[Histonet] RE: Re water problem

2010-07-26 Thread Goins, Tresa
Thanks for the great tip Steve - it works great!


Tresa Goins
Veterinary Diagnostic Lab
Department of Livestock
Bozeman, Montana



-Original Message-
From: histonet-boun...@lists.utsouthwestern.edu 
[mailto:histonet-boun...@lists.utsouthwestern.edu] On Behalf Of Steven Weston
Sent: Sunday, July 25, 2010 9:50 PM
To: histonet list
Subject: [Histonet] Re water problem

We had this problem when we started using APTS coated slides and left out 
adhesive from the water bath. A simple solution I have found is to add a single 
drop of triton x100 (or similar detergent) to my full water bath and mix before 
heating the water. This reduces the surface tension of the water and allows it 
to run off the slide.
Regards
Steve weston
Menzies Research Institute
Hobart Tasmania, Australia
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


Re: [Histonet] Artifacts in histology section

2010-07-26 Thread Kim . Donadio
It's very difficult to diagnosis a problem such as this without hands on. 
But one thing that I noticed years ago that was so simple could cause 
this. A build up of tissues on the back of the blade holder. Worth a look. 





Kim Donadio 
Pathology Supervisor
Baptist Hospital
1000 W Moreno St.
Pensacola FL 32501
Phone (850) 469-7718
Fax (850) 434-4996



Joseph Saby saby_josep...@yahoo.com 
Sent by: histonet-boun...@lists.utsouthwestern.edu
07/25/2010 12:49 PM

To
Aazath Raj aaz...@hotmail.com, histonet@lists.utsouthwestern.edu
cc

Subject
Re: [Histonet] Artifacts in histology section






What you are describing might be microchatter.  These will be sharp 
parallel 
lines/cracks that run parallel to the knife edge and are only visible 
under the 
microscope.

The usuall cause is a combination of overprocessing and rough facing that 
is too 
aggressive and/or with too dull a blade.  Overprocessing makes the tissue 
very 
hard and somewhat brittle.  The thick sections/dull knife cause the tissue 
to 
compress and then release, causing the chatter.  The actual danage is in 
the 
block face.

Once you have the problem in a block, if the tissue is thick enough, you 
might 
be able to repeatedly soak the block in ice water and gently (with a 
fairly 
sharp knife) reface.  With luck, you might be able to get through the 
damaged 
block face.  


Another artifact I have seen is similar, but the chatter appears very 
blurry.  
This is usually caused be poor fixation/processing, then oversoaking the 
blocks 
after facing.  The trick here is to reface the block, then chill it 
without 
exposure to water.  I've sectioned such blocks after placing them in a 
freezer 
to chill them thoroughly.  This will help to obtain a section, but may not 
fix 
the staining problems that might show up later.  


Good luck!

Joe Saby, BA HT





From: Aazath Raj aaz...@hotmail.com
To: histonet@lists.utsouthwestern.edu
Sent: Fri, July 23, 2010 11:26:28 AM
Subject: [Histonet] Artifacts in histology section



Dear Friends,

  I am an Histology Technologist. I am having a problem 
here,while 
sectioning am not seeing and scoring artifacts on the section but in the 
microscope am seeing a tearing artifacts particularly in endoscopy 
biopsies. am 
not able to locate where is the problem,is that because of blades or due 
to 
micro-crystallization of wax or due to any processing problem. Its not 
consistently in all but i get it on some blocks every  day. Can any one 
help me 
in sorting it out. If anybody is interested in will send the picture of 
those 
section.





with regards,

Aazathraj.P

Technical Officer,

Apollo Hospitals-chennai

India.

aaz...@hotmail.com



_
The latest in fashion and style in MSN Lifestyle
http://lifestyle.in.msn.com/___

Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet



 
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet



-
All electronic data transmissions originating from or sent to
Baptist Health Care Corporation (BHC) are subject to monitoring.
This message along with any attached data, are the confidential and
proprietary communications of BHC and are intended to be received
only by the individual or individuals to whom the message has been
addressed. If the reader of this message is not the intended
recipient, please take notice that any use, copying, printing,
forwarding or distribution of this message, in any form, is
strictly prohibited and may violate State or Federal Law. If you
have received this transmission in error, please delete or destroy
all copies of this message.  For questions, contact the BHC Privacy
Officer at (850) 434-4472.  Rev.10/07.
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] Special Stain Storage

2010-07-26 Thread kristen arvidson
Hello All,
We were recently inspected by CLIA and our inspector noticed that we didn't 
have reagent storage temperatures written in our Special Stains procedures.  We 
do our stains by hand so we do have some stored in the refrigerator and others 
stored at room temp.  I went through some of the Histo books and I cannot find 
any specifics on storage of reagents.  Any suggestions??
 
Thanks!!
Kristen



___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


RE: [Histonet] Special Stain Storage

2010-07-26 Thread Podawiltz, Thomas
That is a new one on me. It has never come up during any of our inspections. 

 
Tom Podawiltz HT (ASCP) 
Histology Section Head/Laboratory Safety Officer
LRGHealthcare




-Original Message-
From: histonet-boun...@lists.utsouthwestern.edu 
[mailto:histonet-boun...@lists.utsouthwestern.edu] On Behalf Of kristen arvidson
Sent: Monday, July 26, 2010 12:08 PM
To: histonet
Subject: [Histonet] Special Stain Storage

Hello All,
We were recently inspected by CLIA and our inspector noticed that we didn't 
have reagent storage temperatures written in our Special Stains procedures.  We 
do our stains by hand so we do have some stored in the refrigerator and others 
stored at room temp.  I went through some of the Histo books and I cannot find 
any specifics on storage of reagents.  Any suggestions??
 
Thanks!!
Kristen


  
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet
THIS MESSAGE IS CONFIDENTIAL.  
This e-mail message and any attachments are proprietary and confidential 
information intended only for the use of the recipient(s) named above. If you 
are not the intended recipient, you may not print,distribute, or copy this 
message or any attachments.  If you have received this communication in error, 
please notify the sender by return e-mail and delete this message and any 
attachments from your computer. Any views or opinions expressed are solely 
those of the author and do not necessarily represent those of LRGHealthcare.


___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] special stain storage

2010-07-26 Thread Tench, Bill
The critical issue that your CLIA, or perhaps CAP, inspector is going to
be asking is:  is it necessary to storage stain reagent X in a
refrigerator with a temperature range of Y.  That answer lies in your
procedure.  If it says refrigerate (perhaps with a range) reagent X,
then you must document that you have done so by tracking the frig
temperature. If it really is not necessary to refrigerate the reagent
(perhaps it is done so just to keep it from evaporating) indicate that
in the procedure.
 
Bill Tench
Associate Dir. Laboratory Services
Chief, Cytology Services
Palomar Medical Center
555 E. Valley Parkway
Escondido, California  92025
bill.te...@pph.org
Voice: 760- 739-3037
Fax: 760-739-2604
 

[None] made the following annotations
-
NOTICE: This email message is for the sole use of the intended recipient(s) 
 and may contain confidential and privileged information. Any unauthorized 
 review, use, disclosure or distribution is prohibited. If you are not the 
 intended recipient, please contact the sender by reply email and destroy all 
 copies of the original message. 

