1 root root 4096 Mar 11 19:26 fan1_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 fan1_min -r--r--r-- 1 root root 4096 Mar 13 06:16 fan2_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 fan2_beep -r--r--r-- 1 root root 4096 Mar 11 19:26 fan2_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 fan2_min -r--r--r-- 1 root root 4096 Mar 13 06:16 fan3_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 fan3_beep -r--r--r-- 1 root root 4096 Mar 11 19:26 fan3_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 fan3_min -r--r--r-- 1 root root 4096 Mar 13 06:16 fan4_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 fan4_beep -r--r--r-- 1 root root 4096 Mar 13 06:16 fan4_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 fan4_min -r--r--r-- 1 root root 4096 Mar 13 06:16 fan5_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 fan5_beep -r--r--r-- 1 root root 4096 Mar 11 19:26 fan5_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 fan5_min drwxr-xr-x 3 root root0 Mar 11 19:25 hwmon -r--r--r-- 1 root root 4096 Mar 13 06:16 in0_alarm -rw-r--r-- 1 root root 4096 Mar 13 06:16 in0_beep -r--r--r-- 1 root root 4096 Mar 13 06:16 in0_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 in0_max -rw-r--r-- 1 root root 4096 Mar 13 06:16 in0_min -r--r--r-- 1 root root 4096 Mar 13 06:16 in1_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 in1_beep -r--r--r-- 1 root root 4096 Mar 13 06:16 in1_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 in1_max -rw-r--r-- 1 root root 4096 Mar 13 06:16 in1_min -r--r--r-- 1 root root 4096 Mar 13 06:16 in2_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 in2_beep -r--r--r-- 1 root root 4096 Mar 13 06:16 in2_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 in2_max -rw-r--r-- 1 root root 4096 Mar 13 06:16 in2_min -r--r--r-- 1 root root 4096 Mar 13 06:16 in3_alarm -r--r--r-- 1 root root 4096 Mar 13 06:16 in3_beep -r--r--r-- 1 root root 4096 Mar 13 06:16 in3_input -rw-r--r-- 1 root root 4096 Mar 13 06:16 in3_max -rw-r--r-- 1 root root 4096 Mar 13 06:16 in3_min -r--r--r--
Re: [gentoo-user] Re: heat codes
On Friday 13 March 2015 06:27:00 Dale wrote: Peter Humphrey wrote: On Thursday 12 March 2015 19:38:56 Dale wrote: I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Does that mean that your gkrellm can't display temperatures? It's been displaying temps for many years. I posted a list in my reply to Mick. I also can get voltages but don't have it set to show them. I do also monitor temps on the hard drives. That's done through the smart thingy. I don't know what led you to list that directory, but now that I look into my own setup I see I'm using kernel modules too. I know I used to use lm_sensors at one time, but genlop doesn't know about it so I must have omitted it when I last reinstalled. # ls -l /sys/devices/platform total 0 drwxr-xr-x 3 root root0 Mar 13 11:49 alarmtimer drwxr-xr-x 4 root root0 Mar 13 11:49 coretemp.0 drwxr-xr-x 5 root root0 Mar 13 11:49 i8042 drwxr-xr-x 3 root root0 Mar 13 11:49 pcspkr drwxr-xr-x 3 root root0 Mar 13 11:49 platform-framebuffer.0 drwxr-xr-x 3 root root0 Mar 13 11:49 PNP0C0C:00 drwxr-xr-x 2 root root0 Mar 13 11:49 power -rw-r--r-- 1 root root 4.0K Mar 13 11:49 uevent drwxr-xr-x 3 root root0 Mar 13 11:49 vboxdrv.0 -- Rgds Peter.
