Re: [H] Non booting case
Forget Duncan's insight, well intentioned but only vaguely accurate. That's not how you'd go about testing this issue since the power good line of the PSU is showing OK as the system powers up & stays on depending on case orientation. When you say "start" I assume you mean "power" button jumper header on the mobo, I would not concern myself with metering the voltage across this jumper. Shorting it either powers on the system or it doesn't. Normally diagnosis of it & the switch is manually shorting the mobo's powersw pins but you've replaced the switch anyway. Most likely something is loose that should be screwed down or the ATX power connector is not seated solidly into the mobo socket. Hence stand it on end, something shifts. Sam Franc wrote: Thanks, Do you have any idea what pin on the 24 pin power connector provides the connection to turn on the power supply. Sam
Re: [H] Non booting case
I am at a standstill on my checking. Would there be any danger in using a second known good psu and just plugging in the 24 pin main supply cable and leave the HD power on the old power supply? This would show up if there was a break in one of the power wires in the old power supply without just changing ir all out. Sam FORC5 wrote: I have always used pins 16 and 10 At 01:10 PM 11/23/2008, DHSinclair Poked the stick with: Sam, http://en.wikipedia.org/wiki/ATX IIRC, if you jumper pins 15 and 16, you will do the same thing the m/b's internal switching logic does to turn the system on. Please do not hold me to my choice of pins. Others in the collective have much more experience with this and may offer other choices of pins. And, in all truth, I have not really seen all that many true internal wiring problems in modern PC cases since ~1975. I have only seen one m/b whose internal switching logic went bad or died. I would focus on the m/b ground logic and/or the psu. Jumpering the 24-pin power connector should really be a last ditch kind of trial. Best, Duncan At 10:01 11/23/2008 -0800, you wrote: Thanks, Do you have any idea what pin on the 24 pin power connector provides the connection to turn on the power supply. Sam DHSinclair wrote: Sam, I have found that this problem involves at least 2 things. One thing is the m/b itself The other thing is that internal case wiring. For the m/b, what you need to do is make certain that the m/b is tight (?) to its' tray. Or, make certain that it is screwed down tight, however. It is most probably a "ground" thing. Next, case wires and their looms are notorious for problems. Stuff just happens. Your off/on switch could be fine, but the signal is not making it to the m/b due to bad wiring. A Look/SEE. That is the best I can share. I do not know Gigabyte m/b's. I have never seen an Antec case. Best, Duncan At 17:50 11/22/2008 -0800, you wrote: I have an Antec case with a Gigabyte mobo that has a strange boot operation. If I press the start button and it doesn't boot, I turn the case on it's side and it starts. I can turn the tower back on it's base and it continues to run fine. I turn it off for the night and it may start fine in the upright position or I may have to turn it in it's side to get it to boot. I have replaced the start switch with no difference in operation. What voltage should be across the start switch terminals? Any ideas of what to explore? I know this is a crazy problem with no obvious exploration paths. Sam No virus found in this incoming message. Checked by AVG - http://www.avg.com Version: 8.0.175 / Virus Database: 270.9.9/1804 - Release Date: 11/21/2008 6:24 PM -- Sam Franc On the Oregon Coast I must be willing to give up what I am in order to become what I will be.-Einstein No virus found in this incoming message. Checked by AVG - http://www.avg.com Version: 8.0.175 / Virus Database: 270.9.9/1807 - Release Date: 11/23/2008 10:59 AM -- Sam Franc On the Oregon Coast I must be willing to give up what I am in order to become what I will be.-Einstein
Re: [H] Non booting case
I have always used pins 16 and 10 At 01:10 PM 11/23/2008, DHSinclair Poked the stick with: >Sam, >http://en.wikipedia.org/wiki/ATX > >IIRC, if you jumper pins 15 and 16, you will do the same thing the m/b's >internal switching logic does to turn the system on. Please do not hold me to >my choice of pins. Others in the collective have much more experience with >this and may offer other choices of pins. > >And, in all truth, I have not really seen all that many true internal wiring >problems in modern PC cases since ~1975. I have only seen one m/b whose >internal switching logic went bad or died. I would focus on the m/b ground >logic and/or the psu. Jumpering the 24-pin power connector should really be a >last ditch kind of trial. >Best, >Duncan > > >At 10:01 11/23/2008 -0800, you wrote: >>Thanks, >>Do you have any idea what pin on the 24 pin power connector provides the >>connection to turn on the power supply. >>Sam >> >>DHSinclair wrote: >>>Sam, >>>I have found that this problem involves at least 2 things. >>>One thing is the m/b itself >>>The other thing is that internal case wiring. >>>For the m/b, what you need to do is make certain that the m/b is tight (?) >>>to its' tray. Or, make certain that it is screwed down tight, however. It >>>is most probably a "ground" thing. >>>Next, case wires and their looms are notorious for problems. Stuff just >>>happens. Your off/on switch could be fine, but the signal is not making it >>>to the m/b due to bad wiring. A Look/SEE. >>>That is the best I can share. >>>I do not know Gigabyte m/b's. I have never seen an Antec case. >>>Best, >>>Duncan >>> >>>At 17:50 11/22/2008 -0800, you wrote: I have an Antec case with a Gigabyte mobo that has a strange boot operation. If I press the start button and it doesn't boot, I turn the case on it's side and it starts. I can turn the tower back on it's base and it continues to run fine. I turn it off for the night and it may start fine in the upright position or I may have to turn it in it's side to get it to boot. I have replaced the start switch with no difference in operation. What voltage should be across the start switch terminals? Any ideas of what to explore? I know this is a crazy problem with no obvious exploration paths. Sam >>> >>> >>> >>> >>>No virus found in this incoming message. >>>Checked by AVG - http://www.avg.com Version: 8.0.175 / Virus Database: >>>270.9.9/1804 - Release Date: 11/21/2008 6:24 PM >>> >> >>-- >>Sam Franc >>On the Oregon Coast >>I must be willing to give up what I am >>in order to become what I will be.-Einstein -- Tallyho ! ]:8) Taglines below ! -- Shouldn't you be doing something useful?