This message has been content scanned by the Axway MailGate. 
MailGate uses policy enforcement to scan for known viruses, spam, undesirable 
content and malicious code. For more information on Axway products please visit 
www.axway.com.
-

___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] Powdered reagent expiration dates

2010-07-26 Thread Pat Laurie
We were inspected by CAP on friday and we were cited for


ANP.21366  *Are reagents and solutions properly labeled, as applicable and
appropriate, with the following elements?*

* *

1.  *Content and quantity, concentration or titer*

2.  *Storage requirements*

3.  *Date prepared or reconstituted by laboratory*

4.  *Expiration date*

Specifically that our staining powders didn't have an expiration date
printed on the bottle. All of our reconsituted reagents which are in
use were dated with an expiration date properly though. I have always
assumed, perhaphs incorrectly, that powdered stains never expire.  We have
powders like Luxol Echt Blau, etc. that were purchased and opened over 40
years ago.If so, then these powdered reagents have gone through CAP
inspections since the beginning and this inspector was the first one to find
this problem.  Is this one that we might protest?

-- 
Patrick Laurie HT(ASCP)QIHC
CellNetix Pathology  Laboratories
1124 Columbia Street, Suite 200
Seattle, WA 98104
PH: 206-215-5949
plau...@cellnetix.com
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] powder stain expiration

2010-07-26 Thread Tench, Bill
If the manufacturer has not included an expiration date for these, i
think there probably isn't one.  I would call the CAP LAP folks and ask
them about that.  When this kind of issue arises during an inspection,
it is always better to call while the inspectors are still there.  You
can get an answer right then and there and it will save everyone a lot
of time and hassle.
 
Bill Tench
Associate Dir. Laboratory Services
Chief, Cytology Services
Palomar Medical Center
555 E. Valley Parkway
Escondido, California  92025
bill.te...@pph.org
Voice: 760- 739-3037
Fax: 760-739-2604
 

[None] made the following annotations
-
NOTICE: This email message is for the sole use of the intended recipient(s) 
 and may contain confidential and privileged information. Any unauthorized 
 review, use, disclosure or distribution is prohibited. If you are not the 
 intended recipient, please contact the sender by reply email and destroy all 
 copies of the original message. 

This message has been content scanned by the Axway MailGate. 
MailGate uses policy enforcement to scan for known viruses, spam, undesirable 
content and malicious code. For more information on Axway products please visit 
www.axway.com.
-

___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] Re: Phospho-Histone 3 (SER10) antibody

2010-07-26 Thread Andrea Marion
I have used a phospho-H3 Ser10 antibody successfully on FFPE sections of
adult mouse heart and mouse embryos. Ours is Millipore 06-570 (formerly
Upstate 06-570) Lot# DAM1644557 and HIER with 10mM sodium citrate buffer,
0.05% Tween-20 pH 6.0 works great.

In the past we tried a phospho H3 Ser10 antibody from Cell Signaling
Technology #9706 and it works fine on Western blots, but we could never
get it to work on immunostainings. This is a different antibody and
company from Millipore/Upstate.

Andrea Marion
Graduate Student
University of Illinois - Chicago
amario3 [at] uic [dot] edu



I have been trying without success to get this antibody to work.   Is
anyone doing this antibody?  We have the Leica Bond Max and would like
to perform it on this platform.  I have tried 2 antibodies from Cell
Signaling Technology without any success.   Any advice would be greatly
appreciated.

Thanks!

Martha Ward, MT (ASCP) QIHC
Assistant Manager, Molecular Diagnostics Lab
Wake Forest University Baptist Medical Center
336-716-2104






___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


Re: [Histonet] powder stain expiration

2010-07-26 Thread Bill B.
We verify these on control tissues yearly and keep a record whether or not 
there is an expiration date. I see no reason to throw away good material and 
waste yet more medical dollars. 

Bill Blank, MD

At 10:38 AM -0700 7/26/10, Tench, Bill wrote:
If the manufacturer has not included an expiration date for these, i
think there probably isn't one.  I would call the CAP LAP folks and ask
them about that.  When this kind of issue arises during an inspection,
it is always better to call while the inspectors are still there.  You
can get an answer right then and there and it will save everyone a lot
of time and hassle.