Re: [gentoo-user] Re: heat codes
Peter Humphrey wrote: On Thursday 12 March 2015 19:38:56 Dale wrote: I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Does that mean that your gkrellm can't display temperatures? It's been displaying temps for many years. I posted a list in my reply to Mick. I also can get voltages but don't have it set to show them. I do also monitor temps on the hard drives. That's done through the smart thingy. Dale :-) :-)
Re: [gentoo-user] Re: heat codes
Peter Humphrey wrote: On Friday 13 March 2015 06:27:00 Dale wrote: Peter Humphrey wrote: On Thursday 12 March 2015 19:38:56 Dale wrote: I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Does that mean that your gkrellm can't display temperatures? It's been displaying temps for many years. I posted a list in my reply to Mick. I also can get voltages but don't have it set to show them. I do also monitor temps on the hard drives. That's done through the smart thingy. I don't know what led you to list that directory, but now that I look into my own setup I see I'm using kernel modules too. I know I used to use lm_sensors at one time, but genlop doesn't know about it so I must have omitted it when I last reinstalled. # ls -l /sys/devices/platform total 0 drwxr-xr-x 3 root root0 Mar 13 11:49 alarmtimer drwxr-xr-x 4 root root0 Mar 13 11:49 coretemp.0 drwxr-xr-x 5 root root0 Mar 13 11:49 i8042 drwxr-xr-x 3 root root0 Mar 13 11:49 pcspkr drwxr-xr-x 3 root root0 Mar 13 11:49 platform-framebuffer.0 drwxr-xr-x 3 root root0 Mar 13 11:49 PNP0C0C:00 drwxr-xr-x 2 root root0 Mar 13 11:49 power -rw-r--r-- 1 root root 4.0K Mar 13 11:49 uevent drwxr-xr-x 3 root root0 Mar 13 11:49 vboxdrv.0 From my understanding, you can use either the kernel drivers or lm-sensors. Many years ago, I sort of got bored installing lm-sensors and running the setup stuff all the time. I seem to recall, you have to do it again when you upgrade the kernel too. Anyway, I started using the kernel drivers and I've been doing it that way ever since. Hey, it works. It also gets updated with each kernel upgrade too. I'm all for what works. It works for me and seems it works for you as well so, yeppie!!! Given I been battling the flu for a few weeks, yeppie is about as good as it gets right now. I never could dance anyway. ;-) Oh, I listed my sensor stuff because Mick listed his. I thought we could compare what we each get. It looks the same to me. I just didn't see the need in posting it twice when odds are you will see both posts anyway. :-) Dale :-) :-)
Re: [gentoo-user] Re: heat codes
On Friday 13 Mar 2015 15:49:38 Dale wrote: Peter Humphrey wrote: On Friday 13 March 2015 06:27:00 Dale wrote: Peter Humphrey wrote: On Thursday 12 March 2015 19:38:56 Dale wrote: I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Does that mean that your gkrellm can't display temperatures? It's been displaying temps for many years. I posted a list in my reply to Mick. I also can get voltages but don't have it set to show them. I do also monitor temps on the hard drives. That's done through the smart thingy. I don't know what led you to list that directory, but now that I look into my own setup I see I'm using kernel modules too. I know I used to use lm_sensors at one time, but genlop doesn't know about it so I must have omitted it when I last reinstalled. # ls -l /sys/devices/platform total 0 drwxr-xr-x 3 root root0 Mar 13 11:49 alarmtimer drwxr-xr-x 4 root root0 Mar 13 11:49 coretemp.0 drwxr-xr-x 5 root root0 Mar 13 11:49 i8042 drwxr-xr-x 3 root root0 Mar 13 11:49 pcspkr drwxr-xr-x 3 root root0 Mar 13 11:49 platform-framebuffer.0 drwxr-xr-x 3 root root0 Mar 13 11:49 PNP0C0C:00 drwxr-xr-x 2 root root0 Mar 13 11:49 power -rw-r--r-- 1 root root 4.0K Mar 13 11:49 uevent drwxr-xr-x 3 root root0 Mar 13 11:49 vboxdrv.0 From my understanding, you can use either the kernel drivers or lm-sensors. Really? I didn't know this. I have installed both, seemingly without any ill effects. Many years ago, I sort of got bored installing lm-sensors and running the setup stuff all the time. I seem to recall, you have to do it again when you upgrade the kernel too. I didn't know this either. Anyway, gkrellm works happily which is what I primarily use, unless I'm login in remotely in which case I just run 'watch -d sensors' if I want to check what's happening on the MoBo. -- Regards, Mick signature.asc Description: This is a digitally signed message part.