Re: [H] Non booting case
Sam, http://en.wikipedia.org/wiki/ATX IIRC, if you jumper pins 15 and 16, you will do the same thing the m/b's internal switching logic does to turn the system on. Please do not hold me to my choice of pins. Others in the collective have much more experience with this and may offer other choices of pins. And, in all truth, I have not really seen all that many true internal wiring problems in modern PC cases since ~1975. I have only seen one m/b whose internal switching logic went bad or died. I would focus on the m/b ground logic and/or the psu. Jumpering the 24-pin power connector should really be a last ditch kind of trial. Best, Duncan At 10:01 11/23/2008 -0800, you wrote: Thanks, Do you have any idea what pin on the 24 pin power connector provides the connection to turn on the power supply. Sam DHSinclair wrote: Sam, I have found that this problem involves at least 2 things. One thing is the m/b itself The other thing is that internal case wiring. For the m/b, what you need to do is make certain that the m/b is tight (?) to its' tray. Or, make certain that it is screwed down tight, however. It is most probably a "ground" thing. Next, case wires and their looms are notorious for problems. Stuff just happens. Your off/on switch could be fine, but the signal is not making it to the m/b due to bad wiring. A Look/SEE. That is the best I can share. I do not know Gigabyte m/b's. I have never seen an Antec case. Best, Duncan At 17:50 11/22/2008 -0800, you wrote: I have an Antec case with a Gigabyte mobo that has a strange boot operation. If I press the start button and it doesn't boot, I turn the case on it's side and it starts. I can turn the tower back on it's base and it continues to run fine. I turn it off for the night and it may start fine in the upright position or I may have to turn it in it's side to get it to boot. I have replaced the start switch with no difference in operation. What voltage should be across the start switch terminals? Any ideas of what to explore? I know this is a crazy problem with no obvious exploration paths. Sam No virus found in this incoming message. Checked by AVG - http://www.avg.com Version: 8.0.175 / Virus Database: 270.9.9/1804 - Release Date: 11/21/2008 6:24 PM -- Sam Franc On the Oregon Coast I must be willing to give up what I am in order to become what I will be.-Einstein
Re: [H] Non booting case
http://bsd-unix.net/seitz/screenshots/atx-poweron-withoutmobo.png On Sun, Nov 23, 2008 at 10:01:04AM -0800, Sam Franc wrote: > Thanks, > Do you have any idea what pin on the 24 pin power connector provides the > connection to turn on the power supply. > Sam > > DHSinclair wrote: > > Sam, > > I have found that this problem involves at least 2 things. > > One thing is the m/b itself > > The other thing is that internal case wiring. > > For the m/b, what you need to do is make certain that the m/b is tight > > (?) to its' tray. Or, make certain that it is screwed down tight, > > however. It is most probably a "ground" thing. > > Next, case wires and their looms are notorious for problems. Stuff > > just happens. Your off/on switch could be fine, but the signal is not > > making it to the m/b due to bad wiring. A Look/SEE. > > That is the best I can share. > > I do not know Gigabyte m/b's. I have never seen an Antec case. > > Best, > > Duncan > > > > At 17:50 11/22/2008 -0800, you wrote: > >> I have an Antec case with a Gigabyte mobo that has a strange boot > >> operation. > >> If I press the start button and it doesn't boot, I turn the case on > >> it's side and it starts. > >> I can turn the tower back on it's base and it continues to run fine. > >> I turn it off for the night and it may start fine in the upright > >> position or I may have to turn it in it's side to get it to boot. > >> I have replaced the start switch with no difference in operation. > >> What voltage should be across the start switch terminals? > >> Any ideas of what to explore? > >> I know this is a crazy problem with no obvious exploration paths. > >> Sam > >> > >> > >> > >> > >> > >> > > > > > > > > > > No virus found in this incoming message. > > Checked by AVG - http://www.avg.com > > Version: 8.0.175 / Virus Database: 270.9.9/1804 - Release Date: 11/21/2008 > > 6:24 PM > > > > > > -- > Sam Franc > On the Oregon Coast > I must be willing to give up what I am > in order to become what I will be.-Einstein -- Bryan G. Seitz
Re: [H] Non booting case
Thanks, Do you have any idea what pin on the 24 pin power connector provides the connection to turn on the power supply. Sam DHSinclair wrote: Sam, I have found that this problem involves at least 2 things. One thing is the m/b itself The other thing is that internal case wiring. For the m/b, what you need to do is make certain that the m/b is tight (?) to its' tray. Or, make certain that it is screwed down tight, however. It is most probably a "ground" thing. Next, case wires and their looms are notorious for problems. Stuff just happens. Your off/on switch could be fine, but the signal is not making it to the m/b due to bad wiring. A Look/SEE. That is the best I can share. I do not know Gigabyte m/b's. I have never seen an Antec case. Best, Duncan At 17:50 11/22/2008 -0800, you