___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


Re: [Histonet] Powdered reagent expiration dates

2010-07-26 Thread DKBoyd
Some of our stains are very old also, about 10 years ago we wrote on a 
label on each stain; Opened prior to: with that days date and Stable.  We 
were CAP inspected many times after that and we had no problems.  Just as 
you would label your reagents you make up as Stable when there isn't an 
expiration time period.


Debbie M. Boyd, HT(ASCP) l Chief Histologist l Southside Regional Medical 
Center I 
200 Medical Park Boulevard l Petersburg, Va.  23805 l T: 804-765-5050 l F: 
804-765-5582 l dkb...@chs.net







Pat Laurie foreig...@gmail.com 
Sent by: histonet-boun...@lists.utsouthwestern.edu
07/26/2010 01:27 PM

To
Histonet@lists.utsouthwestern.edu
cc

Subject
[Histonet] Powdered reagent expiration dates






We were inspected by CAP on friday and we were cited for


ANP.21366  *Are reagents and solutions properly labeled, as applicable and
appropriate, with the following elements?*

* *

1.  *Content and quantity, concentration or titer*

2.  *Storage requirements*

3.  *Date prepared or reconstituted by laboratory*

4.  *Expiration date*

Specifically that our staining powders didn't have an expiration date
printed on the bottle. All of our reconsituted reagents which are in
use were dated with an expiration date properly though. I have always
assumed, perhaphs incorrectly, that powdered stains never expire.  We have
powders like Luxol Echt Blau, etc. that were purchased and opened over 40
years ago.If so, then these powdered reagents have gone through CAP
inspections since the beginning and this inspector was the first one to 
find
this problem.  Is this one that we might protest?

-- 
Patrick Laurie HT(ASCP)QIHC
CellNetix Pathology  Laboratories
1124 Columbia Street, Suite 200
Seattle, WA 98104
PH: 206-215-5949
plau...@cellnetix.com
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet



--
Disclaimer: This electronic message may contain information that is
Proprietary, Confidential, or legally privileged or protected. It
is intended only for the use of the individual(s) and entity named
in the message. If you are not an intended recipient of this
message, please notify the sender immediately and delete the
material from your computer. Do not deliver, distribute or copy
this message and do not disclose its contents or take any action in
reliance on the information it contains.
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] RE: Histonet Digest, Vol 80, Issue 30

2010-07-26 Thread prashant sareen

Try reducing the processing time and try very fine cutting and I think the 
microchatter will go.

 

 



Thanks
Prashant Sareen BS , M.B.A , HT (ASCP)
Associate Scientist III
Comprehensive Animal health Services
Bioreliance Corporation
14930 Broschart Road,

Rockville, MD 20850
Office: 301-610-2744
Histology: 301-610-2997

Cell: 240-315-5541
Email: prashant.sar...@bioreliance.com
  From: histonet-requ...@lists.utsouthwestern.edu
 Subject: Histonet Digest, Vol 80, Issue 30
 To: histonet@lists.utsouthwestern.edu
 Date: Mon, 26 Jul 2010 10:02:53 -0700
 
 Send Histonet mailing list submissions to
 histonet@lists.utsouthwestern.edu
 
 To subscribe or unsubscribe via the World Wide Web, visit
 http://lists.utsouthwestern.edu/mailman/listinfo/histonet
 or, via email, send a message with subject or body 'help' to
 histonet-requ...@lists.utsouthwestern.edu
 
 You can reach the person managing the list at
 histonet-ow...@lists.utsouthwestern.edu
 
 When replying, please edit your Subject line so it is more specific
 than Re: Contents of Histonet digest...
 