Re: [gentoo-user] Re: heat codes
On 150312 1835, Dale wrote: waben...@gmail.com wrote: Something similar happened to me. I accidentally pressed F6 while focused gkrellm but didn't noticed it. Some time later I realized that the fontsize of gkrellm was increased so that it's height doesn't fit to the screen anymore. Fist I thought that it has something to do with the latest update. It took some time till I recognized that I simply had to press F7 to restore the fontsize to its former height. :-) -- Regards wabe Well, you should have seen the look on my face the other day when Firefox went FULL SCREEN. I mean full screen like it does when I hit F and am watching a video. Heck, I didn't have a menu at the top, To this day, I have no clue what I did. I was typing a comment on a social site and all of the sudden, it went sucky. Still no clue but thank goodness it fixed itself after I killed it and restarted. Dale Try pressing F11 in Firefox? ;) -- Tuomo Hartikainen
Re: [gentoo-user] Re: heat codes
Peter Humphrey wrote: On Friday 27 February 2015 21:41:33 waben...@gmail.com wrote: You can switch the numerics on and off by left mouse click into the respective monitor. Well, I'll be damned! I never found that out for myself, not in all those years of using it. So no bug here then. Sorry Dale :) This is funny. I accidentally clicked the thing and later on, accidentally clicked it again to turn it back on. Now, first time, makes me go hmm. Second time, hair puller. It took me a while to figure out what I was accidentally doing to fix it. For a bit, I was scared to put my mouse anywhere near the thing. I wasn't sure what else I might accidentally mess up. Well, now you know. ;-) Dale :-) :-)
Re: [gentoo-user] Re: heat codes
James wrote: Mick michaelkintzios at gmail.com writes: # sensors radeon-pci-0100 Adapter: PCI adapter temp1:+36.0°C (crit = +120.0°C, hyst = +90.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: 19.97 W (crit = 125.19 W) k10temp-pci-00c3 Adapter: PCI adapter temp1:+24.9°C (high = +70.0°C) (crit = +90.0°C, hyst = +87.0°C) There should be more after these, showing your voltages and various MoBo sensors. Can you check that it87 is actually loaded? lsmod will tell you. Oh, I just noticed this posting; Dale's latest posting caused me to look at the thread again. rc-status shows lm_sensors running, as does ps. but lsmod is empty: Module Size Used by /etc/conf.d/lm_sensors shows: MODULE_0=fam15h_power MODULE_1=it87 MODULE_2=k10temp I think I have it 'compiled in'. Are you sure I should be seeing more information? GA-990FXA-UD3 is the mobo. James I have a 970A-UD3P mobo and I use this under Hardware Monitoring support: AMD Family 10h+ temperature sensor AMD Family 15h processor power ITE IT87xx and compatibles Under bus support: Intel PIIX4 and compatible (ATI/AMD/Serverworks/Broadcom/SMSC) Our mobo isn't exactly the same but if they use the same chips, those should get you all the info you need. I might add, I build everything into the kernel and I don't even install lm_sensors. I haven't installed that in ages. Hope that helps. Dale :-) :-)
Re: [gentoo-user] Re: heat codes
On Thursday 12 March 2015 14:40:09 Dale wrote: Peter Humphrey wrote: On Friday 27 February 2015 21:41:33 waben...@gmail.com wrote: You can switch the numerics on and off by left mouse click into the respective monitor. Well, I'll be damned! I never found that out for myself, not in all those years of using it. So no bug here then. Sorry Dale :) This is funny. I accidentally clicked the thing and later on, accidentally clicked it again to turn it back on. Now, first time, makes me go hmm. Second time, hair puller. It took me a while to figure out what I was accidentally doing to fix it. For a bit, I was scared to put my mouse anywhere near the thing. I wasn't sure what else I might accidentally mess up. Well, now you know. ;-) Well, it's just as I always say: you learn something new every day - if you're not careful! :-) -- Rgds Peter.