wrote: I have an Antec case with a Gigabyte mobo that has a strange boot operation. If I press the start button and it doesn't boot, I turn the case on it's side and it starts. I can turn the tower back on it's base and it continues to run fine. I turn it off for the night and it may start fine in the upright position or I may have to turn it in it's side to get it to boot. I have replaced the start switch with no difference in operation. What voltage should be across the start switch terminals? Any ideas of what to explore? I know this is a crazy problem with no obvious exploration paths. Sam No virus found in this incoming message. Checked by AVG - http://www.avg.com Version: 8.0.175 / Virus Database: 270.9.9/1804 - Release Date: 11/21/2008 6:24 PM -- Sam Franc On the Oregon Coast I must be willing to give up what I am in order to become what I will be.-Einstein
Re: [H] Non booting case
Hello Sam, Saturday, November 22, 2008, 7:50:51 PM, you wrote: > I have an Antec case with a Gigabyte mobo that has a strange boot operation. > If I press the start button and it doesn't boot, I turn the case on it's > side and it starts. > I can turn the tower back on it's base and it continues to run fine. > I turn it off for the night and it may start fine in the upright > position or I may have to turn it in it's side to get it to boot. > I have replaced the start switch with no difference in operation. > What voltage should be across the start switch terminals? > Any ideas of what to explore? > I know this is a crazy problem with no obvious exploration paths. > Sam Like others have said, sounds like it's grounding out. Replace/Swap the PSU for diagnostic value. -- Regards, joeuser - Still looking for the 'any' key... "...now these points of data make a beautiful line..."
Re: [H] Non booting case
Sam, I once had an old 386 computer I sold to a friend. He called after setting it up that it wasn't working. I took it home, openned it up and checked everything. It was working fine. I closed up the case and returned it, and again, it did not work for him. Thinking it was something in his home setup, I made a housecall. Took the system apart to troubleshoot and it was working fine. Put it back together, and it stopped working. Finally, I saw the problem! Removing the case cover reduced stress somewhere in the motherboard that allowed the system to boot. As soon as I attached to case cover, the motherboard was strained and would not boot. I replaced the motherboard and all was well, again. Long story short, does turning the case on its side de-stress some part of the motherboard or some other connection. Just a thought and wag. Good luck. Jim Maki [EMAIL PROTECTED] > -Original Message- > From: Sam Franc > I have an Antec case with a Gigabyte mobo that has a strange > boot operation. > If I press the start button and it doesn't boot, I turn the > case on it's side and it starts. > I can turn the tower back on it's base and it continues to run fine. > I turn it off for the night and it may start fine in the > upright position or I may have to turn it in it's side to get > it to boot. > I have replaced the start switch with no difference in operation. > What voltage should be across the start switch terminals? > Any ideas of what to explore? > I know this is a crazy problem with no obvious exploration paths. > Sam
Re: [H] Non booting case
Sam, I have found that this problem involves at least 2 things. One thing is the m/b itself The other thing is that internal case wiring. For the m/b, what you need to do is make certain that the m/b is tight (?) to its' tray. Or, make certain that it is screwed down tight, however. It is most probably a "ground" thing. Next, case wires and their looms are notorious for problems. Stuff just happens. Your off/on switch could be fine, but the signal is not making it to the m/b due to bad wiring. A Look/SEE. That is the best I can share. I do not know Gigabyte m/b's. I have never seen an Antec case. Best, Duncan At 17:50 11/22/2008 -0800, you wrote: I have an Antec case with a Gigabyte mobo that has a strange boot operation. If I press the start button and it doesn't boot, I turn the case on it's side and it starts. I can turn the tower back on it's base and it continues to run fine. I turn it off for the night and it may start fine in the upright position or I may have to turn it in it's side to get it to boot. I have replaced the start switch with no difference in operation. What voltage should be across the start switch terminals? Any ideas of what to explore? I know this is a crazy problem with no obvious exploration paths. Sam
[H] Non booting case
I have an Antec case with a Gigabyte mobo that has a strange boot operation. If I press the start button and it doesn't boot, I turn the case on it's side and it starts. I can turn the tower back on it's base and it continues to run fine. I turn it off for the night and it may start fine in the upright position or I may have to turn it in it's side to get it to boot. I have replaced the start switch with no difference in operation. What voltage should be across the start switch terminals? Any ideas of what to explore? I know this is a crazy problem with no obvious exploration paths. Sam