 
 Today's Topics:
 
 1. Re: Artifacts in histology section (Joseph Saby)
 2. Re water problem (Steven Weston)
 3. RE: Re water problem (Goins, Tresa)
 4. Re: Artifacts in histology section (kim.dona...@bhcpns.org)
 5. Special Stain Storage (kristen arvidson)
 6. RE: Special Stain Storage (Podawiltz, Thomas)
 
 
 --
 
 Message: 1
 Date: Sun, 25 Jul 2010 10:49:05 -0700 (PDT)
 From: Joseph Saby saby_josep...@yahoo.com
 Subject: Re: [Histonet] Artifacts in histology section
 To: Aazath Raj aaz...@hotmail.com, histonet@lists.utsouthwestern.edu
 Message-ID: 431113.5115...@web114420.mail.gq1.yahoo.com
 Content-Type: text/plain; charset=iso-8859-1
 
 What you are describing might be microchatter.  These will be sharp parallel 
 lines/cracks that run parallel to the knife edge and are only visible under 
 the 
 microscope.
 
 The usuall cause is a combination of overprocessing and rough facing that is 
 too 
 aggressive and/or with too dull a blade.  Overprocessing makes the tissue 
 very 
 hard and somewhat brittle.  The thick sections/dull knife cause the tissue to 
 compress and then release, causing the chatter.  The actual danage is in the 
 block face.
 
 Once you have the problem in a block, if the tissue is thick enough, you 
 might 
 be able to repeatedly soak the block in ice water and gently (with a fairly 
 sharp knife) reface.  With luck, you might be able to get through the damaged 
 block face.  
 
 
 Another artifact I have seen is similar, but the chatter appears very blurry. 
  
 This is usually caused be poor fixation/processing, then oversoaking the 
 blocks 
 after facing.  The trick here is to reface the block, then chill it without 
 exposure to water.  I've sectioned such blocks after placing them in a 
 freezer 
 to chill them thoroughly.  This will help to obtain a section, but may not 
 fix 
 the staining problems that might show up later.  
 
 
 Good luck!
 
 Joe Saby, BA HT
 
 
 
 
 
 From: Aazath Raj aaz...@hotmail.com
 To: histonet@lists.utsouthwestern.edu
 Sent: Fri, July 23, 2010 11:26:28 AM
 Subject: [Histonet] Artifacts in histology section
 
 
 
 Dear Friends,
 
   I am an Histology Technologist. I am having a problem 
 here,while 
 sectioning am not seeing and scoring artifacts on the section but in the 
 microscope am seeing a tearing artifacts particularly in endoscopy biopsies. 
 am 
 not able to locate where is the problem,is that because of blades or due to 
 micro-crystallization of wax or due to any processing problem. Its not 
 consistently in all but i get it on some blocks every  day. Can any one help 
 me 
 in sorting it out. If anybody is interested in will send the picture of those 
 section.
 
 
 
 
 
 with regards,
 
 Aazathraj.P
 
 Technical Officer,
 
 Apollo Hospitals-chennai
 
 India.
 
 aaz...@hotmail.com
 
 
 
 _
 The latest in fashion and style in MSN Lifestyle
 http://lifestyle.in.msn.com/___
 Histonet mailing list
 Histonet@lists.utsouthwestern.edu
 http://lists.utsouthwestern.edu/mailman/listinfo/histonet
 
 
 
 
 
 --
 
 Message: 2
 Date: Mon, 26 Jul 2010 13:49:31 +1000
 From: Steven Weston steven.wes...@utas.edu.au
 Subject: [Histonet] Re water problem
 To: histonet list histonet@lists.utsouthwestern.edu
 Message-ID: c87342eb.2535%steven.wes...@utas.edu.au
 Content-Type: text/plain; charset=iso-8859-1
 
 We had this problem when we started using APTS coated slides and left out 
 adhesive from the water bath. A simple solution I have found is to add a 
 single drop of triton x100 (or similar detergent) to my full water bath and 
 mix before heating the water. This reduces the surface tension of the water 
 and allows it to run off the 

Re: [Histonet] Powdered reagent expiration dates

2010-07-26 Thread Angela Bitting
Coincidentally, I had a question on this subject this morning. We rec'd in some 
oxalic acid and phoshotungstic acid, neither of which had expiration dates. I 
called Fisher and they looked it up for me and told me their expiration and 
offered to send it to me in writing, if I wanted. (it was 3-5 years from the 
manufacture date.) I was recently told by another tech that she thought 5 years 
was the shelf life of powders, but I wanted to see if that held true. Moral of 
the story is that it never hurts to call the manufacturer.