Re: [gentoo-user] Re: heat codes
Am Donnerstag, 12.03.2015 um 14:40 schrieb Dale rdalek1...@gmail.com: Peter Humphrey wrote: On Friday 27 February 2015 21:41:33 waben...@gmail.com wrote: You can switch the numerics on and off by left mouse click into the respective monitor. Well, I'll be damned! I never found that out for myself, not in all those years of using it. So no bug here then. Sorry Dale :) This is funny. I accidentally clicked the thing and later on, accidentally clicked it again to turn it back on. Now, first time, makes me go hmm. Second time, hair puller. It took me a while to figure out what I was accidentally doing to fix it. For a bit, I was scared to put my mouse anywhere near the thing. I wasn't sure what else I might accidentally mess up. Well, now you know. ;-) Something similar happened to me. I accidentally pressed F6 while focused gkrellm but didn't noticed it. Some time later I realized that the fontsize of gkrellm was increased so that it's height doesn't fit to the screen anymore. Fist I thought that it has something to do with the latest update. It took some time till I recognized that I simply had to press F7 to restore the fontsize to its former height. :-) -- Regards wabe
Re: [gentoo-user] Re: heat codes
waben...@gmail.com wrote: Am Donnerstag, 12.03.2015 um 14:40 schrieb Dale rdalek1...@gmail.com: Peter Humphrey wrote: On Friday 27 February 2015 21:41:33 waben...@gmail.com wrote: You can switch the numerics on and off by left mouse click into the respective monitor. Well, I'll be damned! I never found that out for myself, not in all those years of using it. So no bug here then. Sorry Dale :) This is funny. I accidentally clicked the thing and later on, accidentally clicked it again to turn it back on. Now, first time, makes me go hmm. Second time, hair puller. It took me a while to figure out what I was accidentally doing to fix it. For a bit, I was scared to put my mouse anywhere near the thing. I wasn't sure what else I might accidentally mess up. Well, now you know. ;-) Something similar happened to me. I accidentally pressed F6 while focused gkrellm but didn't noticed it. Some time later I realized that the fontsize of gkrellm was increased so that it's height doesn't fit to the screen anymore. Fist I thought that it has something to do with the latest update. It took some time till I recognized that I simply had to press F7 to restore the fontsize to its former height. :-) -- Regards wabe Well, you should have seen the look on my face the other day when Firefox went FULL SCREEN. I mean full screen like it does when I hit F and am watching a video. Heck, I didn't have a menu at the top, To this day, I have no clue what I did. I was typing a comment on a social site and all of the sudden, it went sucky. Still no clue but thank goodness it fixed itself after I killed it and restarted. Dale :-) :-)
Re: [gentoo-user] Re: heat codes
On Thu, 12 Mar 2015 22:38:33 +, Peter Humphrey wrote: Well, it's just as I always say: you learn something new every day - if you're not careful! :-) As the old saying goes: experience is what you get when you didn't get what you wanted :) -- Neil Bothwick I'm Pink, Therefore I'm Spam pgpPTdscr3tFO.pgp Description: OpenPGP digital signature
[gentoo-user] Re: heat codes
Mick michaelkintzios at gmail.com writes: # sensors radeon-pci-0100 Adapter: PCI adapter temp1:+36.0°C (crit = +120.0°C, hyst = +90.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: 19.97 W (crit = 125.19 W) k10temp-pci-00c3 Adapter: PCI adapter temp1:+24.9°C (high = +70.0°C) (crit = +90.0°C, hyst = +87.0°C) There should be more after these, showing your voltages and various MoBo sensors. Can you check that it87 is actually loaded? lsmod will tell you. Oh, I just noticed this posting; Dale's latest posting caused me to look at the thread again. rc-status shows lm_sensors running, as does ps. but lsmod is empty: Module Size Used by /etc/conf.d/lm_sensors shows: MODULE_0=fam15h_power MODULE_1=it87 MODULE_2=k10temp I think I have it 'compiled in'. Are you sure I should be seeing more information? GA-990FXA-UD3 is the mobo. James
Re: [gentoo-user] Re: heat codes
On Friday 27 February 2015 21:41:33 waben...@gmail.com wrote: You can switch the numerics on and off by left mouse click into the respective monitor. Well, I'll be damned! I never found that out for myself, not in all those years of using it. So no bug here then. Sorry Dale :) -- Rgds Peter.