Angela Bitting, HT(ASCP), QIHC
Technical Specialist, Histology
Geisinger Medical Center 
100 N Academy Ave. MC 23-00
Danville, PA 17822
phone  570-214-9634
fax  570-271-5916 
 
No trees were hurt in the sending of this email
However many electrons were severly inconvienienced!


 Pat Laurie foreig...@gmail.com 7/26/2010 1:27 PM 
We were inspected by CAP on friday and we were cited for


ANP.21366  *Are reagents and solutions properly labeled, as applicable and
appropriate, with the following elements?*

* *

1.  *Content and quantity, concentration or titer*

2.  *Storage requirements*

3.  *Date prepared or reconstituted by laboratory*

4.  *Expiration date*

Specifically that our staining powders didn't have an expiration date
printed on the bottle. All of our reconsituted reagents which are in
use were dated with an expiration date properly though. I have always
assumed, perhaphs incorrectly, that powdered stains never expire.  We have
powders like Luxol Echt Blau, etc. that were purchased and opened over 40
years ago.If so, then these powdered reagents have gone through CAP
inspections since the beginning and this inspector was the first one to find
this problem.  Is this one that we might protest?

-- 
Patrick Laurie HT(ASCP)QIHC
CellNetix Pathology  Laboratories
1124 Columbia Street, Suite 200
Seattle, WA 98104
PH: 206-215-5949
plau...@cellnetix.com 
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu 
http://lists.utsouthwestern.edu/mailman/listinfo/histonet



IMPORTANT WARNING: The information in this message (and the documents attached 
to it, if any) is confidential and may be legally privileged. It is intended 
solely for the addressee. Access to this message by anyone else is 
unauthorized. If you are not the intended recipient, any disclosure, copying, 
distribution or any action taken, or omitted to be taken, in reliance on it is 
prohibited and may be unlawful. If you have received this message in error, 
please delete all electronic copies of this message (and the documents attached 
to it, if any), destroy any hard copies you may have created and notify me 
immediately by replying to this email. Thank you.BEGIN:VCARD
VERSION:2.1
X-GWTYPE:USER
FN:Bitting, Angela
TEL;WORK:570-271-6844
ORG:;Histology
EMAIL;WORK;PREF;NGW:akbitt...@geisinger.edu
N:Bitting;Angela
END:VCARD

___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] Re: Special Stain Storage

2010-07-26 Thread Woodward, Denise
Hi All,
In Charles J Churukian's  Manual of the Special Stains Laboratory of the 
Department of Pathology and Laboratory Medicine, University of Rochester 
Medical Center, Rochester, NY  pg 192, he suggests the following chemicals 
should be kept refrigerated:  all buffer solutions, hydroquinone, 
Phosphomolybdic acid, Phosphotungstic acid, Protargol, silver nitrate and all 
solutions containing silver nitrate.   This information is under the section 
labeled Stability of Special Staining Solutions - General  guidelines 
Concerning Solutions.

Everywhere I have ever worked, we also kept the Schiff's reagent refrigerated 
for longer shelf life.