Re: [gentoo-user] Re: heat codes
On Thursday 26 Feb 2015 20:13:07 James wrote: I'm not sure how to moinor the CPU (8 cores) temperature and if it is a calculated (estimated value) or a real temp? # sensors radeon-pci-0100 Adapter: PCI adapter temp1:+36.0°C (crit = +120.0°C, hyst = +90.0°C) fam15h_power-pci-00c4 Adapter: PCI adapter power1: 19.97 W (crit = 125.19 W) k10temp-pci-00c3 Adapter: PCI adapter temp1:+24.9°C (high = +70.0°C) (crit = +90.0°C, hyst = +87.0°C) There should be more after these, showing your voltages and various MoBo sensors. Can you check that it87 is actually loaded? lsmod will tell you. -- Regards, Mick signature.asc Description: This is a digitally signed message part.
Re: [gentoo-user] Re: heat codes
Am Freitag, 27.02.2015 um 09:43 schrieb Peter Humphrey pe...@prh.myzen.co.uk: On Friday 27 February 2015 09:02:18 Neil Bothwick wrote: On Fri, 27 Feb 2015 02:27:03 -0600, Dale wrote: Yes, I have two instances of it running permanently too. Though I think James is right too, in that it does still have the odd bug. I haven't had any trouble with mine. It just sits there and runs until I logout. What is this bug it suffers from? Yay! We've finally found some software that works perfectly for Dale yet shows bugs for other people! You're slipping, Dale! :) Just a minor thing, Dale. Each curve plotted - of, say, traffic over eth0 - is supposed to show a numerical value in the upper left corner, but from time to time one of those will stop being shown. It then stays that way until I remove my .gkrellm2 directory and set the program up again. You can switch the numerics on and off by left mouse click into the respective monitor. Regards wabe
Re: [gentoo-user] Re: heat codes
Peter Humphrey wrote: On Thursday 26 February 2015 19:48:06 Dale wrote: While it has been a while since I used gkrellm to monitor a remote system, I use it every day to monitor my system I sit at. Keep in mind, not much changes on how gkrellm works. It looks for temp/fan/CPU/memory etc info and displays it. I'm not sure it requires a whole lot of updating to do that especially given it has worked fine here for ages and not much has really changed. Yes, I have two instances of it running permanently too. Though I think James is right too, in that it does still have the odd bug. I haven't had any trouble with mine. It just sits there and runs until I logout. What is this bug it suffers from? Dale :-) :-)
Re: [gentoo-user] Re: heat codes
On Fri, 27 Feb 2015 02:27:03 -0600, Dale wrote: Yes, I have two instances of it running permanently too. Though I think James is right too, in that it does still have the odd bug. I haven't had any trouble with mine. It just sits there and runs until I logout. What is this bug it suffers from? Yay! We've finally found some software that works perfectly for Dale yet shows bugs for other people! You're slipping, Dale! -- Neil Bothwick In the begining, there was nothing. And God said Let there be light and there was light. There was still nothing, but you could see it better. pgpqCKianIEJO.pgp Description: OpenPGP digital signature
Re: [gentoo-user] Re: heat codes
On Friday 27 February 2015 09:02:18 Neil Bothwick wrote: On Fri, 27 Feb 2015 02:27:03 -0600, Dale wrote: Yes, I have two instances of it running permanently too. Though I think James is right too, in that it does still have the odd bug. I haven't had any trouble with mine. It just sits there and runs until I logout. What is this bug it suffers from? Yay! We've finally found some software that works perfectly for Dale yet shows bugs for other people! You're slipping, Dale! :) Just a minor thing, Dale. Each curve plotted - of, say, traffic over eth0 - is supposed to show a numerical value in the upper left corner, but from time to time one of those will stop being shown. It then stays that way until I remove my .gkrellm2 directory and set the program up again. Oh, and the Invisible theme stopped being invisible when KDE-4.0 was first allowed to escape. I reported it at the time, but nothing's happened as far as I can see. Nothing major, as I said. I can live with it. -- Rgds Peter.
Re: [gentoo-user] Re: heat codes
Neil Bothwick wrote: On Fri, 27 Feb 2015 02:27:03 -0600, Dale wrote: Yes, I have two instances of it running permanently too. Though I think James is right too, in that it does still have the odd bug. I haven't had any trouble with mine. It just sits there and runs until I logout. What is this bug it suffers from? Yay! We've finally found some software that works perfectly for Dale yet shows bugs for other people! You're slipping, Dale! I was wanting to test it to see if it would screw up with me too. ROFL I figure I must have left something out somewhere. ;-) Dale :-) :-)
Re: [gentoo-user] Re: heat codes
On Thursday 26 February 2015 19:48:06 Dale wrote: While it has been a while since I used gkrellm to monitor a remote system, I use it every day to monitor my system I sit at. Keep in mind, not much changes on how gkrellm works. It looks for temp/fan/CPU/memory etc info and displays it. I'm not sure it requires a whole lot of updating to do that especially given it has worked fine here for ages and not much has really changed. Yes, I have two instances of it running permanently too. Though I think James is right too, in that it does still have the odd bug. It was the remote part that I wasn't sure about. I know it used to have that feature and if it still does, the remote part works just like the local part does. You just tell it to monitor something other than the system you are sitting at. $ gkrellm -s host Then set it up the same way as you would the local one. KDE even knows to restart it along with other progs, which is more than can be said for Chromium. -- Rgds Peter.
Re: [gentoo-user] Re: heat codes
Am 27.02.2015 um 02:23 schrieb James: Volker Armin Hemmann volkerarmin at googlemail.com writes: em, but you are already monitoring it! Maybe. It hard to tell if there are more than one temperature sensor, what buss interfacet they are on and if it is a calculated or esitmated or actual temperature sensor. it pretty much tells you all that with its name. And for radeon - there is only one. Does anyone with similar hardware have a more extensive list? no, that is all you got. That's pretty sad. All that hardware and 3 temps What I'd really like is a very fast (real time?) gui to watch you won't get that, because the senors don't update in 'realtime'. Sure. But if I knew of a relatively consistent delay semantic, use the command below and watch for changes. Some boards update every second, some every three seconds. I could align the delays in temperature sensing with what's going on with code compiling or execution; even if it is a rough estimate. watch -n1 sensors. not bad. for quick checks. Works even without systemd. Shocking, I know. As usual, your insight and singular wit makes for pleasurable reading. thx, James
[gentoo-user] Re: heat codes
James wireless at tampabay.rr.com writes:
modprobe: FATAL: Module i2c-piix4 not found.
Failed to load module i2c-piix4.
OK, so I found this code and added it to the kernel.
Next adapter: Radeon i2c bit bus 0x90 (i2c-0)
Do you want to scan it? (yes/NO/selectively): yes
{through (i2c-7) all failed.
No luck on finding/configuring the radeon temperature
sensors.
So lm_sensors only found these modules:
MODULE_0=fam15h_power [ OK ]
MODULE_1=it87 [ OK ]
MODULE_2=k10temp[ OK ]
Does anyone with similar hardware have a more extensive list?
I'm not sure how to moinor the CPU (8 cores) temperature
and if it is a calculated (estimated value) or a real temp?
# sensors
radeon-pci-0100
Adapter: PCI adapter
temp1:+36.0°C (crit = +120.0°C, hyst = +90.0°C)
fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 19.97 W (crit = 125.19 W)
k10temp-pci-00c3
Adapter: PCI adapter
temp1:+24.9°C (high = +70.0°C)
(crit = +90.0°C, hyst = +87.0°C)
What I'd really like is a very fast (real time?) gui to watch
these temperatures as certain portions of codes are compile or executed.
Right now I'm running lxde, but my migration to lxqt (QT5) should
begin very soon so any QT5_ish gui would be very cool too.
https://wiki.archlinux.org/index.php/fan_speed_control
James
Re: [gentoo-user] Re: heat codes
Am 26.02.2015 um 21:13 schrieb James:
James wireless at tampabay.rr.com writes:
modprobe: FATAL: Module i2c-piix4 not found.
Failed to load module i2c-piix4.
OK, so I found this code and added it to the kernel.
Next adapter: Radeon i2c bit bus 0x90 (i2c-0)
Do you want to scan it? (yes/NO/selectively): yes
{through (i2c-7) all failed.
No luck on finding/configuring the radeon temperature
sensors.
em, but you are already monitoring it!