Regards,
Denise Long Woodward, MS, HT (ASCP) HTL,  QIHC
University of Connecticut

-Original Message-
From: histonet-boun...@lists.utsouthwestern.edu 
[mailto:histonet-boun...@lists.utsouthwestern.edu] On Behalf Of kristen arvidson
Sent: Monday, July 26, 2010 12:08 PM
To: histonet
Subject: [Histonet] Special Stain Storage

Hello All,
We were recently inspected by CLIA and our inspector noticed that we didn't 
have reagent storage temperatures written in our Special Stains procedures.? We 
do our stains by hand so we do have some stored in the refrigerator and others 
stored at room temp.? I went through some of the Histo books and I cannot find 
any specifics on storage of reagents.? Any suggestions??
?
Thanks!!
Kristen



___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


[Histonet] Myocardium infected with influenza

2010-07-26 Thread Mark Elliott
Does anyone have a block of myocardial tissue with a known influenza infection 
they can spare?  Even a few slides would be great.  
Thanks
Mark
 
 

***CONFIDENTIALITY NOTICE***
This electronic message and any attachments are intended only for the use of 
the addressee and may contain information that is privileged and confidential.  
Any dissemination, distribution or copying of this communication by 
unauthorized individuals is strictly prohibited. If you have received this 
communication in error, please notify the sender immediately by reply e-mail 
and delete the original and all copies from your system.

___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


RE: [Histonet] Powdered reagent expiration dates

2010-07-26 Thread Lee Peggy Wenk
See if you can get the following article. Biotech Histochem is published by
the Biological Stain Commission. http://www.biologicalstaincommission.org/

Biotech Histochem. 2009 Feb;84(1):11-5.

Stain and dye stability over a 30-year period: a comparison of certified dye
powders by the Biological Stain Commission.
Penney DP, Frank M, Fagan C, Willis C.

Biological Stain Commission, Department of Pathology  Laboratory Medicine,
University of Rochester Medical Center, Rochester, New York 14642-0001, USA.
david_pen...@urmc.rochester.edu

Abstract
The Biological Stain Commission (BSC) Assay Laboratory has received numerous
inquiries during the past several years regarding the long-term stability of
stain and dye powders, particularly since packaging requirements call for
expiration dates on reagents. We have conducted a study to examine the
long-term stability of selected dye powders. We used the standard procedures
of the BSC for testing biological stains for certification to give an
indication of the long-term chemical stability as well as staining
performance of the dye powders. An earlier study by Emmel and Stotz examined
the stability of various dye powders after a five-year storage period. The
present study is a follow-up project covering the same dyes after storage
for 30 years. The dye samples chosen for the study are the same samples used
in the five-year storage period study and give comparative results for all
three time periods. The results of this study affirm the generally held
speculation that dye powders are stable for many years and thus have a
substantial shelf-life. 

Peggy A. Wenk, HTL(ASCP)SLS
Beaumont Hospital
Royal Oak, MI 48073

-Original Message-
From: histonet-boun...@lists.utsouthwestern.edu
[mailto:histonet-boun...@lists.utsouthwestern.edu] On Behalf Of Pat Laurie
Sent: Monday, July 26, 2010 1:27 PM
To: Histonet@lists.utsouthwestern.edu
Subject: [Histonet] Powdered reagent expiration dates

We were inspected by CAP on friday and we were cited for


ANP.21366  *Are reagents and solutions properly labeled, as applicable and
appropriate, with the following elements?*

* *

1.  *Content and quantity, concentration or titer*

2.  *Storage requirements*

3.  *Date prepared or reconstituted by laboratory*

4.  *Expiration date*

Specifically that our staining powders didn't have an expiration date
printed on the bottle. All of our reconsituted reagents which are in use
were dated with an expiration date properly though. I have always assumed,
perhaphs incorrectly, that powdered stains never expire.  We have powders
like Luxol Echt Blau, etc. that were purchased and opened over 40
years ago.If so, then these powdered reagents have gone through CAP
inspections since the beginning and this inspector was the first one to find
this problem.  Is this one that we might protest?

--
Patrick Laurie HT(ASCP)QIHC
CellNetix Pathology  Laboratories
1124 Columbia Street, Suite 200
Seattle, WA 98104
PH: 206-215-5949
plau...@cellnetix.com
___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet


___
Histonet mailing list
Histonet@lists.utsouthwestern.edu
http://lists.utsouthwestern.edu/mailman/listinfo/histonet