So lm_sensors only found these modules:
MODULE_0=fam15h_power [ OK ]
MODULE_1=it87 [ OK ]
MODULE_2=k10temp[ OK ]
which looks good.
Does anyone with similar hardware have a more extensive list?
no, that is all you got.
I'm not sure how to moinor the CPU (8 cores) temperature
and if it is a calculated (estimated value) or a real temp?
# sensors
radeon-pci-0100
Adapter: PCI adapter
temp1:+36.0°C (crit = +120.0°C, hyst = +90.0°C)
see? radeon. Monitored. Just move along.
fam15h_power-pci-00c4
Adapter: PCI adapter
power1: 19.97 W (crit = 125.19 W)
k10temp-pci-00c3
Adapter: PCI adapter
temp1:+24.9°C (high = +70.0°C)
(crit = +90.0°C, hyst = +87.0°C)
What I'd really like is a very fast (real time?) gui to watch
these temperatures as certain portions of codes are compile or executed.
you won't get that, because the senors don't update in 'realtime'.
Right now I'm running lxde, but my migration to lxqt (QT5) should
begin very soon so any QT5_ish gui would be very cool too.
watch -n1 sensors.
Works even without systemd. Shocking, I know.
[gentoo-user] Re: heat codes
Volker Armin Hemmann volkerarmin at googlemail.com writes: em, but you are already monitoring it! Maybe. It hard to tell if there are more than one temperature sensor, what buss interfacet they are on and if it is a calculated or esitmated or actual temperature sensor. Does anyone with similar hardware have a more extensive list? no, that is all you got. That's pretty sad. All that hardware and 3 temps What I'd really like is a very fast (real time?) gui to watch you won't get that, because the senors don't update in 'realtime'. Sure. But if I knew of a relatively consistent delay semantic, I could align the delays in temperature sensing with what's going on with code compiling or execution; even if it is a rough estimate. watch -n1 sensors. not bad. for quick checks. Works even without systemd. Shocking, I know. As usual, your insight and singular wit makes for pleasurable reading. thx, James
[gentoo-user] Re: heat codes
Dale rdalek1967 at gmail.com writes: I need to monitor this hardware for temperatures, including logging of temperatures, on as wide array of temperature sensors that is possible with kernel 3.18.6-gentoo.) I'm not sure if this is still available or not but doesn't gkrellm do this sort of thing? I used it to monitor another rig several years ago. May be worth looking into. Dale That (gkrellm) codebase looks old, un-maintained and wee bit clumsy. It's interesting to examine for ideas. I think I'm going with something a bit more embedded inspired, for speed and portability reasons. I also have since found this interesting piece of code; sys-cluster/ganglia First glance, it's a bit heavy-handed for my needs. I've gotta keep looking before I decide on a path forward for RT temperature monitoring, dB tracking and problem profiling. Thanks! James
Re: [gentoo-user] Re: heat codes
James wrote: Dale rdalek1967 at gmail.com writes: I need to monitor this hardware for temperatures, including logging of temperatures, on as wide array of temperature sensors that is possible with kernel 3.18.6-gentoo.) I'm not sure if this is still available or not but doesn't gkrellm do this sort of thing? I used it to monitor another rig several years ago. May be worth looking into. Dale That (gkrellm) codebase looks old, un-maintained and wee bit clumsy. It's interesting to examine for ideas. I think I'm going with something a bit more embedded inspired, for speed and portability reasons. I also have since found this interesting piece of code; sys-cluster/ganglia First glance, it's a bit heavy-handed for my needs. I've gotta keep looking before I decide on a path forward for RT temperature monitoring, dB tracking and problem profiling. Thanks! James While it has been a while since I used gkrellm to monitor a remote system, I use it every day to monitor my system I sit at. Keep in mind, not much changes on how gkrellm works. It looks for temp/fan/CPU/memory etc info and displays it. I'm not sure it requires a whole lot of updating to do that especially given it has worked fine here for ages and not much has really changed. It was the remote part that I wasn't sure about. I know it used to have that feature and if it still does, the remote part works just like the local part does. You just tell it to monitor something other than the system you are sitting at. Sorry I wasn't more clear in my first message. Dale :-) :-)
